E1T12ED_EN.book Page 1 Tuesday, August 3, 2010 5:13 PM INTRODUCTION FUNCTION SETUP OWNER’S MANUAL PLAYBACK HT2-M200 CONNECTIONS Home Theater System OTHERS For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
E1T12ED_EN.book Page 2 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Safety Instructions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
E1T12ED_EN.book Page 3 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Avoid the Hazards of Electrical Shock and Fire Moisture Condensation Warning Following information is only valid EU-member States: Make your contribution to the environment!!! • Exhausted batteries do not belong in the dustbin. • You can dispose of them at a collection point for exhausted batteries or special waste. • Contact your council for details.
E1T12ED_EN.book Page 4 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Maintenance Cleaning the Unit Use a soft cloth slightly moistened with a mild detergent solution. Do not use solutions containing alcohol, spirits, ammonia or abrasives. Cleaning Discs If a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion.
E1T12ED_EN.book Page 5 Tuesday, August 3, 2010 5:13 PM INTRODUCTION INTRODUCTION Supplied Accessories • • • • • Remote Control Batteries (R6,1.5V × 2) Video cable FM wire antenna 1 centre, 2 front, 2 rear speakers and 1 subwoofer • • • • Owner’s Manual Quick Start Guide CD-ROM Warranty card INTRODUCTION PLAYBACK Information on Playback.......................................................... 16 How to Insert a Disc...................................................................
E1T12ED_EN.book Page 6 Tuesday, August 3, 2010 5:13 PM INTRODUCTION DivX®, DivX Certified® and associated logos are registered trademarks of DivX, Inc. and are used under license. Trademark Information HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
E1T12ED_EN.book Page 7 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Blu-ray Disc You can enjoy Blu-ray Disc which is capable of storing five times more data than a conventional DVD. Enjoy your content on different kinds of media Full backwards compatibility with BD, DVD, CD and SD card ensures that you can continue to enjoy your current audio-video collection. Additionally, you can enjoy AVCHD / DivX® / MP3 / WMA / JPEG files.
E1T12ED_EN.book Page 8 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Front Panel 1 2 3 4* STANDBY/ON 5 6 7 8 9* 10 VOLUME OPEN/CLOSE PLAY STOP SD CARD SOURCE MP3 LINE-IN 12 11 (*) The unit can also be turned on by pressing these buttons. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. STANDBY/ON Q button STANDBY/ON indicator Disc tray OPEN/CLOSE A button* Infrared sensor window Display VOLUME K / L buttons STOP C button PLAY B button* SOURCE button 11. MP3 LINE-IN jack 12.
E1T12ED_EN.book Page 9 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Install 2 R6 (1.5V) batteries matching the polarity indicated inside battery compartment of the remote control. 1) 2) In stop mode and “Mode Select” is set to “Network”, opening screen is displayed. 3) 2 1 CONNECTIONS 1 INTRODUCTION Opening Screen Installing the Batteries in the Remote Control 2 Make sure to match + and - on the batteries to the marks indicated in the battery compartment.
E1T12ED_EN.book Page 10 Tuesday, August 3, 2010 5:13 PM INTRODUCTION Front Panel Display 1 2 3 4 * Brightness of the display can be adjusted. Refer to “Panel Display” in “List of Setup Menus” on page 40. 1. 2. 3. 4. Displays repeat icon. (Appears during repeat playback.) Displays media icon (disc mode or SD card mode). Displays playback status icon. Refer to the table A below.
E1T12ED_EN.book Page 11 Tuesday, August 3, 2010 5:13 PM INTRODUCTION CONNECTIONS Placing the Speakers Make the following connection to ensure an optimum sound experience. CENT ER CONNECTIONS FRON T LEFT REAR LEFT FRON T RIGHT WO PLAYBACK SUB REAR RIGHT OFE R Note Connection to the TV Choose the appropriate connection, then proceed to the corresponding instruction on the pages 11-12. Best (Supports up to 1080i, 1080p, 1080p/24 resolution.
