User’s Guide Learn how to use your Fujitsu LIFEBOOK T904 Tablet PC Guide d’utilisation Découvrez comment utiliser votre ordinateur portable Fujitsu LIFEBOOK T904
User’s Guide Learn how to use your Fujitsu LIFEBOOK T904 Tablet PC 1-
Copyright and Trademark Information Fujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LIFEBOOK are registered trademarks of Fujitsu Limited.
WARNING: HANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. USER GUIDE FOR WIRELESS BROADBAND CONNECTION IF YOU HAVE THE OPTIONAL WIRELESS WAN (WWAN) DEVICE INSTALLED IN YOUR TABLET PC, THE WWAN USER’S GUIDE IS LOCATED AT: http://solutions.us.fujitsu.
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Adapters with an output rating of 19 VDC, with a current of 4.22 A (80 W). + AC adapter output polarity: When using your Tablet PC equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • • • • The bottom of this Tablet PC computer can become hot when used for long periods of time.
Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.
Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Conventions Used in the Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 1 Getting to Know Your LIFEBOOK Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Locating the Controls and Connectors .
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Using the Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Touchpad/Active Digitizer/Touchscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Using the Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Digitizer Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2 Getting Started with Your LIFEBOOK Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Starting Your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boot Sequence . . . . . . . . . . . . . . . . . .
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Replicator Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information About Anytime USB Charge Utility. . . . . . . . . . . . . . . . . . . .
Restoring Your System Image and Software (Windows 8) . . . . . . . . . . . 110 Saving and Recovering Your Factory and System Images . . . . . . . . . . . . Backing Up a System Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recovery and Utility tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recovering your Factory Image using Recovery and Utility . . . . . . . . . . Changing BIOS settings between Windows 8 32-bit and 64-bit . . . . . .
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Popular Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Learning About Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B: Fingerprint Sensor Device Introducing the Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . . . . 166 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface About This Guide The LIFEBOOK T904 Tablet PC from Fujitsu America is a powerful convertible computer. It can be used either as a standard notebook using keyboard input, or in tablet configuration using pen input. It is powered by the new 3rd Generation Intel® Core™ Processor, has a built-in color display with a dual digitizer, and brings the computing power of desktop personal computers (PCs) to a portable and versatile environment.
THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY. THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR LIFEBOOK TABLET PC, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
Fujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com. Maintaining Latest Configuration To ensure that you always have the most current driver updates related to your system, you should occasionally access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available to allow you to download the latest drivers, utilities, and applications from the Fujitsu Support site.
Chapter 1 Getting to Know Your LIFEBOOK Overview This section describes the components of your Fujitsu LIFEBOOK T904 Tablet PC. We strongly recommend that you read it before using your Tablet PC – even if you are already familiar with notebook computers. Figure 1.
Locating the Controls and Connectors Connectors and peripheral interfaces on the LIFEBOOK T904 Tablet PC and the optional port replicator allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the LIFEBOOK T904 Tablet PC and/or optional port replicator. Each of the icons is either molded into or printed on the Tablet PC or port replicator chassis.
Connection Tablet PC Icon Purpose Security lock slot The security slot allows you to secure the Tablet PC using compatible locking devices. Suspend/ Resume slide The Suspend/Resume slide allows you to suspend Tablet PC activity without powering off, resume your Tablet PC from suspend mode, and power on the system when it has been shut down from Windows.
Optional Web Cam Web Cam Access LED Display Panel Status Indicator Panel Built-in Microphone Fingerprint Sensor Windows Button LIFEBOOK Security/ Tablet PC Buttons Power/Suspend/ Resume Slide Built-in Microphone Ambient Light Sensor Stereo Speaker Keyboard Status Indicator Panel Wireless Device On/Off Switch SD/SDHC/SDXC Card Slot Stereo Speaker Touchpad Cursor Control Figure 2.
Top Components The following is a brief description of your LIFEBOOK Tablet PC’s top components. Web Camera The optional FHD (1920 x 1080 pixel) digital web camera can be used to take pictures of yourself to send over the internet. Web Cam Access LED The web cam access LED indicates when the web camera is activated. Display Panel The display panel is a color LED panel with backlighting for the display of text and graphics.
Keyboard A full-size keyboard with dedicated Windows keys. See “Keyboard” on page 33. Dual Stereo Speakers The built-in dual speakers provide stereo sound. Touchpad Cursor Control The touchpad cursor control offers an additional method for moving the cursor. See “Touchpad/Active Digitizer/Touchscreen” on page 36. SD/SDHC/SDXC Card Slot The SD/SDHC/SDXC card slot allows you to install a Secure Digital (SD) card for data storage.
Air Vents DC Power Jack Smart Card Slot HDMI Port USB 3.0 Port with Anytime USB Charge External Video Port Headphone Jack Microphone Jack USB 3.0 Port Figure 3. LIFEBOOK Tablet PC left-side panel Left-Side Panel Components The following is a brief description of your LIFEBOOK Tablet PC’s left-side components. Air Vents The air vents are used to cool the system to prevent overheating.
Smart Card Slot A dedicated Smart Card slot is provided on your Tablet PC. Smart Cards are the same size and shape as a credit card, but they contain embedded integrated circuits. To use the embedded Smart Card Reader, you must purchase optional third-party software for installation. Headphone Jack The headphone jack allows you to connect headphones. See “Headphone Jack” on page 82. Microphone Jack The microphone jack allows you to connect an external stereo microphone. See “Microphone Jack” on page 82.
Modular Bay Device USB 2.0 Port Pen Tether Attachment Point Anti-theft Lock Slot Modular Bay Eject Lever Pen Garage Figure 4. LIFEBOOK Tablet PC right-side panel Right-Side Panel Components The following is a brief description of your LIFEBOOK Tablet PC’s right-side components. Modular Bay The Modular Bay can accommodate one of the following devices. See “Modular Bay Devices” on page 47. • • • • Modular Blu-ray™ RW Drive.
Pen Garage The pen garage is used to store the pen (also called a “stylus”) when not in use.The pen is used as the interface with the active digitizer display. Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device. Modular Bay Eject Lever The Modular Bay Eject Lever allows you to release the modular bay device so that it can be removed. See “Modular Bay Devices” on page 47.
Gigabit LAN (RJ-45) Jack USB 2.0 Port Figure 5. LIFEBOOK Tablet PC back panel Back Panel Components Following is a brief description of your LIFEBOOK Tablet PC’s back panel components. Gigabit LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for an internal Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. See “Internal LAN (RJ-45) Jack” on page 80. USB 2.0 Port The USB 2.0 port allows you to connect Universal Serial Bus devices. USB 2.
Air Vents (multiple locations) Memory Upgrade Compartment Cleanable Dust Filter Wireless WAN Module Compartment Battery Latch Battery Latch Port Replicator Connector Lithium ion Battery Figure 6. LIFEBOOK Tablet PC bottom panel Bottom Components The following is a brief description of your LIFEBOOK Tablet PC’s bottom panel components. Memory Upgrade Compartment Your Tablet PC comes with high speed Double Data Rate 3 Synchronous Dynamic RAM (DDR3 1600 MHz SDRAM).
