INITIAL SETTING FLX3220F A FLX3220F CONNECTION Owner’s Manual INTRODUCTION 32” Digital / Analog LCD TV WATCHING TV OPTIONAL SETTING HIGH-DEFINITION TELEVISION TROUBLESHOOTING INFORMATION TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA. IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-827-0036, OR VISIT OUR WEB SITE AT www.elementelectronics.com A71F6UH_A71FDUH_FLX3220F A_EN.
INTRODUCTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. CAUTION: TO REDUCE THE RISK OF ELECTRIC THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. SHOCK, DO NOT REMOVE COVER (OR BACK).
INITIAL SETTING 5 Precautions CONNECTION e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance, this indicates a need for service. 20. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards. 21.
INTRODUCTION LOCATION For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
Contents INTRODUCTION Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 5 Remote Control Function CH. RECALL 1. POWER button (p13) Press to turn the unit on and off. 2. Number buttons (p16) • Press to select channels. - button • Press to shift the minor channel from the major channel. 3. SETUP button (p14) Press to display the main menu. 4. s / B / K / L buttons (p13) Press to move left/ right/ up/ down through the items. 5. ENTER button (p13) Press to decide the command of setting when the main menu is displayed. 6.
INTRODUCTION 5 Control Panel side of this unit INPUT SELECT CHANNEL SETUP 3 4 5 6 rear of this unit Y R R R AUDIO AUDIO Pb L 7 L VIDEO S VIDEO VIDEO Pr VIDEO 1 COMPONENT 2 Y R AUDIO Pb L AUDIO L 8 9 S-VIDEO 10 Pr rear of this unit INFORMATION VIDEO 2 COMPONENT 1 TROUBLESHOOTING 6 OPTIONAL SETTING 1 2 3 4 5 1. HDMI IN jack (p10) HDMI connection for an HDMI device. 2. AUDIO IN jacks (p10) RCA audio cable connection for a DVI device. (For HDMI IN jack only) 3.
INTRODUCTION 5 Attaching a Wall Mount Bracket (sold separately) The following is a description of the method for attaching a wall mount to this unit. When performing this operation, refer to the instruction manual included with the wall mount kit. # CAUTION • Any damage caused by incorrectly attempting to mount this unit is not covered under the terms of the manufacturers warranty. • This unit may be used only with CL-M manufactured by OMNIMOUNT SYSTEMS.
INTRODUCTION CONNECTION Cables not included. Please purchase the necessary cables at your local store. 5 Basic Connection CONNECTION This section describes how to connect the unit to an antenna, cable/satellite box, etc. Note: • Be sure your antenna or other device is connected properly before plugging in the power cord.
CONNECTION Cables not included. Please purchase the necessary cables at your local store. 5 External Device Connection [HDMI Connection] HDMI (High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable. It ensures that the content sent from the source to the unit is of the highest possible resolution. rear of this unit e.g.
INTRODUCTION Cables not included. Please purchase the necessary cables at your local store. CONNECTION [Component Video Cable Connection] Component video connection offers better picture quality for video devices connected to the unit. Use a component video cable to connect the unit to external video devices equipped with component video output jacks. If you connect to the unit’s COMPONENT 1 video input jack, connect RCA audio cables to the audio L/R jacks of COMPONENT 1.
CONNECTION Cables not included. Please purchase the necessary cables at your local store. [Video Connection] Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s VIDEO 1 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 1. If you connect to the unit’s VIDEO 2 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 2.
These operations are accessible by remote control. Some may also be accessible by controls on the main unit. 5 Initial Setup INTRODUCTION INITIAL SETTING Note: Before you begin: Make sure if the unit is connected to antenna or cable. [POWER] to turn on the unit. • This operation may take a few moments. INITIAL SETTING 1 After making all the necessary connections, press • If you connect the cable system directly, contact the CATV installer.
INITIAL SETTING 5 Main Menu 5 Auto Channel Scan This section describes the overview of the main menu displayed when you press [SETUP]. For more details, see the reference page for each item. The main menu consists of the function setting items below. If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channel you deleted, you will need to perform auto channel scan.