E1T12ED_EN.book Page 12 Tuesday, August 3, 2010 5:13 PM CONNECTIONS Better (Supports up to 1080i resolution.) Your TV COMPONENT VIDEO IN Y PB/CB PR/CR Component video cable No supplied cables are used in this connection: Please purchase the necessary cables at your local store. Basic (Supports only 480i/576i resolution.) Your TV Video cable VIDEO IN • Connect this unit directly to the TV.
E1T12ED_EN.book Page 13 Tuesday, August 3, 2010 5:13 PM CONNECTIONS INTRODUCTION Connecting Speakers and Subwoofer CONNECTIONS Front centre Rear right Rear left Front right PLAYBACK Subwoofer Front left Make sure that the colours of the cables and sockets are matched. Note • To prevent unwanted noise, never place the speakers too close to the main unit, subwoofer, AC power adapter, TV or any other radiation sources. This unit provides analogue and digital audio connection.
E1T12ED_EN.book Page 14 Tuesday, August 3, 2010 5:13 PM CONNECTIONS Connecting Portable Media Player STANDBY/ON VOLUME OPEN/CLOSE SD CARD STOP Network Connection with LAN PLAY SOURCE MP3 LINE-IN By connecting this unit to the Internet, you can update the software via the Internet or access the BD-Live and vTuner service. MP3 LINE-IN Networking equipment (modem, etc.) Hub or broadband router MP3 WAN LAN Connect a 3.
E1T12ED_EN.book Page 15 Tuesday, August 3, 2010 5:13 PM CONNECTIONS INTRODUCTION After you have completed all the connections, you must find the correct video channel (external input channel) on your TV. Finding the Video Channel on Your TV After you have completed all the connections, you must find the correct video channel (external input channel) on your TV. 1 After you have made all the necessary CONNECTIONS 2 3 connections, press [STANDBY/ON Q] to turn on the unit. Turn on your TV.
E1T12ED_EN.book Page 16 Tuesday, August 3, 2010 5:13 PM PLAYBACK Information on Playback Before you start playing back a disc, read the following information. Playable Discs and Files Readable cards This unit is compatible to play back the following discs / files. To play back a disc / file, make sure that it meets the requirements for region codes and colour systems as described below. You can play back discs that have the following logos. Other disc types are not guaranteed to play back.
E1T12ED_EN.book Page 17 Tuesday, August 3, 2010 5:13 PM PLAYBACK microSD Card adapter microSD Card BD-video DVD-video 2 FUNCTION SETUP • Portions of this product are protected under copyright law and are provided under licence by ARIS / SOLANA / 4C. • Please keep the SD Memory Cards in their cases when you are not using them. • Do not try to open or modify the card. • Do not touch the terminal surface with your fingers or any metals. • Do not attach additional labels or stickers to cards.
E1T12ED_EN.book Page 18 Tuesday, August 3, 2010 5:13 PM PLAYBACK On-Screen Display You can check information about the current disc by pressing [DISPLAY]. To call the on-screen display menu, press [DISPLAY] during playback. Every time you press [DISPLAY], the information changes. Depending on the media, available information varies.
E1T12ED_EN.book Page 19 Tuesday, August 3, 2010 5:13 PM PLAYBACK INTRODUCTION File name information How to Insert a Disc 1 Press [OPEN/CLOSE A] to open the disc tray. 2 Place the disc on the disc tray with its label File_name_001 1 side facing up. 1. Media icon and file name : MP3 files : WMA files : JPEG files CONNECTIONS : DivX® files Align the disc to the disc tray guide. Tag information TITLE • Make sure the disc is compatible with this unit.
E1T12ED_EN.book Page 20 Tuesday, August 3, 2010 5:13 PM PLAYBACK Playing Back a BD, DVD or a Disc with AVCHD Files 1 Insert a disc (refer to “How to Insert a Disc” on page 19 ). Playback may start automatically. 2 If not, press [B (play)]. Some discs may show a title or a disc menu. In such case, refer to “Using the Title / Disc / Pop-up Menu” on page 20. To pause playback: Press [F (pause)]. To return to the normal playback: Press [B (play)]. To stop playback: Press [C (stop)].
