Operation Manual

9 EN
Channel Presetting
Tuning of broadcast channels not already preset in the unit
can be performed in two ways.
Automatic Channel Preset
• By “AUTOMATICALLY” tuning channels and placing
them in sequential order in the unit’s memory i.e. the first
channel found will be memorised into the unit’s channel
position 1, the second channel found will be memorised
into the unit’s channel position 2 and so on.
• Execution of the “Automatic” channel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the “Manual”
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
• Each channel is tuned manually and individually. Follow
the steps laid out in the “Manual Channel Preset”.
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
2) Press
VCR, then SETUP.
3) Press
K or L to select “INITIAL”, then press B.
4) Press
K or L to select “CH TUNING”, then press B.
5) Press
K or L to select “AUTO”, then press B.
•The tuner scans and memorises all the active channels in
your area. After scanning, the tuner stops on the lowest
memorised channel.
To Select a Desired Channel
You can select a desired channel by using CHANNEL (K/L), or
directly pressing
the Number buttons on the remote control.
• Enter a channel numbers as a two-digit number for the
quickest results. For example, to select channel 6, press
0
and
6. If you only press 6, channel 6 will be selected after a
brief delay.
• You can only select channels 01–99.
Manual Channel Preset
• Use the remote control for this procedure.
1) Press
VCR, then SETUP.
2) Press
K or L to select “INITIAL”, then press B.
3) Press
K or L to select “CH TUNING”, then press B.
4) Press
K or L to select “MANUAL”, then press B.
5) Press
K or L to select “POSITION”, then press B.
•When a weak signal is received in Manual Tuning mode,
you can change the background to solid blue or the
static screen by pressing
C.RESET.
6) Press
the Number buttons, K or L to select your desired
position number, then press
B.
•You can select position number 01-99.
•If “ON” appears on the right side of “SKIP”, press
K or
L to point to “SKIP”. Then, press B to select “OFF”.
•If you want to remove scrambled signals, press
K or L
repeatedly to point to “DECODER”. Then, press
B to
select “ON”.
7) Press
K or L to select “CHANNEL”, then press B.
8) Press
K or L to start scanning.
•The unit’s tuner will begin to search up or down
automatically. When a channel is found, the unit will
stop searching and the picture will appear on the TV
Screen.
•You can select desired channel number by using
the Number buttons. You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press “
0” button first and then
press “
2” and “4”.)
•If this is the channel you want, press
B.
This unit can receive Hyper and Oscar frequency bands.
9) Press
SETUP to exit.
Note: • To confirm that a channel has been added, press
CHANNEL (K/L).
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL
(K/L).
• Use the remote control for this procedure.
1) Press
VCR, then SETUP.
2) Press
K or L to select “INITIAL”, then press B.
3) Press
K or L to select “CH TUNING”, then press B.
4) Press
K or L to select “MANUAL”, then press B.
5) Press
K or L to select “POSITION”, then press B.
6) Press
the Number buttons, K or L to select relevant
position number, then press
B.
INITIAL
CH TUNING
CLOCK
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
scanning
MENU
TIMER
SET UP
INITIAL
Channel Plan
CH Indication TV Channel
02 – 12 E2 – E12
13 – 20 A – H (only ITALY)
21 – 69 E21 – E69
74 – 78 X, Y, Z, Z+1, Z+2
80 – 99,100 S1 – S20,GAP
121 – 141 S21 – S41
INITIAL
CH TUNING
CLOCK
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[OFF]
MENU
TIMER
SET UP
INITIAL
E8G06ED(EN).fm Page 9 Friday, July 27, 2007 8:51 PM