Air Vents The air vents allow air to circulate through the system to cool down the components. TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO KEEP ALL AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
Power Indicator Battery 1 Level Battery Charging Optical/Hard Drive Access Battery 2 Level NumLk ScrLk CapsLk Security Figure 7. Status Indicator Panel Status Indicator Panel There are two Status Indicator Panels on your notebook: on the left front and under the display. The Status Indicator Panels display symbols and associated LEDs that correspond to specific components of your Tablet PC. These symbols tell you how each of those components is operating.
• Steady On (Blue): This means that there is power to your Tablet PC and that it is ready for use. • Flashing: This means that your Tablet PC is in Sleep mode. • Steady Off: This means that your system is either in Hibernate mode, or that your tablet has been turned off. If you are charging your battery, the Power indicator symbol will remain on even if your LIFEBOOK Tablet PC is shut off.
Hard Drive/Optical Drive Access Indicator The Hard Drive/Optical Drive Access indicator shows whether your internal hard drive or optical drive are being accessed is being accessed. Security Indicator The Security Indicator flashes (if a password was set) when the system resumes from Off or Sleep modes. You must enter the password that was set in the Security Panel before your system will resume operation.
Display Panel Figure 8. Opening the Display Panel Display Panel Your LIFEBOOK T904 Tablet PC contains an LED display panel that is backlit for easier viewing in bright environments. The convertible design of your Tablet PC allows you to open the display fully, rotate it in either direction 180 degrees, and lay it face up on the keyboard. This allows you to use the system as a tablet, much as you would a pad of paper.
Using the System as a Tablet If you would like to use the system as a tablet, perform the following steps. • THE DISPLAY CAN BE ROTATED IN EITHER DIRECTION, BUT WHEN RETURNING THE SYSTEM TO NOTEBOOK MODE, BE SURE TO TURN IT BACK TO ITS ORIGINAL POSITION (I.E., THE REVERSE OF HOW YOU TURNED IT WHEN YOU OPENED IT. TURNING THE DISPLAY IN THE INCORRECT DIRECTION COULD CAUSE HINGE DAMAGE.
Holding the Tablet PC • Your computer can be used in tablet configuration in four different orientations: 0o, 90o, 180o, and 270o. (Figure ). Letters associated with each orientation refer to the position of the system when the arrow is facing up. • (A) Portrait Orientation: Hold the system with the display positioned vertically with the web camera on the left. • (B) 2nd Portrait Orientation: Hold the system with the display positioned vertically with the web camera on the right.
When the system is in Pause state, there are several ways to enable it: • Go to the Start menu > All Programs > Auto Rotation Utility, and click Resume. • Right-click on the Auto Rotation Utility icon in the system tray and click Resume. • Open the Fujitsu Menu by pressing the [A] button or by clicking the Fujitsu Menu icon in the system tray, then clicking the [AutoRotation Resume] button on the second page of the Fujitsu Menu.
IF USING AC POWER, YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. IF USING BATTERY POWER, YOUR BRIGHTNESS SETTINGS IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT. THE HIGHER THE BRIGHTNESS LEVEL, THE MORE POWER THE TABLET PC WILL CONSUME AND THE FASTER YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE, MAKE SURE THAT THE BRIGHTNESS IS SET AS LOW AS POSSIBLE.
• To limit who can access the sensors, click Change who can access sensors, then check or uncheck the box adjacent to the individual you would like to grant or prohibit access. • To uninstall the sensor, click Uninstall this sensor. Windows 8: In Windows 8 systems, there are two ways to enable or disable the light sensor. 1. From the Modern Start Screen go to Change PC Settings -> General -> Screen. There you will find Adjust my screen brightness automatically.
Keyboard Function Keys Fn Key Start Key Numeric Keypad (surrounded by heavy line) Application Key Cursor Keys Figure 12. Keyboard Using the Keyboard Your Fujitsu LIFEBOOK Tablet PC has an integral 84-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys.
• Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. • Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. • Windows keys: These keys work with your Windows operating system.
Function Keys Your LIFEBOOK Tablet PC has 12 function keys, F1 through F12. Functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. • The [Fn] key provides extended functions for the Tablet PC and is always used in conjunction with another key. • [Fn+F2]: On backlit computers, pressing [F2] while holding [Fn] will toggle the backlit keyboard on (darker), on (brighter), and off.
Touchpad/Active Digitizer/Touchscreen Left Button Cursor Control Right Button Figure 13. Touchpad pointing device Using the Touchpad The touchpad is built into your LIFEBOOK Tablet PC. It is used to control the movement of the cursor to select items on your display panel. The touchpad is composed of a cursor control below the center of the keyboard and two buttons below it. The left button functions the same as a left mouse button while the right button has the same function as a right mouse button.
Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the touchpad once. Figure 14. Clicking with button Figure 15. Clicking with Touchpad Figure 16.
• IF THE INTERVAL BETWEEN CLICKS IS TOO LONG, THE DOUBLE-CLICK WILL NOT BE EXECUTED. • PARAMETERS FOR THE QUICK POINT CAN BE ADJUSTED FROM THE MOUSE DIALOG BOX LOCATED IN THE WINDOWS CONTROL PANEL. Dragging Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad.
• Pointers: This tab lets you set up the scheme for the cursor depending on its functionality. • Pointer Options: This tab lets you set up a relation between the speed of your finger motion and the speed of the cursor. It also allows you to enable a Pointer Trail for the cursor arrow. Active Digitizer Display NOTE: Your system has a capacitive touch panel that responds to finger touch and gestures. (This configuration is called a “Dual Digitizer”.
Right-Click Toggle Eraser Button Eraser Toggle Pen Tether Attachment Point Figure 22. Stylus Features • DO NOT USE EXCESSIVE FORCE WHEN TAPPING OR WRITING ON THE SCREEN WITH THE STYLUS. EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR ACTIVE DIGITIZER. • TO PURCHASE ADDITIONAL OR REPLACEMENT STYLUSES, VISIT THE FUJITSU ACCESSORIES WEBSITE AT: WWW.SHOPFUJITSU.COM.
Figure 23. Clicking on the Active Digitizer Display Figure 24. Right-clicking Active Digitizer Double-Clicking To double-click, touch the item twice, and then immediately remove the stylus tip (Figure 25). Figure 25.
Dragging Dragging means moving an item with the stylus by touching the screen, moving and then lifting the stylus. To drag, touch the Active Digitizer Display with your stylus on the item you wish to move. While continuing to touch the screen with the stylus, drag the item to its new location by moving the stylus across the screen, and then lifting the stylus to release it (Figure 26). Figure 26.
DO NOT USE EXCESSIVE FORCE WHEN TAPPING ON THE SCREEN DURING CALIBRATION. USE OF EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR TOUCH PANEL. Depending upon whether you are calibrating pen input or touch input, firmly touch the screen with the stylus or your finger directly on the (+) symbol. Lift the stylus or your finger from the screen and the target will move to a different location on the screen. 6 Repeat step 4 until you have selected all of the (+) symbols.