E1T12ED_EN.book Page 21 Tuesday, August 3, 2010 5:13 PM PLAYBACK 1 Insert an audio CD or a disc with DivX®, MP3, WMA or JPEG files. • Media filter screen will appear. • For audio CD and a disc contains only one type of file, skip to step 3. 3 • If you press [ENTER] on the desired file, playback will start. 1 2 3 4 5 6 - - / 20 7 Folder_1 Folder_2 Folder_3 JPEG_A JPEG_B JPEG_C JPEG_D Page Up Page Down Media Mode e.g.
E1T12ED_EN.book Page 22 Tuesday, August 3, 2010 5:13 PM PLAYBACK KODAK Picture CD Reading the SD Memory Card This unit can also run JPEG files stored on KODAK Picture CD. You can enjoy picture images on the TV set by playing back the KODAK Picture CD. This unit conforms to ver.7.0 of KODAK Picture CD. For details of KODAK Picture CD, contact a shop that provides developing service of Kodak Inc.
E1T12ED_EN.book Page 23 Tuesday, August 3, 2010 5:13 PM PLAYBACK • Do not remove the SD Memory Card or turn the unit to the standby mode while the contents of the card are in playback. It may result in malfunction or loss of the card’s data.
E1T12ED_EN.book Page 24 Tuesday, August 3, 2010 5:13 PM PLAYBACK Playing Back DivX® with DivX® External Subtitle Subtitles created by the user can be displayed during DivX® playback. 1 Follow steps 1 to 3 in “Playing Back an Audio 2 CD or a Disc with DivX® / MP3 / Windows Media™ Audio / JPEG Files” on page 21. Select a file you want to play back, then press [YELLOW]. Fast Forward / Fast Reverse 1 During playback, press [D (forward)] repeatedly for fast forward.
E1T12ED_EN.book Page 25 Tuesday, August 3, 2010 5:13 PM PLAYBACK Programme Playback 1 In pause mode, press [F (pause)] repeatedly. Every time you press [F (pause)], playback will advance one step at a time. Press [B (play)] to return to normal playback. • Only step by step forward is available. • Set “Still Mode” setting to “Field” in “Video” menu if pictures in step by step playback mode are blurred. Refer to “Still Mode” on page 38. press [ENTER].
E1T12ED_EN.book Page 26 Tuesday, August 3, 2010 5:13 PM PLAYBACK 3 Press [B (play)] to start programme playback. • The programme playback will start. To exit from the programme playback mode: • Press [RETURN] in stop mode. Random Playback This function shuffles the playback order of tracks / files.
E1T12ED_EN.book Page 27 Tuesday, August 3, 2010 5:13 PM PLAYBACK Reduces the noise of the playback picture. 1 During playback, press [MODE] repeatedly 3 Press [RETURN] to exit. • The secondary audio will not be output when the secondary audio is set to “Off” or when “BD Audio Mode” is set to “HD Audio Output”. Refer to “Switching Audio Soundtrack” on page 29 and “Setting the BD Audio Mode” on page 30.
E1T12ED_EN.book Page 28 Tuesday, August 3, 2010 5:13 PM PLAYBACK Note Using [SEARCH] • You must connect the unit to the Internet and set up necessary settings in order to use BD-Live. • For certain discs, “BD-Live Setting” may need to be changed. • Depending on your connection environment, it may take time to connect to the Internet or the Internet may not be connected. • When BD-Live functions are used and the unit is connected to the Internet, you may be charged for this communication.
