Installation Guide English SPARC® Enterprise T5140 / T5240 Servers
SPARC® Enterprise T5140 and T5240 Servers Installation Guide Order No. U41767-J-Z816-1-76 Part No.
Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. FUJITSU LIMITED provided technical input and review on portions of this material. Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document, and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws and international treaties.
Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, Etats-Unis. Tous droits réservés. Entrée et revue tecnical fournies par FUJITSU LIMITED sur des parties de ce matériel. Sun Microsystems, Inc. et Fujitsu Limited détiennent et contrôlent toutes deux des droits de propriété intellectuelle relatifs aux produits et technologies décrits dans ce document.
Contents Preface 1. xiii Preparing for Installation 1 Tools and Equipment Needed 3 Optional Component Installation ESD Precautions 3 3 Installation Overview 4 Cabling Notes for Both Servers 6 Port, Connector, and LED Locations for Both Servers Slide Rail Assembly Notes for Both Servers 10 Cable Management Notes for Both Servers 13 Safety Precautions 2.
Connecting the Server Cables for Both Servers ▼ To Connect the Service Processor Serial Management Port ▼ To Connect the Service Processor Network Management Port ▼ To Connect the Ethernet Network Cables ▼ To Connect the AC Power Cable to the Server Managing Cables With the CMA ▼ 33 34 35 37 Powering On the System for the First Time ILOM System Console ILOM Service Processor 37 37 38 To Power On the System for the First Time 38 Enabling the Service Processor Network Management Port Logging
▼ To Power Cycle the System Verifying System Functionality A. Updating the Firmware ▼ B. Selecting a Boot Device C.
viii SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Figures FIGURE 1-1 SPARC Enterprise T5140 Server 2 FIGURE 1-2 SPARC Enterprise T5240 Server 2 FIGURE 1-3 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5140 Server FIGURE 1-4 Front Panel USB Ports on the SPARC Enterprise T5140 Server FIGURE 1-5 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5240 Server FIGURE 1-6 Front Panel USB Ports on the SPARC Enterprise T5240 Server FIGURE 1-7 Sections of the Slide Rail Assembly on the SPARC Enterprise T5240 Server FIGURE
FIGURE 2-12 Unlocking the Slide Rail Assembly (Either Server) FIGURE 2-13 Rail Mounting Bracket Release Button (Either Server) FIGURE 2-14 Service Processor Serial Management Port – Rear Panel FIGURE 2-15 Service Processor Network Management Port – Rear Panel FIGURE 2-16 Service Processor Ethernet Network Ports – Rear Panel FIGURE 2-17 Securing the Server Cables With the CMA and Velcro Straps (Either Server) FIGURE 3-1 Server Connections FIGURE C-1 Sections of the Express Rail Slide Rail Asse
Tables TABLE 1-1 Ethernet Connection Transfer Rates 7 TABLE 3-1 Disk Slot Numbers, Logical Device Names, and Physical Device Names TABLE 3-2 Device Identifiers and Devices 55 55 xi
xii SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Preface This manual provides instructions, background information, and reference material to help you install SPARC® Enterprise T5140 and T5240 servers. The installation instructions in this document assume that a system administrator is experienced with the Solaris™ Operating System (Solaris OS). Note – All internal components except hard drives must be installed by qualified service technicians only.
Structure and Contents of This Manual This manual is organized as described below: Chapter 1 provides an installation overview for the servers. Chapter 2 provides instructions for installing the servers into a rack. Chapter 3 provides instructions for configuring and powering on the servers, and for installing additional software. Appendix A provides instructions for updating the service processor firmware and the system firmware. Appendix B provides instructions for selecting a boot device.
Related Documentation The latest versions of all the SPARC Enterprise Series manuals are available at the following Web sites: http://manuals.fujitsu-siemens.com/ Title Description Order No.
Using UNIX Commands This document might not contain information about basic UNIX® commands and procedures such as shutting down the system, booting the system, and configuring devices. Refer to the following for this information: ■ Software documentation that you received with your system ■ Solaris™ Operating System documentation, which is at: http://docs.sun.com Text Conventions This manual uses the following fonts and symbols to express specific types of information.