Scrolling Right/Left: To scroll right or left, slide two fingers right or left (Figure 27). Zooming In/Out: To zoom in or out on a page using the touchpad, place two fingers in a pinch position and open the pinch to zoom in, or close to zoom out (Figure 28). Toggling the charms To toggle the charm swipe one finger from the right edge of touch pad (Figure 29). Toggling the application commands bar To toggle the application commands bar swipe one finger down from the top edge of the touchpad (Figure 30).
. Installing a Pen Tether To prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system. To attach the pen tether to your Tablet PC, perform the following steps: Attach the end of the pen tether with the smaller loop to your pen. To do so, push the end of the tether through the hole in the pen, then thread the opposite end of the tether through the loop.
Volume Control Your Fujitsu LIFEBOOK Tablet PC has multiple volume controls which interact with each other. ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
Modular Bay Figure 33. Modular Bay Modular Bay Devices Your Fujitsu LIFEBOOK Tablet PC contains a Modular Bay. The Modular Bay can house an optical drive, a Lithium ion battery, and a weight saver. Your Modular Bay will have one of the following devices installed. • Modular Dual-Layer Multi-Format DVD Writer: This allows you to access movies, software, and audio DVD/CDs and record to DVD, CD, and DVD-RAM discs. • Modular Blu-ray™ RW Drive. This drive allows you to read from and write to Blu-ray discs.
Cold-swapping To cold-swap modular devices in your Modular Bay follow these easy steps: Close any open files and shut down your LifeBook notebook. 2 Pull out the Flexible Bay release latch. This will push your device out slightly, allowing you to remove it. 3 Slide your device out until it is clear of the bay. This will require light force. 4 Slide the device you are installing into your notebook until it clicks into place. 5 It is now safe to turn your notebook back on.
Power Button shown for reference only) Windows Button Figure 35. LIFEBOOK T90 Tablet PC Security/Tablet PC Buttons LIFEBOOK Security/Tablet PC/Windows Buttons A unique feature of your LIFEBOOK T904 Tablet PC is the array of Security and Tablet PC buttons as well as a standalone Windows button. These buttons allow you to secure your Tablet PC from unauthorized use and to launch specific applications and functions with the touch of a button.
Button Icon System State System is pre-boot or resuming from suspend Security Panel Function Security Button 1 Security Button 2 Security Button 3 Security Button 4 Security Enter Button Table 3.
Post-logon button functions All six buttons can be used after logging on. See Table 3 for information about each of the post-logon functions. Button Icon System State Tablet PC Function System is post-logon (Windows desktop is displayed) Windows Button has two functions. Primary action: opens up the Start menu [Windows] button + [Power] button: Opens up CTRL+ALT+DEL screen Volume Down Volume Up Pauses and resumes the rotation lock feature.
Volume Down/Volume Up Buttons The Volume Down and Volume Up buttons allow you to decrease and increase the volume. Rotation Lock The rotation lock feature is used to Pause or Resume the auto rotation feature. When the system is in tablet mode, if the auto rotation feature is resumed, the display rotates automatically when the system is rotated. When the auto rotation feature is paused, the display doesn't rotate automatically when the tablet is rotated.
Setting up LIFEBOOK Security Panel When you receive your Tablet PC, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords. Numbered Buttons Use these buttons to enter your password. Enter Button After entering the button strokes, push this button to enter the password into the Tablet PC. Passwords The user and supervisor password may be set on this Tablet PC.
• THE PURPOSE OF SUPERVISOR PASSWORD IS TO BE ABLE TO BYPASS THE USER PASSWORD IN CASE THE USER PASSWORD IS FORGOTTEN. THE SUPERVISOR PASSWORD ALONE WILL NOT LOCK THE SYSTEM. • YOU MUST SET THE SUPERVISOR AND USER PASSWORDS FOR THE SECURITY PANEL TO WORK. Setting Supervisor Password You must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password. 1 Windows 7: Go to the Start menu.
Using Your LIFEBOOK Security Panel The security lock feature is in effect both when the system resumes from Off or Hibernation state. You always need to push the Security Panel buttons to input the user password. Your system will not begin the boot sequence until you enter your supervisor/user password. From Off State Turn on your system. 2 When the Security Indicator flashes, enter the password and press Enter button (e.g.
Open the system Control Panel. If the display is in Category view, click one of the icon selections in the View by: field. Click on Power Options. 2 Click Choose what closing the lid does in the left pane. 3 Select the desired action for When I close the lid, then click the [Save changes] button. 1 Low Battery Operations If your Tablet PC has a low battery, pushing the suspend/resume slide only turns on the Security Indicator.
User: Go to Start -> Control Panel. 2 Open Programs and Features in the Control Panel. 3 Select Security Panel for User in the list, and click Uninstall/Change. 4 When User Account Control box appears, click Continue. 1 Supervisor: Go to Start -> Control Panel. 2 Open Add or Remove Programs Properties in the Control Panel. 3 Select the Security Panel for Supervisor in the list, and click Uninstall/Change. 4 When User Account Control box appears, click Continue.
Chapter 2 Getting Started with Your LIFEBOOK Power Sources Your Fujitsu LIFEBOOK Tablet PC has four possible power sources: a primary Lithium ion battery, a secondary modular bay battery, an AC adapter or an optional Auto/Airline adapter. Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your Tablet PC and charging the batteries. Connecting the AC Adapter 1 Plug the DC output cable into the DC power jack of your LIFEBOOK Tablet PC.
DC Power Jack AC Adapter Figure 36. Connecting the AC Adapter Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power Be sure that you have at least one charged battery installed. 2 Remove the AC adapter or the Auto/Airline adapter. 1 THE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT EITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR TABLET PC.
Starting Your LIFEBOOK Tablet PC Power On Power/Suspend/Resume Slide The Power and Suspend/Resume slide is used to power on your LIFEBOOK notebook, to resume from Sleep or Save-toDisk mode or to place your notebook in Sleep or Save-to-Disk mode. (You can also use the slide to power down the system by holding it for approximately five seconds. This can be useful if the system is “hung up”. This shouldn’t be used as the normal means of shutdown, however.
DO NOT CARRY YOUR LIFEBOOK TABLET PC AROUND WITH THE POWER ON OR SUBJECT IT TO SHOCKS OR VIBRATION, AS YOU RISK DAMAGING YOUR TABLET PC. When you power on your LIFEBOOK, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LIFEBOOK Tablet PC will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 99.
Hard Disk Drive Passwords To provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility. REMEMBER YOUR PASSWORDS. IF YOU SET AND FORGET YOUR USER AND MASTER HARD DISK PASSWORDS, FUJITSU AMERICA WILL NOT BE ABLE TO RESET IT. YOU MAY LOSE DATA AND HAVE TO REPLACE YOUR SYSTEM BOARD OR HARD DISK DRIVE.
Booting the System We strongly recommend that you not attach any external devices or put a DVD/CD in your drive until you have gone through the initial power on sequence. When you turn on your LIFEBOOK notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.