5 Language Selection You can choose English, Spanish, or French as your on-screen language. 1 Press [SETUP] to display the main menu. CONNECTION 2 Use [Cursor K/L] to select “LANGUAGE”, then press INITIAL SETTING • If you connect the cable system directly, contact the CATV installer. • If you press [POWER] or [SETUP] during auto channel scan, the setting will be canceled. • Channel settings will be saved even if the power fails.
WATCHING TV 5 Channel Selection 5 Volume Adjustment Select channels by pressing [CH K / L] or [the Number buttons]. This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described. • To select the memorized channels, use [CH K / L] or [the Number buttons]. • To select the non-memorized channels, use [the Number buttons]. Use [VOL. X / Y] to adjust the audio volume.
5 Switching Each Mode You can freeze the image shown on the TV screen. You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access an external device when they are connected to the unit. CONNECTION Press [STILL] to pause the image shown on the screen. Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes. Still TV/DTV channel Video1 INITIAL SETTING • The sound output will not be paused.
WATCHING TV 5 Switching Audio Mode This section describes how to switch the audio language. DTV TV 1 Press [AUDIO] to display the currently selected audio mode. While receiving an MTS broadcast, press repeatedly to cycle through the available audio channel. 1 Press [AUDIO] to display the currently selected language and the number of available languages. 6-1 English 1/3 6 SAP / STEREO 2 Press [AUDIO] repeatedly to cycle through the available audio languages.
INTRODUCTION 5 Screen Information You can display the currently selected channel or other information such as the audio mode on the TV screen. DTV TV In the digital mode, the detailed broadcasting information for the current channel such as program title, program guides are displayed. CONNECTION In the analog mode, the current channel number and the audio mode are displayed. Press [INFO] to display the details of the currently selected program. Press [INFO].
WATCHING TV 5 TV Screen Display Mode 4 types of display modes can be selected when the broadcasting station is sending 4:3 or 16:9 video signal. Press [SCREEN MODE aspect ratio. ] repeatedly to switch the TV For 16:9 video signal For 4:3 video signal Sidebar (normal) Wide Full (normal) Zoom Expand Cinema Full Cinema [Sidebar] Display a 4:3 picture at its original size. Sidebars appear on both edges of the screen.
5 Manual Register The channel list function lets you remove undesired channels from the channel registration list. The manual register function lets you add the channels that were not added by the auto channel scan due to the reception condition at the initial setting. 1 Press [SETUP] to display the main menu. 1 Press [SETUP] to display the main menu.
OPTIONAL SETTING 5 Antenna Confirmation This function lets you check the signal strength of each channel. 1 Press [SETUP] to display the main menu. 2 Use [Cursor K/L] to select “CHANNEL”, then press [ENTER]. 3 Use [Cursor K/ L] to select “Antenna”, then press [ENTER]. Channel Autoscan Channel List Manual Register Antenna 4 Use [the Number buttons] or [CH K/L] to select the channel for which you want to check the signal strength.
Cursor s You can adjust brightness, contrast, color, tint and sharpness. INTRODUCTION 5 Picture Adjustment Cursor B Brightness Brightness Move ENTER Enter Move ENTER Enter Move ENTER Enter Move ENTER Enter Move ENTER Enter to decrease brightness to increase brightness to decrease contrast to increase contrast to decrease color to brighten color to add red to add green to make soft to make clear CONNECTION 1 Press [SETUP] to display the main menu.
OPTIONAL SETTING 5 Closed Caption You can view closed captioning (cc) for TV programs, movies and news. Closed caption refer to text of dialogue or descriptions displayed on-screen for the hearing impaired. 1 Press [SETUP] to display the main menu. 2 Use [Cursor K/L] to select “DETAIL”, then press [ENTER]. 3 Use [Cursor K/L] to select “Closed Caption”, then [Caption Mode] CC1 and Text1; are the primary caption and text services.
INTRODUCTION 5 DTV Closed Caption DTV 1 Press [SETUP] to display the main menu. CONNECTION In addition to the basic closed caption described on page 24, DTV has its own closed caption called DTV CC. Use this menu to change the settings for DTV CC. 5 Use [Cursor K/L] to select the desired DTV closed caption, then press [ENTER]. INITIAL SETTING Closed Caption Conventional CC DTV CC Off CC Style Service1 Service2 2 Use [Cursor K/L] to select “DETAIL”, then press Service3 Service4 [ENTER].