Prompt Notations The following prompt notations are used in this manual.
Caution – This indicates that hazardous voltages are present. To reduce the risk of electric shock and danger to personal health, follow the instructions. Tip – This indicates information that could help the user to use the product more effectively. Alert messages in the text An alert message in the text consists of a signal indicating an alert level followed by an alert statement. Alert messages are indented to distinguish them from regular text.
Notes on Safety Important Alert Messages This manual provides the following important alert signals: Caution – This indicates a hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This signal also indicates that damage to the product or other property may occur if the user does not perform the procedure correctly. Task Warning Installation Damage Deploy the antitilt feature on the rack before beginning an installation.
Caution – This indicates that hazardous voltages are present. To reduce the risk of electric shock and danger to personal health, follow the instructions. xx Task Warning Installation Electric shock There is a potential for electric shock if the server and related equipment are not properly grounded.
Product Handling Maintenance Warning – Certain tasks in this manual should only be performed by a certified service engineer. User must not perform these tasks. Incorrect operation of these tasks may cause electric shock, injury, or fire.
Alert Label The following is a label attached to this product: ■ Never peel off the label. ■ The following label provides information to the users of this product. Example: SPARC Enterprise T5240 Server Fujitsu Siemens Computers Welcomes Your Comments We would appreciate your comments and suggestions to improve this document. You can submit your comments by using "Reader's Comment Form.
■ Reader's Comment Form Preface xxiii
FOLD AND TAPE NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO 741 SUNNYVALE CA POSTAGE WILL BE PAID BY ADDRESSEE FUJITSU COMPUTER SYSTEMS AT TENTION ENGINEERING OPS M/S 249 1250 EAST ARQUES AVENUE P O BOX 3470 SUNNYVALE CA 94088-3470 FOLD AND TAPE xxiv SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
CHAPTER 1 Preparing for Installation This chapter provides background information about the installation procedures for both servers that are provided in Chapter 2.
2 FIGURE 1-1 SPARC Enterprise T5140 Server FIGURE 1-2 SPARC Enterprise T5240 Server SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Tools and Equipment Needed To install the system, you must have the following tools: ■ No. 2 Phillips screwdriver ■ ESD mat and grounding strap In addition, you must provide a system console device, such as one of the following: ■ ASCII terminal ■ Workstation ■ Terminal server ■ Patch panel connected to a terminal server Optional Component Installation The standard components of the server are installed at the factory.
Caution – To protect electronic components from electrostatic damage, which can permanently disable the system or require repair by service technicians, place components on an antistatic surface, such as an antistatic discharge mat, an antistatic bag, or a disposable antistatic mat. Wear an antistatic grounding strap connected to a metal surface on the chassis when you work on system components.
Tip – The serial terminal or a terminal emulator should be connected before you connect the power cables. As soon as AC power is connected to the system, the service processor immediately powers on and runs diagnostics. Diagnostic test failures will be printed on the serial terminal. For more information, refer to the Integrated Lights Out Manager 2.0 Supplement for SPARC Enterprise T5140 and T5240 Servers. 6. Connect the data cables to the server, but do not connect the AC power cable yet.
Refer to the SPARC Enterprise T5140 and T5240 Servers Product Notes for a list of required patches. 14. Load additional software from the Solaris media kit (optional). The Solaris media kit (sold separately) includes several CDs containing software to help you operate, configure, and administer your server. Refer to the documentation provided with the media kit for a complete listing of included software and detailed installation instructions.
■ Ethernet ports are labeled NET0, NET1, NET2, and NET3. The Ethernet interfaces operate at 10 Mbps, 100 Mbps, and 1000 Mbps. TABLE 1-1 shows the transfer rates for the Ethernet ports. TABLE 1-1 Ethernet Connection Transfer Rates Connection Type IEEE Terminology Transfer Rate Ethernet 10BASE-T 10 Mbit/sec Fast Ethernet 100BASE-TX 100 Mbits/sec Gigabit Ethernet 1000BASE-T 1000 Mbit/sec ■ TTYA serial port: Use the DB-9 connector with a null modem cable for serial devices.