Select the applications you wish to install by selecting the checkbox adjacent to your selection, or click [Select All] if you would like to install all available applications. Once you have made your selections, click [Install]. Note that in some cases (depending upon which application was selected for installation) after installation completes, the system will prompt you to reboot.
Power Management Your LIFEBOOK Tablet PC has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your LIFEBOOK Tablet PC may be controlled from settings made in your operating system.
• Clicking the power icon on the lock menu. • Selecting Sleep from the [Settings]->[Power] menu. • Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition. Your Tablet PC’s system memory typically stores the files on which you are working, open application information, and any other data required to support the operations in progress. When you resume operation from Sleep mode, your Tablet PC will return to the point where it left off.
Hibernation (Save-to-Disk) Feature The Hibernation feature saves the contents of your Tablet PC’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature To enable or disable the Hibernation feature follow these steps: From the Modern Start screen, press [Windows]+[X].Select Control Panel from the menu, then select Power Options.
Power Off Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your Tablet PC shuts down without error, use the Windows shut down procedure. • ALWAYS POWER OFF THE COMPUTER BEFORE TRANSPORTING AND/OR PACKAGING IT. AFTER SHUTTING DOWN THE SYSTEM, WAIT UNTIL THE STATUS LED PANEL INDICATES POWER OFF CONDITION (I.E., NO LIGHTS ARE ILLUMINATED).
ENERGY STAR® Compliance Your Fujitsu system is an ENERGY STAR qualified mobile PC. By choosing a computer with the latest energy-saving technology, you’re helping to preserve our environment for future generations. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency, U.S. Department of Energy, Natural Resources Canada, and other governments around the world helping us save money while protecting the environment through energy efficient products and practices.
Chapter 3 User-Installable Features Lithium ion Battery Your LIFEBOOK Tablet PC has a Lithium ion battery that provides power for operating your Tablet PC when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.
• ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. OPTICAL DRIVE OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE. • UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING THEM IN THE TRASH.
USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT CHARGING COMPLETELY. Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your Tablet PC will go into Sleep mode. There is no guarantee that your data will be saved once the Tablet PC reaches this point.
Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping: Cold-swapping Batteries To cold-swap batteries in your battery bay, follow these easy steps: 1 2 3 4 5 6 Have a charged battery ready to install. Shut down your Tablet PC and disconnect the AC adapter. Turn the system upside down and orient it as shown in Figure 38.
s Battery release latch Battery lock Battery pack Figure 38. Unlatching a Battery Figure 39.
SD Card Figure 40. Installing an SD Card Secure Digital Cards Your LIFEBOOK Tablet PC supports Secure Digital (SD), Secure Digital High Capacity (SDHC), and Secure Digital eXtended Capacity (SDXC) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.
Installing SD Cards SD Cards are installed in the SD Card slot. To install an SD Card, follow these steps: INSTALLING OR REMOVING AN SD CARD DURING YOUR LIFEBOOK TABLET PC’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK TABLET PC. DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR LIFEBOOK TABLET PC, OR BOTH. See your specific card manual for instructions on the installation of your card.
Memory Upgrade Module Your Fujitsu LIFEBOOK Tablet PC comes with a minimum of 2GB of high speed Double Data Rate Synchronous Dynamic RAM (DDR3-1600 SDRAM) factory installed. To increase your Tablet PC’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com.
Figure 41. Opening Memory Compartment Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You’ll hear a click when it is properly in place. 8 Replace the cover and reinstall the screws. 7 THE MEMORY UPGRADE MODULE IS NOT SOMETHING YOU ROUTINELY REMOVE FROM YOUR TABLET PC. ONCE IT IS INSTALLED, YOU CAN LEAVE IT IN PLACE UNLESS YOU WANT TO CHANGE SYSTEM MEMORY CAPACITY.
Removing a Memory Upgrade Module 1 Perform steps 1 through 4 of Installing a Memory Upgrade Module. 2 Pull the clips sideways away from each side of the memory upgrade module at the same time. 3 While holding the clips out, remove the module by lifting it up and pulling it away from your Tablet PC. 4 Store the memory upgrade module in a static guarded sleeve. 5 Replace the cover and reinstall the screws. Figure 43.
Device Ports Your Fujitsu LIFEBOOK Tablet PC and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Internal LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for a Gigabit (10BaseT/100Base-Tx/1000Base-T) Ethernet LAN connection. You may need to configure your Tablet PC to work with your particular network. (Please refer to your network administrator for information on your network configuration.
Universal Serial Bus Ports The Universal Serial Bus ports (USB) allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. There are four USB ports on your Tablet PC; on the left-hand side are two USB 3.0 ports, one of which is an Anytime USB Charge port (See “Information About Anytime USB Charge Utility.” on page 82) and there are USB 2.0 ports on the right side and rear.
Information About Anytime USB Charge Utility. The Anytime USB Charge feature can be disabled and enabled from the BIOS Setup Utility; the feature is enabled by default. The settings for the Anytime USB Charge feature can be changed by performing the following steps. Windows 7: Start > All Programs > Anytime USB Charge Utility and clicking on Settings. Windows 8: Go to Modern Start screen and right-click. Select All Apps and select Anytime USB charge utility.
HDMI Port. The High-Definition Multimedia Interface (HDMI) port is a digital audio/video interface over which uncompressed streams can be transmitted. HDMI is used to connect compatible digital devices with your computer (such as bigscreen TVs and video recorders). To connect an HDMI device: Align the connector with the port opening. 2 Push the connector into the port until it is seated. 1 Figure 46.
Port Replicator The port replicator extends the functionality of your LIFEBOOK® Tablet PC by providing ports to connect an external VGA monitor, a LAN (RJ-45) cable, four USB 3.0 devices, a DVI device, a DisplayPort device, headphones, and DC power. The port replicator connects to the bottom of your LIFEBOOK Tablet PC. Docking Connector Power Button Moveable Bar Latch/Unlatch Button USB 3.0 Ports (Qty.
Port Replicator Components The following is a brief description of the port replicator’s back panel components. (Figure 48) Power Slide The power slide allows you to power the port replicator on and off. Docking Connector The docking connector allows you to connect the Port Replicator to your LIFEBOOK Tablet PC. THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
USB 3.0 Ports (Qty. 4) Universal Serial Bus (USB) 3.0 ports allow you to connect USB devices. USB 3.0 ports are backward-compatible with USB 2.0 and 1.1 devices. Moveable Bar Latch/Unlatch Button The moveable bar latch/unlatch button allows you to adjust the moveable bar in order to align your system so that it aligns properly with the port replicator connector. Viewing the port replicator from the front, the moveable bar should be moved as far to the left side of the port replicator as possible.
Attaching the Port Replicator To attach the Port Replicator, align the Port Replicator connector on the bottom of your Tablet PC with the connector on the Port Replicator and push the corners down simultaneously. (Figure 49) Detaching Port Replicator To detach the Port Replicator: Pull the Port Replicator’s release latch away from the Port Replicator to release it from your Tablet PC. (Figure 50) 2 Lift the Tablet PC away from the Port Replicator to detach it. (Figure 51) 1 Docking Connector Figure 49.
