Servers User's Guide
Table Of Contents
- SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers RCI User’s Guide
- Preface
- Contents
- Figures
- CHAPTER 1 RCI Overview
- CHAPTER 2 Setup of the RCI for Operation
- 2.1 Overview of RCI Setup
- 2.2 RCI Setup for Initial Installation
- 2.2.1 RCI setup flow
- 2.2.2 Confirming RCI initialization
- . To confirm RCI initialization:
- 2.2.3 Connecting RCI cables
- 2.2.4 Making an RCI address setting
- . To specify an RCI address:
- . To confirm an RCI address:
- 2.2.5 Making an RCI construction setting
- . To make an RCI construction setting:
- . To confirm an RCI construction setting:
- 2.3 RCI Setup for Addition of an RCI I/O Unit
- 2.4 RCI Setup for Addition of an RCI Base Cabinet
- 2.4.1 RCI setup flow
- 2.4.2 Confirming RCI initialization
- . To confirm RCI initialization:
- 2.4.3 Connecting an RCI cable
- 2.4.4 Making an RCI address setting
- . To specify an RCI address:
- . To confirm the specified RCI address:
- 2.4.5 Making an RCI expansion setting
- . To make an RCI expansion setting:
- . To confirm an RCI expansion setting:
- 2.5 RCI Setup for Replacement of an RCI I/O Unit
- 2.6 RCI Setup for Replacement of an RCI Base Cabinet
- 2.6.1 RCI setup flow
- 2.6.2 Replacing an RCI host
- 2.6.3 Confirming RCI initialization
- . To confirm RCI initialization:
- 2.6.4 Connecting an RCI cable
- 2.6.5 Making an RCI address setting
- . To specify an RCI address:
- . To confirm the specified RCI address:
- 2.6.6 Making an RCI replacement setting
- . To make an RCI replacement setting:
- . To confirm an RCI replacement setting:
- CHAPTER 3 Command Reference
- CHAPTER 4 Error Status
C120-E360-06EN 3-9
3.2 setrcic
•OPTIONS
The following options are supported:
•OPERANDS
The following operands are supported:
• EXTENDED DESCRIPTION
z When the setrci(8) command or setrcic(8) command is being executed on another
host in the RCI network, do not execute the setrcic(8) command.
z When the setrcic(8) command is executed, set all RCI units that are connected to
RCI into the power-on state or standby state.
z Executing the setrcic(8) command on a model that does not support the RCI
function causes an error to occur.
-c exrdy
RCI_address
[time]
Sets the EXRDY monitoring timeout period of the specified external
power control devices. Set the EXRDY monitoring timeout period in
units of minutes for time. If 0 is specified, EXRDY monitoring is
disabled. If time is omitted, the EXRDY monitoring timeout period is
displayed.
-c opcalldisp Displays the status of the operator call signals of the specified external
power control devices.
-c opcallon
RCI_address
callNo
Sets the operator call signals of the specified external power control
devices on. Setting is made for the devices corresponding to the bits of
callNo that contain "1".
-c opcalloff
RCI_address
callNo
Sets the operator call signals of the specified external power control
devices off. Setting is made for the devices corresponding to the bits of
callNo that contain "1".
-h Displays usage statement. When used with other options or operands, an
error occurs.
RCI_address Specifies a target RCI address. A value in any of the following ranges
can be specified for RCI_address:
003001ff-00307fff
007001ff-00707fff
time Sets the EXRDY monitoring timeout period when "-c exrdy" is specified
in units of minutes. Any decimal integer number ranging from 0 to 85
can be specified.
callNo Specifies operator call information. A two-digit hexadecimal number
can be specified.