OPTIONAL SETTING 5 CC Style You can change the style of CC such as font, color or size, etc. 6 Use [Cursor K/L] to select “On”, then press [ENTER]. 1 Press [SETUP] to display the main menu. CC Style Closed Caption User Setting On Font Style Off Font Size Font Color Font Opacity Back Color 2 Use [Cursor K/L] to select “DETAIL”, then press Back Opacity Edge Color [ENTER]. Edge Type 7 Use [Cursor K/L] to select an item, then press [ENTER].
INTRODUCTION CC Style [Edge Type] Edge type of the displayed caption can be switched as below. CC Style Closed Caption Closed Caption User Setting User Setting Font Style White Font Style Black Font Size Red Font Color None Font Opacity Green Font Opacity Raised Back Color Blue Back Color Depressed Back Opacity Yellow Back Opacity Uniform Edge Color Magenta Edge Color L.Shadow Edge Type Cyan Edge Type R.
OPTIONAL SETTING 5 V-chip V-chip reads the ratings for programs, then denies access to the programs which exceed the rating level you set. With this function, you can block certain programming inappropriate for children. See the following description for setting each item. 1 Press [SETUP] to display the main menu. V-chip MPAA Rating A TV Rating B Downloadable Rating Clear Downloadable Rating New Password 2 C Use [Cursor K / L] to select “DETAIL”, then press [ENTER]. A... “A.
INTRODUCTION A. MPAA Rating B. TV Rating MPAA Rating is the rating system created by MPAA (Motion Picture Association of America). [ENTER]. 5 Use [Cursor K/L] to select “TV Rating”, then press [ENTER]. V-chip V-chip MPAA Rating TV Rating TV Rating Downloadable Rating Downloadable Rating Clear Downloadable Rating Clear Downloadable Rating New Password New Password 6 Use [Cursor K/L/s/B] to select the desired rating, then press [ENTER] repeatedly to switch between “View” and “Block”.
OPTIONAL SETTING C. New Password Although the default code “0000” is supplied with the unit, you can set your own password. Rating 5 Use [Cursor K/L] to select “New Password”, then press Category TV-MA Mature audience only TV-14 Unsuitable for children under 14 TV-PG Parental guidance suggested TV-G General audience TV-Y7 Appropriate for all children 7 and older TV-Y Appropriate for all children Sub Rating Category higher [ENTER].
INTRODUCTION 5 HDMI Audio You can set the method of sound input for the HDMI - IN jack. 1 Press [SETUP] to display the main menu. CONNECTION 2 Use [Cursor K/L] to select “DETAIL”, then press INITIAL SETTING [ENTER]. WATCHING TV 3 Use [Cursor K/L] to select “HDMI Audio”, then press [ENTER]. Detail OPTIONAL SETTING Closed Caption V–chip HDMI Audio Auto TROUBLESHOOTING 4 Use [Cursor K/L] to select the desired sound input, then press [ENTER].
TROUBLESHOOTING 5 Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service. Symptom Remedy No power • Be sure the power cord is plugged in. • If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to reset itself. No picture or sound • Check if the power is on. • Check the outlet connection. • Check the antenna or cable connection to the main unit.
INTRODUCTION Remote control does not work • Check the antenna or cable connection to the main unit. • Check the batteries of the remote control. • Check if there is an obstacle between the infrared sensor window and the remote control. • Test the signal output. If OK, then possible infrared sensor trouble. (Refer to “IR Signal Check” on page 34.) • Aim the remote control directly at the infrared sensor window on the front of the unit. • Reduce the distance to the unit.
INFORMATION 5 Glossary ATSC Dolby Digital Password Acronym that stands for Advanced Television Systems Committee and the name of the digital broadcasting standards. The system developed by Dolby Laboratories to compress digital sound. It offers stereo sound (2ch) or multi-channel audio. A stored 4-digit number that allows access to parental control features. Aspect Ratio HDMI (high-definition multimedia interface) The width of a TV screen relative to its height.
INTRODUCTION 5 Cable Channel Designations If you subscribe to cable TV, the channels are displayed as 1-135. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations.
LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: LABOR: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts and LCD image burn-in are excluded from this warranty. FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
AJUSTE INICIAL FLX3220F A FLX3220F CONEXIÓN Manual del usuario INTRODUCCIÓN Televisión Digital / Analógica con pantalla LCD de 32 pulgadas PARA VER LA TELEVISIÓN AJUSTE OPCIONAL HIGH-DEFINITION TELEVISION SOLUCIÓN DE PROBLEMAS INFORMACIÓN PARA RECIBIR LA SEÑAL DIGITAL/ ANALÓGICA, DEBE CONECTAR LA ANTENA. SI NECESITA AYUDA ADICIONAL CON LA INSTALACIÓN O CON EL FUNCIONAMIENTO DESPUÉS DE LEER EL MANUAL DEL USUARIO, LLAME AL TELÉFONO GRATUITO 1-800-827-0036, O VISITE NUESTRO SITIO WEB EN: www.
INTRODUCCIÓN ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LLUVIA O HUMEDAD. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CUIDADO: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PLACA TRASERA). EL INTERIOR DE ESTE APARATO NO CONTIENE PIEZAS REPARABLES POR EL USUARIO. DEJE LA REPARACIÓN EN MANOS DE PERSONAL DE SERVICIO TÉCNICO CUALIFICADO.
AJUSTE INICIAL PARA VER LA TELEVISIÓN 5 Precauciones LA LÁMPARA DE LA PANTALLA LCD CONTIENE MERCURIO. SE DEBE TIRARLA DE ACUERDO A LA NORMATIVA LOCAL O LA LEY FEDERAL. PARA EVITAR LA DESCARGA ELÉCTRICA, HAGA COINCIDIR EL CONTACTO ANCHO DEL ENCHUFE CON LA RANURA ANCHA E INSERTE FIRMEMENTE. ADVERTENCIA DE LA FCC Este equipo puede generar o utilizar energía de radiofrecuencia.
INTRODUCCIÓN UBICACIÓN Para un funcionamiento seguro y un rendimiento satisfactorio de la unidad, tenga en cuenta lo siguiente a la hora de seleccionar un lugar para su instalación: • Debe protegerlo de la luz solar directa y mantenerlo alejado de fuentes de calor intenso. • Evite lugares polvorientos o húmedos. • Evite lugares con ventilación insuficiente para una disipación de calor adecuada. No bloquee los orificios de ventilación situados en la parte superior e inferior de la unidad.
5 Contenido INTRODUCCIÓN CONEXIÓN Conexión Básica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Conexión de Dispositivo Externo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AJUSTE INICIAL PARA VER LA TELEVISIÓN AJUSTE OPCIONAL SOLUCIÓN DE PROBLEMAS SOLUCIÓN DE PROBLEMAS Lista de Canales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Registro Manual . . . . . . .
INTRODUCCIÓN 5 Función del Mando a Distancia CH. RECALL 1. Botón POWER (p. 13) Presione para activar y desactivar la unidad. 2. Botones numéricos (p. 16) • Presione para seleccionar los canales. Botón – • Presione para separar el canal menor del canal mayor. 3. Botón SETUP (p. 14) Presione para visualizar el menú principal. 4. Botones s / B / K / L (p. 13) Presione para desplazarse por los elementos, izquierda/ derecha/ arriba/ abajo. 5. Botón ENTER (p.
INTRODUCCIÓN 5 Panel de Control parte lado de la unidad INPUT SELECT CHANNEL SETUP 3 4 5 6 parte trasera de la unidad Y R R R AUDIO AUDIO Pb L 7 L VIDEO S VIDEO VIDEO Pr VIDEO 1 COMPONENT 2 Y R AUDIO Pb L AUDIO L 8 9 S-VIDEO 10 Pr parte trasera de la unidad parte lado de la unidad INFORMACIÓN VIDEO 2 COMPONENT 1 SOLUCIÓN DE PROBLEMAS 6 AJUSTE OPCIONAL 1 2 3 4 5 1. Toma HDMI IN (p.10) Conexión HDMI para un dispositivo HDMI. 2. Tomas AUDIO IN (p.
