.com COMPONENT Technisches Handbuch / Technical Manual Systembaugruppe / Systemboard D1382
Are there ... ... any technical problems or other questions which you would like to be clarified? Please contact: your sales partner your sales outlet · · Further information can be found in the "Safety and Ergonomics" manual. The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.com Are there ... ...
Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.
German English Systembaugruppe D1387 System Board D1387 Technisches Handbuch Technical Manual Ausgabe April 2002 April 2002 edition
Pentium and Celeron are registered trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged.
Contents Introduction........................................................................................................................................1 Notational conventions ..............................................................................................................1 Important notes..................................................................................................................................1 Information about boards ..............................................
Introduction i Depending on the configuration chosen, some of the hardware components described may not be available on your system board. You will find further information in the "BIOS Setup" description. Further information about drivers is provided in the readme files on the hard disk, on the supplied drivers diskettes, on the "Drivers & Utilities" or on the "ServerStart" CD.
Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Connecting cables for peripherals must be adequately shielded to avoid interference. ! Components can become very hot during operation.
Features Features The components and connectors marked are not necessarily present on the system board. · · System board in µATX format Intel processor Pentium 4 from 1.4 GHz and with 400 /533 MHz Front Side Bus. Pentium 4 processors support MMX technology and Intel Streaming SIMD Extensions. The size and frequency of first-level cache and second-level cache are dependent upon the processor used.
Features · 1 AGP slot The AGP slot supports 4x AGP mode. Only AGP boards with 1.5 V are supported. · IDE hard disk controller connected to PCI bus for up to four IDE drives (e.g. IDE hard disk drives, ATAPI CD-ROM drives) The IDE hard disk controller are ATA100, ultra DMA capable and support PIO modes 0-4. · · · · · · · · · Floppy disk drive controller (possible formats: 720 KB, 1.44 MB, 2.88 MB) The system board supports booting from a 120 MB IDE floppy disk drive.
Features Internal ports and connectors 1 2 3 4 5 7 6 8 9 10 11 12 DIMM 2 DIMM 1 17 Power supply ATX Floppy Disk Drive IDE drives 3 and 4 (secondary) Power supply monitoring Connector for front panel IDE drives 1 and 2 (primary) Fan 2 OEM LED Cover monitoring PCI 3 15 14 13 16 1= 2= 3= 4= 5= 6= 7= 8= 9= PCI 2 PCI 1 AGP 13 10 = 11 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = LCD display USB ports C / D USB ports E / F COM2 SP/DIF (digital Audio) Audio front panel CD audio input Power supply Fan 1 (e
Features Temperature / System monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating. In addition, any unnecessary noise is also prevented by reducing the fan speed, and information is provided about the system status. Cover monitoring protects the system from unauthorised opening. An onboard controller developed by Fujitsu Siemens Computers controls the temperature and system monitoring.
Features Voltage monitoring: The voltages 12 V, 5 V and the CMOS battery are monitored.
Features Screen resolution Depending on the operating system used, the screen resolutions in the following table refer to the system board screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller.
Settings with switches and jumpers Settings with switches and jumpers ON 1 2 3 4 i Switch 1 = must always be set to off Switch 2 = System BIOS recovery Switch 3 = must always be set to off Switch 4 = must always be set to off The clock frequency of the processor is set automatically. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed.
Add-on modules Add-on modules ! Exit Suspend mode, switch off the device and remove the power plug from the mains supply, before carrying out any of the procedures described in this chapter! Even when you have switched off the device, parts (e.g. memory modules, AGP and PCI extension boards) are still supplied with power. All PCI slots support 3.3 V main and auxiliary voltages. AGP boards support 1,5 V main and auxiliary voltages.
Add-on modules Installing and removing processors 3 2 4 5 1 A Ê Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Remove the old processor from the socket (3). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). ! Ê The angled corner of the processor may be covered by the heat sink.
Add-on modules Upgrading main memory These slots are suitable for 128, 256, 512 and 1024 Mbyte DDR memory modules of the DIMM format. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2,5 V memory modules. Buffered memory modules are not supported. DDR-DIMM memory modules must meet the PC2100 specification. Installing a memory module 2 2 Ê Ê Ê Push the holders on each side of the memory compartment outwards. Insert the memory module into the location (1).
Add-on modules Replacing the lithium battery ! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Ensure that you insert the battery the right way round.
Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board.