E1T12ED_EN.book Page 29 Tuesday, August 3, 2010 5:13 PM PLAYBACK Switching Subtitles Some video materials may have subtitles in 1 or more languages. For commercially available discs, the supported languages can be found on the disc case. Follow the steps below to switch the subtitle language during playback. “Secondary Subtitle” or “Subtitle Style”, then press [ENTER]. “Secondary Subtitle” “Subtitle Style” : Sets the subtitle for the primary video. : Sets the subtitle for the secondary video.
E1T12ED_EN.book Page 30 Tuesday, August 3, 2010 5:13 PM PLAYBACK Note Note • The secondary audio will not be output when the secondary video is not displayed or when “BD Audio Mode” is set to “HD Audio Output”. (For some BD, secondary audio will be output even when secondary video is off.) • The sound mode cannot be changed during playback of discs not recorded in multiple audio. • Some discs allow changing the audio language setting on the disc menu. (Operation varies depending on the discs.
E1T12ED_EN.book Page 31 Tuesday, August 3, 2010 5:13 PM PLAYBACK Selecting Sound Effect Mode Select the surround mode for the audio output from 5.1ch speakers. Select the sound effect mode for the audio output from 5.1ch speakers to suit your video or music. 1 During playback, press [SURROUND] 1 During playback, press [SOUND MODE] “Off”: Turns off virtual surround modes and enables 2ch PCM or multi-channel Dolby or DTS sound modes depending on source audio.
E1T12ED_EN.book Page 32 Tuesday, August 3, 2010 5:13 PM PLAYBACK Switching Active Source Mode You can change the active source mode to the desired external audio inputs and enjoy audio from the connected device with the multi-channel surround sound capabilities. 1 Press [SOURCE + / –] . • “Input Select” screen will appear. 2 Use [K / L] to select the desired source mode, To cancel sleep timer : Press [SLEEP] repeatedly until “SLP OFF” is displayed.
E1T12ED_EN.book Page 33 Tuesday, August 3, 2010 5:13 PM PLAYBACK INTRODUCTION Deleting a Preset Radio Station Note • While auto tuning, audio will be muted until this unit finds a radio station with sufficient signal strength. 1 Follow steps 1 to 2 in “Presetting Radio Stations” on page 32. 2 Use [RED] / [GREEN] / [YELLOW] / [BLUE] to select the desired preset station.
E1T12ED_EN.book Page 34 Tuesday, August 3, 2010 5:13 PM PLAYBACK “Recently Played” “Favorites” “My Added Stations” “Location” “Genre” “New Stations” “Most Popular Stations” “Get access code” “Reset” : List of stations which are recently played : List of your favourite radio stations : List of stations which are added on vTuner website (This category will appear only after you add stations on vTuner website.
E1T12ED_EN.book Page 35 Tuesday, August 3, 2010 5:13 PM PLAYBACK 1 Follow step 1 in “Internet Radio Playback” on page 33. 2 Use [K / L] to select “Favorites”, then press • Confirmation message will appear. 4 Use [0 / 1] to select “Yes”, then press [ENTER]. • The selected station is removed from “Favorites”. 5 Press [TOP MENU] once to return to the Add Stations on the vTuner Website page 33. 2 Use [K / L] to select “Reset”, then press [ENTER]. 3 Use [0 / 1] to select “Yes”, then press [ENTER].
E1T12ED_EN.book Page 36 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP In the setup menu screen, you can access various kinds of menus, and customise them as you prefer. To call up the setup menu screen, press [SETUP]. Then follow the instructions below to navigate through the screen. < Setup menu screen > Quick 1 2 3 Mode Select Disc Audio Output Speakers HDMI Video Resolution Auto Component Output 480i/576i Player Menu English 4 1. Quick menu Contains only the frequently used menus. 2.
E1T12ED_EN.book Page 37 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Custom EN Sets the language for DivX® subtitle. If the DivX® subtitle file contains more than one subtitle language, you can toggle those by pressing [SUBTITLE] repeatedly. Sets the aspect ratio of the playback image to fit your TV. Sets the resolution of the video signal being output from the HDMI OUT jack. “Auto”: HDMI video resolution will be selected automatically depending on the connected HDMI device.