FIGURE 1-3 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5140 Server 15 1 2 3 4 5 6 7 8 16 9 17 10 11 12 13 14 Figure Legend 1 Power supply 0 10 Gbit Enet port NET2 2 Power supply 1 11 Gbit Enet port NET3 3 Locator LED button 12 USB port 0 4 Service Required LED 13 USB port 1 5 Power OK LED 14 TTYA serial port 6 Service processor serial management port 15 PCIe/XAUI slot 0 7 Service processor network management port 16 PCIe/XAUI slot 1 8 Gbit En
See FIGURE 1-5 and FIGURE 1-6 for the locations of the ports on the SPARC Enterprise T5240 server.
FIGURE 1-6 Front Panel USB Ports on the SPARC Enterprise T5240 Server 1 2 3 4 5 6 7 8 9 10 11 Figure Legend 1 System status indicators: Top to bottom: Power button, Power OK LED, Service Required LED, Locator LED Button 7 Hard drive HDD5 2 Hard drive HDD0 8 Hard drive HDD6 3 Hard drive HDD1 9 Hard drive HDD7 4 Hard drive HDD2 10 USB port 2 5 Hard drive HDD3 11 USB port 3 6 Hard drive HDD4 Slide Rail Assembly Notes for Both Servers The rackmount kit has two slide rail asse
FIGURE 1-7 Sections of the Slide Rail Assembly on the SPARC Enterprise T5240 Server 1 2 3 4 Figure Legend 1 Mounting bracket 3 Middle section 2 Front section 4 Rear section ■ The front, middle, and rear sections form the slide rail. The middle and rear sections have holes for mounting screws, and adjust to fit rack depths from 24 in. (61 cm) to 36.5 in. (93 cm). The front section can be extended to allow movement of the server out of the rack. ■ The removable mounting bracket slides 14 in.
FIGURE 1-8 12 Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise T5240 Server SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Cable Management Notes for Both Servers The same cable management arm (CMA) is included with the rackmounting kit for each server (FIGURE 1-9). The CMA clips onto the slide rails. Use the velcro straps to secure cabling to the CMA.
Safety Precautions Caution – Deploy the antitilt bar on the equipment rack before beginning an installation. Caution – The SPARC Enterprise T5240 server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount this 2U server into a rack enclosure when using the procedures in this document. Caution – When completing a two-person procedure, always communicate your intentions clearly before, during, and after each step to minimize confusion.
CHAPTER 2 Installing the SPARC Enterprise T5140 and T5240 Servers This chapter provides instructions for installing the servers into an equipment rack. Note – If your rackmount kit came with its own instructions, use the instructions in your rackmount kit instead of the instructions in this chapter. After performing the server installation, proceed to Chapter 3 for first-time power on.
Note – The procedures in this chapter are the same for both the 1U and 2U servers. The illustrations show a 2U server only as an example. The rackmount kit (same for both 1U and 2U servers) contains two slide rail assemblies, which can be installed on either the right or left side of the rack. A slide rail assembly consists of two parts: a slide rail and a removable mounting bracket. The slide rail attaches to the rack posts. The mounting bracket attaches to the server chassis.
c. Slide the mounting bracket release button in the direction shown in FIGURE 2-2, then slide the mounting bracket out of the slide rail. FIGURE 2-2 Location of the Mounting Bracket Release Button (Either Server) d. Press the metal lever (labeled Push) on the middle section (FIGURE 2-3) of the sliding rail, then push the middle section back into the rack.
FIGURE 2-3 Unlocking the Slide Rail Middle Section (Either Server) Metal lever 2. Attach a mounting bracket to the right side of the chassis. a. Position the mounting bracket against the chassis (FIGURE 2-4). Ensure that the slide rail lock is at the front and the three keyed openings on the mounting bracket are aligned with the three locating pins on the side of the chassis.