INTRODUCCIÓN 5 Instalación de un Soporte para el Montaje en Pared (se vende por separado) A continuación se ofrece una descripción del método para instalar un soporte para el montaje en pared en esta unidad. Al realizar esta operación, consulte el manual de instrucciones incluido con el juego de montaje en pared. # CUIDADO • Cualquier daño causado por un intento incorrecto de instalar esta unidad no está protegida por la garantía del fabricante.
INTRODUCCIÓN CONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. 5 Conexión Básica CONEXIÓN En esta sección se describe cómo conectar la unidad a una antena, caja de cable/satélite, etc. Nota: • Asegúrese de que su antena u otra dispositivo está conectada correctamente antes de enchufar el cable de alimentación.
CONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. 5 Conexión de Dispositivo Externo [Conexión HDMI] HDMI (High Definition Multimedia Interface/Interfaz multimedia de alta definición) es una interfaz que transmite vídeo y audio digital por canales múltiples de alta definición mediante un solo cable. Esto asegura que las señales que se envían desde la fuente hacia la unidad son de la más alta definición posible.
INTRODUCCIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. CONEXIÓN [Conexión de Cable de Vídeo en Componentes] La conexión de vídeo en componentes ofrece una mejor calidad de imagen para dispositivos de vídeo conectados a la unidad. Utilice un cable de vídeo en componentes para conectar la unidad a dispositivos de vídeo externos equipados con tomas de salida de vídeo en componentes.
CONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. [Conexión de Vídeo] La conexión de vídeo ofrece una calidad normal de imagen para dispositivos de vídeo conectados a la unidad. Si se conecta a la toma de entrada de vídeo VIDEO1 de la unidad, conecte los cables de audio RCA a las tomas de audio L/R (izquierda/derecha) de VIDEO1.
INTRODUCCIÓN AJUSTE INICIAL Se puede acceder a estas operaciones mediante el mando a distancia. Algunas también pueden ser accesibles mediante los mandos de la unidad principal. 5 Configuración Inicial Nota: Antes de empezar: Asegúrese de que la unidad está conectada a la antena o al cable. PARA VER LA TELEVISIÓN • Esta operación tardará unos momentos. 2-2 Utilice [Cursor K / L] para seleccionar el idioma de 2 pantalla entre las opciones de la derecha de la pantalla No channel is registered.
AJUSTE INICIAL 5 Menú Principal En esta sección se describen los aspectos generales del menú principal que aparece al presionar [SETUP]. Para más detalles, consulte la página de referencia de cada elemento. El menú principal se compone de los siguientes elementos de ajuste de función.
5 Selección de Idioma Puede elegir Inglés, Español, Francés como idioma de pantalla. 1 Presione [SETUP] para visualizar el menú principal. CONEXIÓN [Cursor K / L] para seleccionar “IDIOMA”, y 2 Utilice luego presione [ENTER]. AJUSTE INICIAL • Si se conecta directamente al sistema de cable, póngase en contacto con el instalador de CATV. • Si presiona [POWER] o [SETUP] durante la exploración automática de canales, este ajuste se cancelará.
PARA VER LA TELEVISIÓN 5 Selección de Canal 5 Ajuste de Volumen Seleccione los canales presionando [CH K / L] o [los botones numéricos]. En esta sección se describe cómo ajustar el volumen. También se describe la función de silenciamiento, que activa y desactiva el sonido. • Para seleccionar los canales memorizados, utilice [CH K / L] o [los botones numéricos]. • Para seleccionar los canales no memorizados, utilice [los botones numéricos]. Utilice [VOL. X / Y] para ajustar el volumen de audio.
5 Para Cambiar entre Cada Modo Puede congelar la imagen mostrada en la pantalla del televisor. Puede cambiar fácilmente entre DTV (ATSC) y TV (NTSC) o acceder a un dispositivo externo con el mando a distancia cuando estén conectados a la unidad. Presione [INPUT SELECT] o [CH K] varias veces para pasar a través de todos los modos de entrada. CONEXIÓN Presione [STILL] para detener momentáneamente la imagen mostrada en pantalla.