Chapter 4 Troubleshooting Your LIFEBOOK Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE. If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8FUJITSU (1-800-838-5487) Web site: http://solutions.us.fujitsu.com/www/content/support/contact/index.php.
Specific Problems Using the Troubleshooting Table When you have problems with your LIFEBOOK Tablet PC, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your Tablet PC.
Problem Audio Problems There is no sound coming from the built-in speaker. Possible Cause Possible Solutions The volume is turned too low. Adjust the volume control on your Tablet PC and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC. The software volume control is set too low. Manually adjusting the volume (i.e.
Problem Possible Cause Possible Solutions LIFEBOOK Tablet PC fails to recognize DVD/CDRW/CD-ROM’s. (continued) Wrong drive designator was used for the disc in the application. Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designations are automatically adjusted.
Problem You have installed an external keyboard or mouse, and it does not seem to work. You have connected an external keyboard or a mouse and it seems to be locking up the system. Possible Cause Possible Solutions Your application has locked out your keyboard. Try to use your integrated pointing device to restart your system. Your external device is not properly installed. Re-install your device. See “Device Ports” on page 80.
Problem Power Failures You turn on your LIFEBOOK Tablet PC and nothing seems to happen. Your LIFEBOOK Tablet PC turns off all by itself. Possible Cause Possible Solutions The installed battery is completely discharged or there is no power adapter installed. Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 24. Install a charged battery or a Power adapter. The battery is installed but is faulty.
Problem Your LIFEBOOK Tablet PC turns off all by itself. (continued) Your LIFEBOOK Tablet PC will not work on battery alone. The battery seems to discharge too quickly. Possible Cause Possible Solutions You have a battery failure. Verify the condition of the battery using the Status Indicator panel. If the battery is shorted, replace or remove it. See “Status Indicator Panel” on page 24. Your power adapter has failed or lost its power source.
Problem Possible Cause Shutdown and Startup Problems The Suspend/Resume slide does not work. Possible Solutions Suspend/Resume slide is disabled. To enable the button, go to the Control Panel -> Power Options Properties and click the Advanced tab. In the Power buttons area, select “Change what the power button does” . There may be application software. conflict Close all applications and try the button again. The boot sequence settings of the setup utility are not compatible with your configuration.
Problem Video Problems The built-in display is blank when you turn on your LIFEBOOK Tablet PC. Possible Cause Possible Solutions The Tablet PC is set for an external monitor only. Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.
Problem Possible Cause Possible Solutions The display does not close. A foreign object, such as a paper clip, is stuck between the display and keyboard. Remove all foreign objects from the keyboard. The display has bright or dark spots. If the spots are very tiny and few in number, this is normal for a large LCD display. This is normal; do nothing. If the spots are numerous or large enough to interfere with your operation needs. Display is faulty; contact your support representative.
Power On Self Test Messages The following is a list of error-and-status messages that the Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check the operating system documentation on screen and in the manual. If you can find no reference to the message, contact a support representative. *Invalid NVRAM Data Problem with NVRAM access.
Restoring Your System Image and Software (Windows 7) Equivalent information for Windows 8 configurations can be found at “Restoring Your System Image and Software (Windows 8)” on page 110 It is very important that you create DVD copies of your Factory Image and Bootable Disc (along with other applicable media such as application discs) before beginning to use your system.
To make a copy of the Factory Image to DVD discs, you will need several blank discs (DVD-R or DVD+R discs are recommended) to create the copy. After creating the copy, be sure to label the discs and keep them in a safe place to ensure they do not get damaged. Creating Backup Images of Factory Image and Discs • SOME CONFIGURATIONS OF CERTAIN STYLISTIC MODELS DO NOT HAVE APPLICATIONS LOADED ON THE HARD DRIVE; RATHER, THEY ARE AVAILABLE AT THE FUJITSU SUPPORT SITE FOR DOWNLOAD.
Recovering Your Factory Image In the event you need to restore your original Factory Image, perform the following steps. Note that there may be some third-party applications that need to be installed from the application media bundled with your system. ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED. In order to recover your Factory Image, perform the steps outlined in “Running Recovery and Utility from hard disk”.
Figure 52. MyRecovery screen Click the [Next] button and the system will reboot. 5 After rebooting, the “Creating of the backup image” window appears, in which you can either click [Create the image on D drive] or [Select the drive] if you want to save to an external hard disk drive. (Note that the [Create the image on D drive may not be available on all configurations.) 6 An image appears showing you graphically how the image will be stored. Click the [Next] button. 7 Click [Execute] to start the backup.
Managing Your Backup Images With the MyRecovery tool you can also make copies of backup images, archive them on DVD, or delete them from your hard drive. 1 2 3 4 5 6 7 To begin, click the [MyRecovery] icon on your desktop. Click the [Manage/Create] button in the MyRecovery window. When the MyRecovery Manager window appears, click [Manage Backup Images]. In the next window, a list of your backup images appears.
Determining whether Recovery and Utility is pre-loaded Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. The Boot Menu will appear. 2 Press the Tab key to select Application menu. 3 Check whether the option is present. If it is not present, it means that the utility must be used from the disc. Proceed to “Running Recovery and Utility from the Bootable Disc” if is unavailable.
4 5 6 7 8 9 Click [OK]. While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen. When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next]. When the Operating System dialog appears, click [Next]. If necessary, enter your password, then click [OK]. When System Recovery Options window appears, click on Recovery and Utility.
Using Windows 7 Recovery DVD on Windows 8 64-bit system (downgrade option). When using the Windows 7 Recovery DVD on a system that was supplied with Windows 8 x64 pre-installed, you should first deactivate Secure Boot and activate CSM and Fast Boot using the following procedure: To access the BIOS Setup, press the [F2] key after switching on the system. 2 Use right/left arrow keys to switch to the "Security" page.
When the Operating System dialog appears, click [Next]. 7 If necessary, enter your password, then click [OK]. 8 When System Recovery Options window appears, click on Recovery and Utility. 9 Click the Recovery tab in the Recovery and Utility window, then click Restoring the Factory Image icon. 10 Click [Execute]. 11 Read the precautions, then select “I Agree”. 12 Click [Next], then click [Execute] to start the recovery process. 13 “1. Recovery Disc Check” will be in bold and the rest will be grayed out.
18 If you select to insert Application Disc, after copying of application disc(s) to hidden partition is completed, the message will appear again. Repeat inserting application disc(s) until all discs have been copied, then click [Skip] to continue with Restore. 19 After clicking [Skip], a confirmation message will appear "If you want to skip copying or you have finished copying, click [OK]. Click [Cancel] to go back to Restoring Factory Image to hidden partition.
Restoring Your System Image and Software (Windows 8) Equivalent information for Windows 7 configurations can be found at “Restoring Your System Image and Software (Windows 7)” on page 100 It is very important that you create DVD copies of your Factory Image and Bootable Disc before beginning to use your system. To do so, follow the instructions in the “Saving Your Factory Image” and “Creating Backup Images of Factory Image and Discs” sections of this chapter.