FIGURE 2-4 Attaching a Mounting Bracket to the Chassis (Either Server) b. Ensure that the heads of the locating pins protrude though the keyed openings in the mounting bracket. Pull the mounting bracket toward the front of the chassis until the bracket locks into place with an audible click. c. Verify that all locating pins are trapped in the keyed openings and that the correct locating pin has engaged the mounting bracket lock. See the right side of FIGURE 2-4. 3.
■ If your rack does not have threaded mounting holes, the mounting screws are secured with a caged nut. 6. Attach a slide rail to the right front rack post. a. Loosely attach the front of a slide rail to the right front rack post using two screws (FIGURE 2-5). Note – Do not tighten the screws yet. FIGURE 2-5 Mounting a Slide Rail (Either Server) b. Adjust the length of the slide rail by sliding the rear mounting flange to reach the outside edge of the rear rack post. c.
8. Use the slide rail spacing tool to adjust the distance between the slide rails. a. At the front of the rack, plug the left side of the tool into slots at the end of the left rail (FIGURE 2-6). FIGURE 2-6 Using the Slide Rail Spacing Tool to Adjust the Distance Between the Slide Rails (Either Server) b. Insert the right side of the tool into the front end of the right rail. c. Slide the end of the rail to the right or left as needed to allow the ends of the tool to enter the ends of both rails.
▼ To Insert and Lock the Server in the Rack 1. Deploy the antitilt bar, if the chassis or rack is so equipped. Caution – The weight of the servers on extended slide rails can be enough to overturn an equipment rack. Caution – The 2U server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount the server into a rack enclosure when using the procedures in this chapter. 2. Insert the ends of the mounting brackets into the sliding rails (FIGURE 2-7).
3. Slide the chassis into the rack. Caution – Before continuing, verify that the server is securely mounted in the rack, and that the slide rails are locked to the mounting brackets. Installing the Cable Management Arm for Both Servers The rackmounting kit for each server comes with the same cable management arm (CMA) assembly. The CMA installation and cable management procedures are the same for both servers.
FIGURE 2-8 Inserting the CMA Rail Extension Into the Rear of the Left Slide Rail (Either Server) The right sides of the two CMA arms have hinged extensions. On the manufacturer’s instruction sheet, the smaller extension is called the CMA Connector for Inner Member. This extension attaches to the right mounting bracket. The larger extension is called the CMA Connector for Outer Member, and attaches to the right sliding rail.
3. Insert the smaller extension into the clip located at the end of the mounting bracket (FIGURE 2-9). Slide the smaller extension into the square hole on the middle-in-width of the clip that is located at the end of the mounting bracket.
4. Insert the larger extension into the end of the right sliding rail (FIGURE 2-10).
5. Insert the hinged plastic connector at the left side of the CMA fully into the CMA rail extension (FIGURE 2-11). The plastic tab on the CMA rail extension locks the hinged plastic connector in place.
▼ To Verify the Operation of the Slide Rails and the CMA Tip – Two people are needed for this procedure, one to move the server in and out of the rack, and one to observe the cables and CMA. 1. For a free-standing rack, deploy the antitilt bar. 2. Unlock the slide lock buttons (FIGURE 2-12) at the right and left sides of the chassis. 3. Slowly pull the server out of the rack until the slide rails reach their stops. FIGURE 2-12 Unlocking the Slide Rail Assembly (Either Server) 4.
7. Pull both slide rail release buttons toward you simultaneously and slide the server back into the rack (FIGURE 2-13). The server should slide smoothly into the rack without binding. FIGURE 2-13 Rail Mounting Bracket Release Button (Either Server) 8. Verify that the CMA retracted without binding. 9. Adjust the cable straps and CMA as required to secure the cables. See “Managing Cables With the CMA” on page 34.
Connecting the Server Cables for Both Servers To boot the server, you must connect and configure the network and serial ports. The procedures are given in the following sections.
Use this port for server management. This port is needed to set up the service processor network management port, as detailed in “Enabling the Service Processor Network Management Port” on page 44. Note – Use the service processor serial management port only for server management. It is the default connection between the service processor and a terminal or a computer. Caution – Do not attach a modem to this port. ● Connect a Category 5 cable from the SER MGT serial management port to the terminal device.