PARA VER LA TELEVISIÓN 5 Para Cambiar el Modo de Audio En esta sección se describe cómo cambiar el idioma de audio. DTV TV [AUDIO] para mostrar por pantalla el modo de [AUDIO] para visualizar el idioma actualmente 1 Presione 1 Presione audio actualmente seleccionado. Durante la recepción seleccionado y el número de idiomas disponibles. de una emisión MTS, presione repetidamente para recorrer los canales de audio disponibles.
INTRODUCCIÓN 5 Información de Pantalla Puede visualizar el canal actualmente seleccionado u otra información, por ejemplo el modo de audio, en la pantalla del televisor. DTV TV CONEXIÓN En el modo analógico se visualizan el número del canal actual y el modo de audio. En el modo digital se visualiza la información de emisión detallada para el canal actual como, por ejemplo, el título del programa y las guías de programas.
PARA VER LA TELEVISIÓN 5 Modo de Visualización de Pantalla del Televisor Pueden seleccionarse 4 tipos de modos de visualización cuando la emisora envía una señal de vídeo de 4:3 o 16:9. Presione [SCREEN MODE ] repetidamente para cambiar la relación del aspecto del televisor. Para señal de vídeo 16:9 Para señal de vídeo 4:3 Sidebar (normal) Ancha Total (normal) Zoom Amplía Cine Total Cine [Sidebar] Visualización de una imagen 4:3 en su tamaño original.
5 Registro Manual La función Lista de canales le permite eliminar los canales no deseados de la lista de inscripción de canales. La función de registro manual permite agregar los canales que no se agregaron mediante la exploración automática de canales debido al estado de la recepción en el ajuste inicial. 1 Presione [SETUP] para visualizar el menú principal. 1 Presione [SETUP] para visualizar el menú principal.
AJUSTE OPCIONAL 5 Confirmación de la Antena Esta función le permite comprobar la intensidad de la señal de cada canal. 1 Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “CANAL”, y luego 2 presione [ENTER]. Utilice [Cursor K / L] para seleccionar “Antena”, y luego 3 presione [ENTER].
Puede ajustar el brillo, el contraste, el color, el matiz y la nitidez. Claridad Claridad 1 Presione [SETUP] para visualizar el menú principal. 30 Ajuste Mover ENTER Entre Mover ENTER Entre Mover ENTER Entre Mover ENTER Entre Contraste Contraste 60 Ajuste Utilice [Cursor K / L] para seleccionar “IMAGEN”, y 2 luego presione [ENTER].
AJUSTE OPCIONAL 5 Subtítulos Puede ver los subtítulos (cc) para programas de televisión, películas e informativos. Subtítulo se refiere al texto de diálogo o descripciones visualizadas en pantalla para personas con problemas auditivos. 1 Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “DETALLE”, y 2 luego presione [ENTER]. Utilice [Cursor K / L] para seleccionar 3 “Subtítulo Cerrado”, y luego presione [ENTER]. [Modo de subtítulos] S.C.
INTRODUCCIÓN 5 Subtítulos en DTV DTV 1 Presione [SETUP] para visualizar el menú principal. CONEXIÓN Además de los subtítulos básicos descritos en la página 24, DTV tiene sus propios subtítulos denominados DTV CC. Utilice este menú para cambiar la configuración de DTV CC. [Cursor K / L] para seleccionar los subtítulos 5 Utilice DTV deseados, y luego presione [ENTER]. Subtítulo Cerrado S.C. DTV Off Estilo S.C. Servicio1 AJUSTE INICIAL S.C.
AJUSTE OPCIONAL 5 Estilo CC Puede cambiar el estilo de CC, por ejemplo fuente, color o tamaño, etc. 1 Presione [SETUP] para visualizar el menú principal. [Cursor K / L] para seleccionar “On”, y luego 6 Utilice presione [ENTER]. Estilo S.C. Subtítulo Cerrado Config. Usuarid On Estilo Fuente Off Tamaño Fuente Color Fuente Utilice [Cursor K / L] para seleccionar “DETALLE”, y 2 luego presione [ENTER].