To make a copy of the Factory Image to DVD discs, you will need four or five blank discs (DVD-R or DVD+R discs are recommended) to create the copy. After creating the copy, be sure to label the discs and keep them in a safe place to ensure they do not get damaged. Creating Backup Images of Factory Image and Bootable Disc Using the [Manage/Change] button, you can create backup images of the Factory Image and/or Bootable Disc.
Recovering Your Factory Image. In the event you need to restore your original Factory Image, perform the following steps. ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED. In order to recover your Factory Image, perform the steps outlined in “Running Recovery and Utility from hard disk”. Backing Up a System Image Optional Step: Launch the Fujitsu Bonus Apps utility from your desktop, and select the components you wish to install.
6 7 8 9 10 On the “Step 2: Name your backup images” screen that appears, you can enter up to 300 characters of information about the backup file. This information will help you to identify the image at a later date. On “Step 3: Backup the entire C: drive image” verify your backup settings and click [Next]. Click [OK] on “Step 4: Please confirm the following before starting your backup” to restart you computer and begin backup. After backup completes and the system restarts, “Step 5: Backup Completed.
Selecting “Delete” option a. On “Step 1: Please select your target data” screen select location of a backup file. A list of backup files will appear. Select the file(s) you wish to delete and click [Next]. b. Click [Start] on “Step 2: Delete backup data” screen. c. Click [OK] to the confirmation message. d. Click [Finish] on “Step 4: Delete process has been completed” screen. Selecting “Add Comment” option a. On the “Step 1: Select target data” screen select location of a backup file.
Using the Recovery and Utility Tools The Recovery and Utility tools consist of a variety of tools that will help you recover your Factory Image, recover system images, and delete the data from your hard disk. Methods for accessing the utilities Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or they can be accessed by using the bootable disc. Please note that you can delete Recovery and Utility tools from your hard disk drive if you modify the partitions.
Insert the bootable disc into the drive tray. 4 Click [OK]. NOTE: In the following step, the Fujitsu logo screen may appear on the display for a couple of minutes before the progress bar appears. 3 5 Select CD/DVD boot mode: UEFI Mode) and press [Enter]. While the files are being loaded from the disc, the Fujitsu logo screen will appear followed by a progress bar screen at the bottom of the screen. Recovery and Utility tools Diagnostics tool: The Diagnostics tool is designed for use by IT professionals.
To recover from D: drive or external storage device: 1 Click [User System Backups] 2 The progress bar screen is followed by EULA screen. Click [Agree] to accept the EULA. 3 On “Select an image to restore” screen select the image to restore from the list of images and click [Next]. 4 Click [Start] on the “Confirm before restoration” screen to begin the restoration process. 5 Once restoration finishes, click [Close] in the “Finished restoration” screen; the computer will restart to Windows.
To delete hard disk data: a. Click the [Hard Disk Data Delete] button b. The progress bar appears, followed by the EULA screen. c. Agree to the EULA and click [Next]. d. Choose the hard disk from which the data should be deleted in the list of hard disks and click [Next]. • The Partition Creation utility is used to change the C: and D: drive partition sizes. To run this utility: a. Click the [Partition Creation] button. b. A progress bar screen appears, followed by the EULA screen. Agree to the EULA. c.
11 The Checking for Recovery Disk screen appears followed by the prompt to insert the first disk. Click [OK] to 12 13 14 15 16 continue. Repeat this step for all disks. After all recovery disks have been checked and the check has been completed, click [Next] Reinsert the first recovery disk and click [Next] Click [OK] when you receive the final warning informing you that all data on drives C: and D: will be lost. This starts the recovery process.
2 3 4 5 6 7 8 9 Use the right/left arrow keys to switch to the Security page. * If your system doesn't have Supervisor Password, you cannot change the Secure Boot Configurations. In this case you need to select Set Supervisor Password and set the password. Use the up/down arrow keys to select Secure Boot Configurations. Select Secure Boot or Secure Boot Option and using the [Enter] key set it to [Disabled] for 32-bit and to [Enabled] for 64-bit, then use the [ESC] key to exit Secure Boot Configurations.
Chapter 5 Care and Maintenance Caring for your LIFEBOOK Tablet PC If you use your Fujitsu LIFEBOOK Tablet PC carefully, you will increase its life and reliability. This section provides some tips for looking after the Tablet PC and its devices. THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
• Keep it away from food and beverages. • To protect your Tablet PC from damage and to optimize system performance, be sure to keep all air vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. • Do not operate the Tablet PC in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion. • If you accidentally spill liquid on your LIFEBOOK Tablet PC: 1 Turn it off.
Cleaning guidelines using recommended off-the-shelf cleaners Computer exterior, computer keyboard / To clean the exterior and keyboard, use one of the following off-the-shelf products: • Office Depot® #154-616 Notebook Cleaning Kit • Meridrew Enterprises Klear Screen® Wipes • 3M CL563 Cleaner Wipes Note: After cleaning with one of these products, gently polish with a dry, soft, lint-free cloth until the solution is no longer visible.
Cleaning the dust filter Your LIFEBOOK is equipped with fans to make air flow inside by pulling in outside air to cool the inside of the system. Depending on the environment in which the system is used, dust and dirt may be pulled in along with the air. Accumulated dust and dirt could impair the function of the system. • REMOVE AC ADAPTER: BEFORE REMOVING THE FILTER, TURN OFF THE SYSTEM AND PERIPHERALS AND DISCONNECT THE AC ADAPTER.
ALWAYS BE SURE THE DUST FILTER IS INSTALLED WHEN RUNNING YOUR SYSTEM. NOT USING THE FILTER COULD CAUSE CONTAMINATION AND POSSIBLE DAMAGE TO THE SYSTEM. Storing your LIFEBOOK Tablet PC • If storing your Tablet PC for a month or longer, turn it off, fully charge the battery, then remove and store all Lithium ion batteries. • Store the Tablet PC and batteries separately. If you store your tablet with a battery installed, the battery will discharge, and battery life will be reduced.
• Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.
Increasing Battery Life • Power your Tablet PC through the AC or optional auto/airline adapter whenever possible. • If your Tablet PC is running on battery power all day, connect it to the AC adapter overnight to recharge the battery. • Keep brightness to the lowest level comfortable. • Set the power management for maximum battery life. • Put your Tablet PC in Sleep mode when it is turned on and you are not actually using it. • Limit your media drive access.
Caring for your Optical Drive Your optical drive is durable but you must treat it with care. Please pay attention to the following points: • The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on. • Avoid using or storing the drive where it will be exposed to extreme temperatures. • Avoid using or storing the drive where it is damp or dusty.
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LIFEBOOK Tablet PC. Specifications of particular configurations will vary. Microprocessor New 3rd Generation Intel® Core™ Processor family. (Refer to system label to determine your processor.) Chipset • Mobile Intel® QM77 Express • Platform Control Hub (PCH) Memory System Memory • DDR3-1600 MHz SDRAM dual-channel memory module.