Note – The service processor network management port is configured by default to retrieve network settings with Dynamic Host Configuration Protocol (DHCP) and allow connections using Solaris Secure Shell (SSH). You might need to modify these settings for your network. Instructions are given in Chapter 3. ● ▼ Connect a Category 5 cable from the NET MGT network management port to your network switch or hub.
Powering on the system for the first time requires special preparation and procedures. For example, if you have not prepared a display before connecting the AC power cable, system messages could be lost. Caution – The server goes into Standby mode and the service processor initializes as soon as the AC power cable is connected to the power source. ● Go to “Powering On the System for the First Time” on page 37 for instructions on connecting the server to AC power.
Caution – Verify the operation of the slide rails and CMA, and cable service loops. Perform the steps in the following procedure again before continuing: “To Verify the Operation of the Slide Rails and the CMA” on page 29. Dismounting the Servers To install or replace internal parts in the server, you must first remove the server from the rack. For the removal procedure, refer to the SPARC Enterprise T5140 and T5240 Servers Service Manual.
Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers 35
36 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
CHAPTER 3 Powering On the System This chapter includes instructions for booting the servers and for enabling the service processor network management port.
Note – To see these status and error messages, connect a terminal or terminal emulator to the serial management port (SER MGT). For a basic procedure to connect a terminal or terminal emulator, see “To Power On the System for the First Time” on page 38. For a more detailed discussion on configuring the system console and connecting terminals, refer to the SPARC Enterprise T5140 and T5240 Servers Administration Guide.
■ No handshake A null modem configuration is needed, meaning the transmit and receive signals are reversed (crossed over) for DTE to DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to achieve the null modem configuration. Note – When you power on the server for the first time and you do not have a terminal or terminal emulator (PC or workstation) connected to the service processor serial management port, you will not see system messages.
FIGURE 3-1 Server Connections SER MGT RJ-45 NET MGT RJ-45 NET 0 to NET 3 RJ-45 Host to Ethernet SP to Ethernet RJ-45 to DB-25 crossover adapter RJ-45 to DB-9 crossover adapter Terminal device 4. (Optional) Connect an Ethernet cable between the server’s Net MGT port (FIGURE 3-1) and the network to which future connections to the SP and host will be made.
Note – Only one power connection is required for operation. Use two power connections for redundancy. The service processor runs on the 3.3V standby voltage. As soon as AC power is connected to the system, the service processor powers on, runs diagnostics, and initializes the ILOM firmware. After a few minutes, the SP login prompt appears on the terminal device. The host is not initialized or powered on yet. 7. At the terminal device, log in to the SP as root with a password of changeme.
9. When prompted, follow the onscreen instructions for configuring the Solaris Operating System on your host and enter the following configuration information. You will be prompted to confirm the configuration several times, enabling confirmation and changes. If you are not sure how to respond to a particular value, you can accept the default, and make future changes when the Solaris OS is running. Parameter Description Language Select a number from the displayed language list.
Time Zone Select the time zone. Date and Time Accept the default date and time or change the values. root Password Enter the root password twice. This password is for the superuser account for the Solaris OS on this server. This password is not the SP password. 10. Log in to the server and explore its capabilities. There are many commands you can use to verify the functionality of the system.
Enabling the Service Processor Network Management Port The service processor network management port is not operational unless your network employs DHCP, in which case the configuration in automatic. If you network uses DHCP, you can run this command -> show /SP/network to view your server’s network configuration information. For example, -> show /SP/network /SP/network Targets: Properties: commitpending = (Cannot show property) dhcp_server_ip = 10.8.31.5 ipaddress = 10.8.31.
2. Configure the service processor. See “To Configure the Service Processor Network Management Port” on page 47. 3. Commit the changes to the service processor parameters. See Step 5 in “To Configure the Service Processor Network Management Port” on page 47. You can now use the network management port at any time to access the service processor. See “To Log Into the Service Processor Using the Network Management Port” on page 50.