INTRODUCCIÓN Estilo S.C. [Tipo Borde] El tipo de borde del subtítulo mostrado puede cambiarse como sigue. Estilo S.C. Subtítulo Cerrado Config. Usuarid Subtítulo Cerrado Config. Usuarid Blanco Estilo Fuente Negro Tamaño Fuente Color Fuente Rojo Color Fuente Ninguno Opaco Fuente Verde Opaco Fuente Elevado Color Fondo Azul Color Fondo Hundido Opaco Atrás Amarillo Opaco Atrás Uniforme Color Borde Magenta Color Borde Sombra Izq. Tipo Borde Cyan Tipo Borde Sombra Der.
AJUSTE OPCIONAL 5 V-chip V-chip lee las clases de los programas, y niega el acceso a los programas que exceden el nivel de clasificación establecido. Con esta función, puede bloquear determinados programas inapropiados para niños. 1 Presione [SETUP] para visualizar el menú principal. Consulte la siguiente descripción para ajustar cada elemento. V-chip Clase de MPAA A Clase de TV B Clase descargada Utilice [Cursor K / L] para seleccionar “DETALLE”, y 2 luego presione [ENTER].
INTRODUCCIÓN B. Clase de TV A. Clase de MPAA Clase de MPAA es el sistema de clasificación creado por la MPAA (Motion Picture Association of America). CONEXIÓN [Cursor K / L] para seleccionar “Clase de MPAA”, [Cursor K / L] para seleccionar “Clase de TV”, y 5 yUtilice 5 Utilice luego presione [ENTER]. luego presione [ENTER].
AJUSTE OPCIONAL C. Nueva Código de Acceso Aunque el código predeterminado “0000” viene incorporado con la unidad, usted puede ajustar su propia contraseña.
INTRODUCCIÓN 5 Audio HDMI Puede ajustar el mecanismo de entrada de sonidopara la toma HDMI IN. CONEXIÓN 1 Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “DETALLE”, y 2 luego presione [ENTER]. AJUSTE INICIAL PARA VER LA TELEVISIÓN Utilice [Cursor K / L] para seleccionar “Audio HDMI”, y 3 luego presione [ENTER].
SOLUCIÓN DE PROBLEMAS 5 Guía de Solución de Problemas Si la unidad no funciona correctamente cuando se siguen las instrucciones de este manual del usuario, compruebe la siguiente tabla antes de llamar al servicio técnico. Síntoma Solución No hay corriente • Asegúrese de que el cable de alimentación está enchufado. • Si se produce un corte de alimentación, desenchufe el cable de alimentación durante 30 minutos para permitir que la unidad se reinicie.
INTRODUCCIÓN El mando a distancia no funciona • Compruebe la conexión de antena o de cable con la unidad principal. • Compruebe las pilas del mando a distancia. • Compruebe si hay algún obstáculo entre la ventana del sensor de infrarrojos y el mando a distancia. • Pruebe la salida de la señal. Si es correcta, es posible que haya algún problema con el sensor de infrarrojos. (Consulte “Comprobación de la Señal de Infrarrojos (IR)” en la página 34.
INFORMACIÓN 5 Glosario ATSC HDTV (televisión de alta definición) Acrónimo de “Advanced Television Systems Committee” (Comité de sistemas avanzados de televisión) y el nombre de unas normas de emisión digital. Reciente formato digital que produce una alta resolución y una elevada calidad de imagen. SDTV (televisión de definición estándar) Formato digital estándar similar a la calidad de imagen de NTSC.
INTRODUCCIÓN 5 Denominaciones de Canales de Cable Si se suscribe a la televisión por cable, los canales se muestran como 1-135. Las empresas de cable a menudo denominan los canales con letras o combinaciones de letra-número. Compruebe este detalle con su empresa local de cable. La tabla siguiente incluye las denominaciones de canal de cable habituales.
GARANTÍA LIMITADA FUNAI CORP. reparará este producto, de forma gratuita en Estados Unidos, en caso de defecto de materiales o fabricación, del modo siguiente: DURACIÓN: PIEZAS: FUNAI CORP. suministrará piezas de repuesto de las piezas defectuosas de forma gratuita durante un (1) año desde la fecha de compra minorista original. Determinadas piezas y el efecto de persistencia de la imagen en la pantalla LCD están excluidas de esta garantía. MANO DE OBRA: FUNAI CORP.