Datasheet
Data Sheet FUJITSU Server PRIMERGY TX2560 M1 Tower Server
Page 4 / 10 www.fujitsu.com/fts
Memory protection Advanced ECC
Memory Scrubbing
SDDC (Chipkill™)
Rank sparing memory support
Memory Mirroring support
Memory notes Memory Mirroring with identical modules in both channel pairs of a bank (4 modules per bank), Rank sparing or
Performance Mode with identical modules in all four channels (4 modules per bank).
Memory options 8 GB (1 module(s) 8 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133R, DIMM, 1Rx4
8 GB (1 module(s) 8 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133R, DIMM, 2Rx8
16 GB (1 module(s) 16 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133R, DIMM, 2Rx4
32 GB (1 module(s) 32 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133P, LRDIMM, 4Rx4
32 GB (1 module(s) 32 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133R, DIMM, 2Rx4
64 GB (1 module(s) 64 GB) DDR4, registered, ECC, 2,133 MHz, PC4-2133P, LRDIMM, 4Rx4
Memory modules notes 1536 GB memory expected to be available Q3/2015, current max. memory capacity 768 GB
Interfaces
USB 2.0 ports 4 x USB 2.0 (2x rear, 1x internal, 1x UFM internal boot device)
USB 3.0 ports 5 x USB 3.0 (2x rear, 1x internal for RDX drives, 2x front)
Graphics (15-pin) 2 x VGA (thereof 1x front optional)
Serial 1 (9-pin) 1 x serial RS-232-C optional, usable for iRMC S4 or system or shared
Management LAN (RJ45) 1 x dedicated management LAN port for iRMC S4 (10/100/1000 Mbit/s)
Management LAN trafc can be switched to shared onboard Gbit LAN port
Onboard or integrated Controller
RAID controller additional RAID controller options are described under Components RAID controller
SATA Controller Intel® C612, 1 x SATA connector for optical drive (ODD), 1x SATA connector for SATA-DOM
LAN Controller DynamicLoM based on Emulex XE100 series. Dynamic LoM connector cards are optional. The Controller Cards offer 2
LEDs 1) activity/connect (green) 2) speed (green/orange).
PXE-Boot via LAN from PXE server, iSCSI / FCoE boot (also diskless).
Intel® Ethernet Controller I210 supported (on project request only).
Remote management controller Integrated Remote Management Controller (iRMC S4, 256 MB attached memory incl. graphics controller)
IPMI 2.0 compatible
Trusted Platform Module (TPM) Inneon / separate module; TCG V1.2 compliant (option)
Slots
PCI-Express 3.0 x4 4 x Full height optional; slot 5+6 (CPU1, riser card); slot 11+12 (CPU2, riser card), 252mm length
PCI-Express 3.0 x8 5 x Full height ; slot 1 (CPU1, modular RAID, 167mm), slot 2 (CPU1, 167mm), opt. slot 4 (CPU1, opt. riser card, 252mm);
opt. slot 8 (CPU2, 167mm), opt. slot 10 (CPU2, opt. riser card, 252mm)
PCI-Express 3.0 x16 3 x Full height ; slot 3 (CPU1), slot 8+9 (CPU2), 167mm lenght; please be aware, optional riser cards occupies slot 3 / 9!
Slot Notes Slot 1: PCIe Gen3 x8 slot is dedicated for the modular RAID controller.
up to 5 PCIe Gen3 slots are supported with the rst processor, up to 10 PCIe Gen3 slots are supported with two
processors.
Onboard slots (Slot1, 2, 3 & 7, 8, 9) support card lenght of up to 167mm; Slots on the optional riser cards (4, 5, 6, 10,
11, 12) support card lenght of up to 252mm
Storage drive bays 3.5-inch or 2.5-inch hot-plug SAS/SATA
Accessible drive bays 3 x 5.25/1.6-inch
Notes accessible drives All possible options described in relevant system congurator.
Drive bays
Storage drive bays max. 12x 3.5” hot plug HDD + opt.2x2.5” NON hot plug HDD/SSD or max. 32x 2.5” hot plug HDD/SSD
Optional accessible drives up to 3x 5.25/1.6-inch bay for accessible devices (depending on the amount of storage drive bays)
Number of fans 3
Fan conguration redundant / single hot-plug (each fan can be exchanged separately)
Fan notes 2+1 redundant, huge 120mm fans with optimized fan geometry for silent and safe operation
Number of fans 3
Fan conguration 3x single hot plug fans Ø120mm (2+1 redundancy)