1. If this is the first time the system has been powered on, use the password command to change the root password. ... Starting OpenBSD Secure Shell server: sshd. Starting Servicetags listener: stlistener. Starting FRU update program: frutool. hostname login: root Password: changeme Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. ... Federal Acquisitions: Commercial Software -- Government Users Subject to Standard License Terms and Conditions. ...
▼ To Configure the Service Processor Network Management Port Note – If your network allows the use of DHCP, this configuration is performed automatically the first time you boot the system. Use this procedure only when: ■ You are unable to use DHCP on your network. ■ You need to modify the ILOM service processor network management port settings. In this procedure, you connect to the ILOM service processor using the serial management port to manually reconfigure the network management port.
a. If you choose to use a dynamically created IP address (use DHCP to retrieve the network setting), set pendingipdiscovery to dhcp. -> set /SP/network pendingipdiscovery=dhcp Set 'pendingipdiscovery' to 'dhcp' a. If you choose to configure a static IP configuration. set the parameters pendingipdiscovery, pendingipaddress, pendingipgateway, and pendingipnetmask as follows. i. Set the service processor to accept a static IP address.
CODE EXAMPLE 3-1 show /SP/network Command Output Properties: commitpending = (Cannot show property) dhcp_server_ip = xxx.xxx.xxx.xxx ipaddress = xxx.xxx.xxx.xxx ipdiscovery = dhcp ipgateway = xxx.xxx.xxx.xxx ipnetmask = 255.255.252.0 macaddress = 00:14:4F:3F:8C:AF pendingipaddress = xxx.xxx.xxx.xxx pendingipdiscovery = static pendingipgateway = xxx.xxx.xxx.xxx pendingipnetmask = 255.255.255.
▼ To Log Into the Service Processor Using the Network Management Port Note – You must configure the service processor parameters shown in “To Configure the Service Processor Network Management Port” on page 47 before you can use the network management port. ● Open an SSH session and connect to the service processor by specifying its network address. % ssh root@xx.xxx.xx.x ... Are you sure you want to continue connecting (yes/no)? yes ...
▼ To Power On the System 1. Perform the following steps to verify that there are no faults: a. Set the virtual keyswitch to diag mode so that POST will run in Service mode. -> set /SYS keyswitch_state=diag Set ’keyswitch_state’ to ’diag’ b. To initiate the power on sequence, type the start /SYS command. You will see an ILOM CLI alert message on the system console. This message indicates that the system has reset.
c. Switch to the system console to view POST output. -> start /SP/console Are you sure you want to start /SP/console (y/n)? y Serial console started. To stop, type #. . . . Watch the POST output for possible fault messages. The following output is a sign that POST did not detect any faults: . . . 2007-12-14 16:34:53.385 0:1:0>INFO: 2007-12-14 16:34:53.391 0:1:0> POST Passed all devices. 2007-12-14 16:34:53.399 0:1:0>POST: Return to VBSC. 2007-12-14 16:34:53.
4. Use the set /SYS keyswitch_state=normal command to return the virtual keyswitch to Normal mode (default) so that the system can power on and start the boot process. -> set /SYS keyswitch_state=normal Set ’keyswitch_state’ to ’normal’ ▼ To Connect to the System Console Output from POST, OpenBoot, and the Solaris OS is displayed in the system console using the network console on the service processor. ● Type the start /SP/console command.
The CPU and memory controllers initialize, and eventually OpenBoot initializes. After a number of system console messages, the ok prompt appears, or the system will boot into the Solaris OS. Note – System behavior depends on how the auto-boot variable is set. See the SPARC Enterprise T5140 and T5240 Servers Service Manual for more information. The following example output is a small section of the complete output. 0:1:0> 0:1:0>SPARC-Enterprise[TM] T5140/T5240 POST 4.27.x. 2007/12/11 18:55 ...