Video Built-in color flat-panel TFT active matrix LED backlit display with simultaneous display capability. Video Color and Resolution 13.
• • • • • • BTO 2.5" 7mmH/9.
LIFEBOOK Security/Tablet PC Panel See “LIFEBOOK Security/Tablet PC/Windows Buttons” on page 49. Trusted Platform Module The LIFEBOOK T904 has a Trusted Platform Module (TPM) installed for added system security. Theft Prevention Lock Lock slots for use with security restraint systems.
• • • • • One DC-in connector One DVI-D connector One DisplayPort connector One Headphone connector Docking connector (100-pin, to dock with system) Keyboard Built-in keyboard with all functions of 101 key keyboard. • • • • • • • • • Total number of keys: 84 Function keys: F1 through F12, plus Fn extension key Two Windows keys: one Start key, one application key Key pitch: 19 mm; key stroke: 1.7 mm (Note: On backlit keyboards, the stroke is 1.
Dimensions and Weight Overall Dimensions With foot and 6-cell main battery: 13.15"(w) x 9.60"(d) x 1.28” (h) (334 mm x 244 mm x 32.6 mm) Without foot, with 6-cell main battery: 13.15"(w) x 9.60"(d) x 1.06/1.22”(h) (334 mm x 244 mm x 26.8/31.0 mm) Weight With weight saver: Approximately 4.11 lbs. (1.86 kg) With optical drive: Approximately 4.41 lbs. (1.99 kg) With bay battery: Approximately 4.67 lbs. (2.12 kg) Environmental Requirements Temperature Operating: 41° to 95° F (5° to 35° C).
Pre-Installed Software Depending on your operating system, your Tablet PC comes with pre-installed software for playing audio and video files of various formats. In addition, there is virus protection software and applications that can bring additional value during your daily use of the system. Some software is pre-installed while other apps are a part of Fujitsu Bonus Apps • THE FOLLOWING LIST CONSTITUTES THE SOFTWARE THAT MAY BE INSTALLED ON YOUR COMPUTER.
Manuals Included with your Tablet PC you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included are available online through the software’s “Help” menu. We recommend that you review these manuals for information on the use of these applications. Adobe Reader Adobe Reader allows you to view, navigate, and print PDF files across all major computing platforms.
Skype for Windows 7 Skype for Windows 7 allows users to communicate with peers by Internet voice, video, and instant messaging. Skype can be used to place phone calls on traditional telephone networks. Calls to other users within Skype are free, while calls to landlines and cell phones are charged via a user account system. Skype is also popular for file transfer and teleconferencing.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your system. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LIFEBOOK Tablet PC. BIOS Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LIFEBOOK Tablet PC when you turn it on until it loads your installed operating system from disk.
CD-ROM Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading. Channel Range of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.
DHCP Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client. DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media. Disk Drive The hardware which spins the disk and has the heads and control circuitry for reading and writing the data. DMA Direct Memory Access.
Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment. ECP Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices. Encryption Key (Network Key) Data encryption key used to encrypt message text and for computing message integrity checks.
I/O Port The connector and associated circuits for data entering and leaving your computer in electronic form. IDE Intelligent Drive Electronics. A type of control interface for a hard drive that is inside the hard drive unit. IEEE802.11a Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11b Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band. IEEE802.
Within an isolated network, you can assign IP addresses at random as long as each one is unique. However, connecting a private network to the Internet requires using registered IP addresses (called Internet addresses) to avoid duplicates. The four numbers in an IP address are used in different ways to identify a particular network and a host on that network. Three regional Internet registries -- ARIN, RIPE NCC and APNIC -- assign Internet addresses from the following three classes.
MAC Address Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address. MB Megabyte. One million bytes.
MTU Maximum Transmission Unit The maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large. Network key Data that is used for encrypting data in data communication.
Peripheral Device A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM. Pitch (keyboard) The distance between the centers of the letter keys of a keyboard. Pixel The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear. POST Power On Self Test.
RAM Random Access Memory. A hardware component of your LIFEBOOK Tablet PC that holds binary information (both program and data) as long as it has the proper power applied to it. RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools. Reset The act of reloading the operating system. A reset erases all information stored in RAM. Resume To proceed after interruption.
SSID Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID.
TFT Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. UL Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices. USB Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer. VRAM Video Random Access Memory.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
This device must not be co-located or operated in conjunction with any other antenna or transmitter. For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral. Federal Communications Commission statement This device complies with Part 15 of FCC Rules.
Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
Before Using the Optional Wireless LAN This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure its correct operation. Keep this manual in a safe place for future reference.
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).
How to Handle This Device The WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. • The Wireless LAN devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n. • The WLAN devices operate in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.
Deactivation Using the Wireless On/Off Switch The WLAN device can be deactivated quickly and efficiently by toggling the Wireless Device On/Off Switch to the Off position. The switch has no effect on non-Wireless LAN models. Wireless Device Switch Figure 56. Wireless Device On/Off Switch Location Disconnection Using the Icon in the Taskbar Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.
Configuring the Wireless LAN The WLAN device can be configured to establish wireless network connectivity using the software that is built into the operating system. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: 1 2 3 4 5 6 From the Modern Start screen, press [Windows]+[X], then select Control Panel from the menu.
Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table.
Problem Unavailable network connection (continued) Possible Cause Possible Solution RF interference from Access Points or other wireless networks The use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device. Wireless network authentication has failed Re-check your Network Authentication, Encryption, and Security settings.
WLAN Specifications Specifications Item Specification Type of network The integrated Intel Dual Band Wireless-N 7260 device conforms to IEEE 802.11a, 802.11b/g, and 802.11n, Wi-Fi based*. Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined) Active frequency Typical operating distances** Number of channels • • • • • • • • • • 802.11n: 2.4 GHz or 5 GHz 802.11b/g: 2400~2473 MHz 802.11a: 4900 ~ 5850 MHz 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft.
Using the Bluetooth Device The Integrated Bluetooth module is a wireless device installed in selected Fujitsu mobile computers. What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter. Canadian Notice To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.
Appendix B: Fingerprint Sensor Device Introducing the Fingerprint Sensor Device Your system has a fingerprint sensor device at the bottom left below the display screen. Fingerprint Sensor Device Figure 57.
The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and online passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop.
• Windows XP Professional operating system or later • At least 35 MB available hard disk space Installing the OmniPass Application If OmniPass is already installed on your system, go to “User Enrollment” on page 169. Otherwise continue with this section on software installation. • INSTALLATION OF THE APPLICATION REQUIRES THAT YOU HAVE AN EXTERNAL OPTICAL DRIVE ATTACHED TO YOUR SYSTEM. • FOR INSTALLATION, OMNIPASS REQUIRES THAT THE USER INSTALLING OMNIPASS HAVE ADMINISTRATIVE PRIVILEGES TO THE SYSTEM.
Windows 8: From the Modern Start screen, right-click and select "All Apps", then select Control Panel. Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed, or, Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center. 2 Version information is listed on the left side of OmniPass Control center window.
During user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account.