E1T12ED_EN.book Page 38 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Category Menus / Options Still Mode Auto Field Frame Custom Video Description Adjusts picture resolution and quality in still mode. “Auto”: Automatically selects the best resolution setting (“Frame” or “Field”) based on the data characteristics of the pictures. “Field”: Stabilises the pictures, although the picture quality may become coarse due to the limited amount of data.
E1T12ED_EN.book Page 39 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Audio Output* • Refer to page 43 for more information. Speakers HDMI Normal HDMI LPCM 0~7 default is 3 Dimension -3~3 default is 0 Panorama On Off Test Tone Off Manual Auto Front Lch Center Subwoofer Front Rch -10dB ~ Surround +10dB Rch Surround Lch Default EN default is 0 default is 0 default is 0 default is 0 default is 0 default is 0 Sets the volume level of all speakers to the default setting.
E1T12ED_EN.book Page 40 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Category Audio Menus / Options Speaker Setup Delay Time • This is a parameter for optimizing the timing at which the sound outputs from the speakers according to the distance from the listening position. Distance Front Center Surround Description Feet Meters 0 to 4.5 m (Default : 0.9 m) 0 to 4.5 m (Default : 0.9 m) 0 to 4.5 m (Default : 0.
E1T12ED_EN.book Page 41 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Your registration code is : VVVVVVVVVV To learn more visit www.divx.com/vod Deactivation Code Your deactivation code is : VVVVVVVV To learn more visit www.divx.com/vod Deactivation Yes No EN OTHERS Enable(Custom) FUNCTION SETUP fun-Link(HDMI CEC) On • This feature is Off available only when the display device is connected with an HDMI cable, and when it supports fun-Link(HDMI CEC) feature.
E1T12ED_EN.book Page 42 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Category Menus / Options Network Connection Enable(Custom) Custom Others Connection Auto Speed 10BASE Half 10BASE Full 100BASE Half 100BASE Full BD-Live Allow Setting Limited Allow Prohibit MAC Address Disable Disclaimer Software Update • Refer to page 49 for more information.
E1T12ED_EN.book Page 43 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP A “Custom” [SETUP] A “Video” A “TV Aspect” Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture. Descriptions of each setting are as follows: Your TV 4:3 4:3 Pan & Scan To enjoy 16:9 picture on 4:3 monitor: Both sides of the picture are trimmed to fit the 4:3 TV without distorting the aspect ratio of the picture.
E1T12ED_EN.
E1T12ED_EN.book Page 45 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP [SETUP] A “Custom” A “Parental” 1 Use [K / L] to select “ ”, then press [ENTER]. • Password input field appears. 2 If a password has not been set, follow A). 3 Select the desired item to set the rating level 4 for, then press [ENTER]. Select the desired rating level, then press [ENTER]. All Sets no limit.
E1T12ED_EN.book Page 46 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Press [ENTER] to go to the list of network status confirmation screen. System Audio Control When you set your TV to output the audio from the 5.1ch speakers through this unit, you can control the volume level or mute the audio using TV’s remote control. (For more details, refer to the owner's manual of your TV.) Others Connection Test IP Address Subnet Mask Default Gateway Primary DNS Secondary DNS then press ‘ENTER’.
E1T12ED_EN.book Page 47 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP 4 Press [RETURN] to go back to the previous screen, or press [SETUP] to exit. Note IP Address Setting / DNS Setting 1 Follow steps 1 to 4 in “Connection Test” on page 46. 2 Use [K / L] to select “Enable(Custom)”, then 3 press [ENTER]. Use [K / L] to select “IP Address Setting”, then press [ENTER] repeatedly to select the desired setting.
E1T12ED_EN.book Page 48 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP 4 Press [RETURN] to go back to the previous screen, or press [SETUP] to exit. Note • The range of input numbers for the port number is between 0 and 65535. (If you enter a number larger than 65535, it will be regarded as 65535.) • For proxy port, certain ports might be closed, blocked or unusable depending on your network environment. Connection Speed You can set connection speed as your preference. (The default setting is “Auto”.