TABLE 3-1 Disk Slot Numbers, Logical Device Names, and Physical Device Names (Continued) Disk Slot Number Logical Device Name* Physical Device Name Slot 1 c0t1d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@1,0 Slot 2 c0t2d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@2,0 Slot 3 c0t3d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@3,0 * The logical device names might appear differently on your system, depending on the number and type of add-on disk controllers installed.
▼ To Boot the Solaris Operating System 1. At the ok prompt, boot from the disk that contains the Solaris OS. ■ If you know which disk to boot from, skip this step and perform Step 2.
▼ To Reset the System ● If it is necessary to reset the system, use the shutdown -g0 -i6 -y command. # shutdown -g0 -i6 -y It is not necessary to power the system off and on to simply reset the system. ▼ To Power Cycle the System If a simple reset does not clear a system problem, you can power the system off and on with this procedure. 1. Shut down the Solaris OS. At the Solaris OS prompt, type the shutdown -g0 -i0 -y command.
Note – To perform an immediate and ungraceful shutdown, use the stop -force -script /SYS or stop -script /SYS commands. These commands stop everything immediately, ensure that all data is saved before entering these commands. 4. Type the start /SYS command. -> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS -> Note – To force a power-on sequence, use the start -script /SYS command. 5. Reconnect to the system console with the start /SP/console command.
Chapter 3 Powering On the System 59
60 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
APPENDIX A Updating the Firmware This appendix provides instructions for updating SP firmware. ■ “The flashupdate command” on page 61 ■ “Updating the Firmware” on page 61 The flashupdate command The flashupdate command updates both the service processor firmware and the server firmware.
▼ To Update the Firmware 1. Ensure that the ILOM service processor network management port is configured. This configuration is required to access the new flash image over the network. See “To Configure the Service Processor Network Management Port” on page 47. 2. Open an SSH session to connect to the service processor. % ssh root@xx.xxx.xx.x ... Are you sure you want to continue connecting (yes/no)? yes ... Password: password (nothing displayed) Waiting for daemons to initialize...
■ Full path name to the flash image that the IP address can access The command usage is as follows: load [-script] -source tftp://xxx.xxx.xx.xx/pathname where: ■ -script – Does not prompt for confirmation and acts as if yes was specified ■ -source – Specifies the IP address and full path name (URI) to the flash image -> load -source tftp://xxx.xxx.xx.xx/pathname NOTE: A firmware upgrade will cause the server and ILOM to be reset.
CODE EXAMPLE A-1 Typical Boot Sequence Following Firmware Update (Continued) ... done. Mounting local filesystems... Cleaning /tmp /var/run /var/lock. Identifying DOC Device Type(G3/G4/H3) ... OK Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.1 Copyright 2007 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/products/DHCP eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
APPENDIX B Selecting a Boot Device This appendix provides instructions on selecting a boot device. ■ “Selecting a Boot Device” on page 65 Selecting a Boot Device The boot device is specified by the setting of an OpenBoot configuration variable called boot-device. The default setting of this variable is disk net. Because of this setting, the firmware first attempts to boot from the system hard drive, and if that fails, from the on-board NET0 Gigabit Ethernet interface.
▼ To Select a Boot Device ● At the ok prompt, type: ok setenv boot-device device-specifier where the device-specifier is one of the following: ■ cdrom – Specifies the DVD drive ■ disk – Specifies the system boot disk (internal disk 0 by default) ■ disk0 – Specifies internal drive 0 ■ disk1 – Specifies internal drive 1 ■ disk2 – Specifies internal drive 2 ■ disk3 – Specifies internal drive 3 ■ net, net0, net1, net2, net3 – Specifies the network interfaces ■ full path name – Specifies the de
APPENDIX C Installing the Servers With the Express Rail Rackmounting Kit This appendix provides instructions for installing the servers in an equipment rack with express (snap-in) rails. The wxpress rail rackmounting kit installs quickly, and does not require mounting screws or nuts. The kit and the installation procedures are the same for both the SPARC Enterprise T5140 and T5240 servers.
Slide Rail Assembly Notes for the Express Rail Rackmounting Kit The express rail rackmount kit has two slide rail assemblies. A slide rail assembly can be installed on either the right or left side of the rack. Each slide rail assembly consists of a three-section slide rail and a removable mounting bracket (FIGURE C-1).