Enter the password you use to log in to Windows. This becomes the “master password” for this OmniPass user. In most cases, the Domain: value will be your Windows computer name. In a corporate environment, or when accessing corporate resources, Domain: may not be your Windows computer name. Click [Next] to continue. 3 In this step OmniPass captures your fingerprint. See “Enrolling a Fingerprint” on page 171 for more information.
Once OmniPass has successfully acquired the fingerprint, the Verify Fingerprint screen will automatically appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Verification Successful under the capture window.
The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unselected authentication method, the authentication prompt associated with that method is displayed.
Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate. THIS SETTING IS MORE CONVENIENT IN THAT WHENEVER YOU GO TO A SITE REMEMBERED WITH THIS SETTING, YOU WILL BYPASS ANY AUTHENTICATION PROCEDURE AND GAIN INSTANT ACCESS TO THE SITE.
IF A MACHINE IS LOCKED AND OMNIPASS DETECTS A DIFFERENT USER LOGGING BACK IN WITH A FINGERPRINT, THE FIRST USER WILL BE LOGGED OUT AND THE SECOND USER LOGGED IN. Password Management OmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vault Management; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Passwords under Vault Settings.
To create and manage identities, double-click the OmniPass key in the system tray. Click Vault Management; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass user To add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply].
Configuring OmniPass This section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing Users YOU CANNOT IMPORT A USER INTO OMNIPASS IF THERE ALREADY IS A USER WITH THE SAME NAME ENROLLED IN OMNIPASS. Using OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user.
Importing an OmniPass User Profile To import an OmniPass user open the OmniPass Control Center, and click Run User Management Wizard. Click Restore a user's OmniPass profile. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user.
Troubleshooting You cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and password Cannot add Windows users to OmniPass If you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local security settings.
If you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password. Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.
Appendix C: Using Intel® Wireless Display Using the Wireless Display technology Intel® Wireless Display (WiDi) is a new technology that is available as an option on selected Fujitsu LIFEBOOK computers. If you have Intel WiDi on your system, please read these instructions and information regarding its use. Intel WiDi lets users enjoy and share PC content from an Intel® Core™ processor-based notebook with their big screen TV.
• IF YOU PURCHASED A SYSTEM WITH AN INTEL WIRELESS LAN AND OPTIONAL INTEL WIDI TECHNOLOGY, THE WIDI APPLICATION MAY OR MAY NOT BE PRE-INSTALLED (DEPENDING UPOON YOUR SYSTEM CONFIGURATION). SYSTEMS WITH INTEL WIDI PRE-INSTALLED WILL HAVE A WIDI ICON LOCATED ON THEIR DESKTOP. IF THE ICON IS NOT PRESENT, INTEL WIDI CAN BE DOWNLOADED FROM THE FUJITSU SUPPORT WEBSITE. • • • • THE INTEL WIDI TECHNOLOGY WILL ONLY WORK IN COMBINATION WITH AN INTEL WIRELESS LAN.
Index Battery Latches 23 BIOS 62 Bluetooth 164 Built-in Speakers 91 Button Icons 50 A About This Guide 1, 8 AC adapter 58 plug adapters 126 Active Digitizer 39 Air Vents 23 Anti-theft lock slot 21 Auto/Airline Adapter 58, 59 C Capacitive Touchscreen 43 CapsLock 26 Cold-swapping 48 Contact Information 9 Controls and Connectors 12 Conventions Used in the Guide 8 Cursor Keys 34 B Battery 70 care 126 cold-swapping 73 conserving power 65 dead 95 faulty 95 hot-swapping 73 increasing life 127 level indicator 25
E H Error Messages 99 External Video Port 13, 22, 83 Hard Disk Drive access indicator 26 problems 92 HDMI Port 17 Headphone Jack 12, 18, 82 Hibernation Feature 67 F Fingerprint Sensor Device 17, 166 enrolling a fingerprint 171 getting started 167 installing OmniPass 167 logging into a remembered site 174 OmniPass authentication toolbar 172 password replacement 172 remembering a password 173 uninstalling OmniPass 169 user enrollment 169 using OmniPass 172 Fujitsu Contact Information 9 Function Key F10 35
detaching 87 problems 92 Post-logon button functions 51 Power AC adapter 58 Auto/Airline adapter 58 failure 94 indicator 24 management 65 off 68 on 60 problems 96 sources 58 Power On Self Test 61, 99 Power/Suspend/Resume button 60, 65 Power/Suspend/Resume Slide 15 Pre-Installed Software 135 Adobe Acrobat Reader 136 Google Toolbar 136, 137 manuals 136 M Media Player 128 Memory capacity 79 checking capacity 79 compartment 22, 77 installing 77 problems 93 removing 79 upgrade module 77 Microphone Jack 12, 19,
S U Save-to-Disk 67 ScrLk 26 SD Card Slot 12 SDRAM 22, 77 Secure Digital Cards 75 Security Buttons 49 Security lock slot 13 Sleep Mode 65 Smart Card Slot 12 Specifications 129 Audio 130 Chipset 129 Device Ports 132 Dimensions and Weight 134 Environmental Requirements 134 Keyboard 133 mass storage device options 130 Memory 129 Microprocessor 129 Power 133 Video 130 Status Indicator Panel 15, 24 Suspend/ Resume button 13 USB 2.
Guide d’utilisation Découvrez comment utiliser votre PC Tablette LIFEBOOK Fujitsu T904 1-
Informations sur les droits d’auteurs et les marques commerciales La société Fujitsu America, Inc. a fait tous les efforts possibles pour vérifier l’exactitude des informations figurant dans ce document et s’assurer qu’il n’y manque rien. Cependant, puisque nos produits font continuellement l’objet d’améliorations, nous ne pouvons garantir l’exactitude de tout le contenu de ce document. Nous réfutons toute responsabilité relative à des erreurs, des omissions ou des modifications futures.
AVERTISSEMENT : LA MANIPULATION DU CORDON DE CE PRODUIT VOUS EXPOSE AU PLOMB, UNE SUBSTANCE CHIMIQUE QUI, SELON L’ÉTAT DE CALIFORNIE, PEUT CAUSER DES ANOMALIES CONGÉNITALES OU D’AUTRES PROBLÈMES DE REPRODUCTION. LAVEZ-VOUS LES MAINS APRÈS CHAQUE MANIPULATION. GUIDE D’UTILISATION POUR LA CONNEXION SANS FIL EN LARGE BANDE SI LE PÉRIPHÉRIQUE DE RÉSEAU ÉTENDU SANS FIL (WWAN) OPTIONNEL EST INSTALLÉ SUR VOTRE ORDINATEUR TABLETTE, LE GUIDE D’UTILISATION CORRESPONDANT EST DISPONIBLE SUR : http://solutions.us.
CONSIGNES DE SÉCURITÉ IMPORTANTES Pour fonctionner, cet appareil nécessite un adaptateur secteur. Utilisez uniquement un adaptateur pour équipement informatique, homologué UL I.T.E., avec une sortie nominale de 19 V c.c. et un courant de 4,22 A (80 W).