■ The removable mounting bracket slides 14.5 in. (37 cm) out of the slide rail, then locks in place. If you unlock the mounting bracket at this point, it slides an additional 14.5 in. (37 cm) before separating from the slide rail. You can then mount the mounting bracket to the right or left side of the server chassis. ■ Note that there are a total of six locks (FIGURE C-2) in a slide rail assembly. Four are on the mounting bracket. Two locks are on the slide rail.
FIGURE C-2 70 Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise T5240 Server SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Installing the Servers in a Rack With Express Rails Note – Ensure that you have all of the parts in the rackmount kit before you begin the installation of the server. The rackmount kit contains two slide rail assemblies, which can be installed on either the right or left side of the rack. A slide rail assembly consists of two parts, a slide rail and a removable mounting bracket. The slide rail attaches to the rack posts. The mounting bracket attaches to the server chassis.
FIGURE C-3 Unlocking the Express Rail Slide Rail Assembly b. Pull the mounting bracket out until it stops.
c. Slide the mounting bracket release button to the left (FIGURE C-4), then slide the mounting bracket completely out of the slide rail.
2. Attach a mounting bracket to the right side of the server chassis. a. Position the mounting bracket against the chassis (FIGURE C-5). Ensure that the slide rail lock is at the front and the keyed openings on the mounting bracket are aligned with the locating pins on the side of the chassis. FIGURE C-5 Attaching an Express Rail Mounting Bracket to the Chassis b. Ensure that the heads of the four locating pins protrude through the keyed openings in the mounting bracket.
FIGURE C-6 Express Rail Slide Rails Orientation for Installation Appendix C Installing the Servers With the Express Rail Rackmounting Kit 75
5. Extend the slide rails (outer section) to fit the rack and attach the slide rails to the rack (FIGURE C-7). You hear an audible click when the rails securely attach to the rack. FIGURE C-7 Attaching Express Slide Rails to the Rack Caution – Deploy the antitilt feature on the rack before continuing the installation. ▼ To Insert and Lock the Server in the Rack 1. Deploy the antitilt feature, if the rack is so equipped.
Caution – The weight of the servers on extended slide rails can be enough to overturn an equipment rack. Caution – The 2U server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount the server into a rack enclosure when using the procedures in this chapter. 2. Insert the ends of the mounting brackets into the sliding rails (FIGURE C-8). 3. Slide the server approximately halfway into the chassis (FIGURE C-8).
4. Slide the green release tab (FIGURE C-9). 5. Push the server all the way into the rack until it locks into place (FIGURE C-9). FIGURE C-9 Sliding the Express Rail Release Tab and Securing the Server in the Rack Caution – Before continuing, verify that the server is securely mounted in the rack, and that the slide rails are locked in the mounting brackets.
Installing the Cable Management Arm The rackmounting kit for each server comes with the same cable management arm (CMA) assembly. The CMA installation procedures are the same for both servers. See “Installing the Cable Management Arm for Both Servers” on page 24. Connecting the Server Cables To boot the server, you must connect and configure the network and serial ports. For instructions, see “Connecting the Server Cables for Both Servers” on page 31.
80 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Index Symbols #.
installation instructions, optional components, reference, 3 installing mounting brackets, 71 IP address, 4 L LEDs, ports, and slots illustrated, 7, 8 left, 15 left and right sides defined, 15 levers, locking, See "slide rail assembly locks" locating pins for mounting brackets, 71 locations of ports, slots, and LEDs (illustration), 7, 8 locks, See "slide rail assembly locks" logging into service processor using network management port, 45, 50 using serial management port, 45 M map of OpenBoot PROM devices
T terms left and right sides, 15 slide rail assembly, 10, 68 TTYA serial port, 7 U uadmin command, 57 unlocking mounting bracket, 71 W web site http://manuals.fujitsu-siemens.
84 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008
Herausgegeben von / Published by Fujitsu Siemens Computers GmbH Bestell-Nr./ Order No.