E1T12ED_EN.book Page 49 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP [SETUP] A “Custom” A “Others” Network Update A “Software Update” Current Version You can confirm the current software version. 5 Note press [ENTER]. 3 Use [K / L] to select “Yes”, then press [ENTER]. • This unit will then start checking for the latest software version. 4 Confirmation message will appear. Select “Yes”, then press [ENTER]. • The unit will start downloading the latest software version.
E1T12ED_EN.book Page 50 Tuesday, August 3, 2010 5:13 PM FUNCTION SETUP Initialise [SETUP] A “Initialize” Initialise the setting or SD Memory Card. 1 In stop mode, press [SETUP]. 2 Use [K / L] to select , then press [ENTER]. 3 Use [K / L] to select a desired option, then press [ENTER]. “Setup”: Resets the setup menu to the default. The setting for “Parental”, “Network Connection” and “Mode Select” will not be reset. “Format SD Card”: (Available only when an SD Memory Card is inserted.
E1T12ED_EN.book Page 51 Tuesday, August 3, 2010 5:13 PM Troubleshooting If the unit does not perform properly when operated as instructed in this manual, check the unit, consulting the following checklist. Problem No power. Completely distorted picture or black / white picture with BD / DVD. No sound or distorted sound. No 5.1-channel audio from the speaker system. - When I press the [SURROUND] button on my HTS remote while playing movies, I only get “Off” and “2.
E1T12ED_EN.book Page 52 Tuesday, August 3, 2010 5:13 PM OTHERS Problem The unit does not respond to the remote control. Buttons do not work or the unit stops responding. The unit does not respond to some operating commands during playback. The unit cannot read BD / DVD/ CD. Angle does not switch. Playback does not start when the title is selected. The password for rating level has been forgotten. Cannot connect to the network. Cannot connect to the network while my PC is connected to the network.
E1T12ED_EN.book Page 53 Tuesday, August 3, 2010 5:13 PM OTHERS DivX® An electrical signal that directly represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also “Digital Audio”. DivX® is a codec (compression/decompression) that can compress pictures to a very small amount of data.
E1T12ED_EN.book Page 54 Tuesday, August 3, 2010 5:13 PM OTHERS HDMI (High-Definition Multimedia Interface) Region Code A digital interface between audio and video source. It can transmit component video, audio, and control signal with one cable connection. Hub Regions associate discs and players with particular areas of the world. This unit will only play back discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel.
E1T12ED_EN.
E1T12ED_EN.book Page 56 Tuesday, August 3, 2010 5:13 PM OTHERS Specifications Signal system Power requirements Power consumption Total output power (Amplifier) Dimensions (width x height x depth) Weight Operating temperature Operating humidity General NTSC/PAL colour 220 - 240 V AC, 50 Hz 70 W (standby: 0.7 W) Home theater mode: 1000 W FTC* output power: 700 W *(Main Ch @ 1 kHz within 10% THD, Sub Ch 60 Hz within 2.5% THD) 435 x 59 x 297 mm Total weight: 12.50 kg Main unit: 3.
E1T12ED_EN.book Page 57 Tuesday, August 3, 2010 5:13 PM OTHERS INTRODUCTION Network Service Disclaimer CONNECTIONS Content and services made available through this product are transmitted by third parties by means of networks and transmission facilities over which Company has no control and third party services may be terminated or interrupted at any time, and Company makes no representation or warranty that any content or service will remain available for any period of time.
E1T12ED_EN.
E1T12ED_EN.
E1T12ED_EN.book Page 60 Tuesday, August 3, 2010 5:13 PM DECLARATION OF CONFORMITY This product complies with the requirement of the related directives. We: FUNAI ELECTRIC EUROPE Sp. z o.o. ul. Inżynierska 1, 67-100, Nowa Sól, Poland declare that the following product: Home Theater System Model: HT2-M200 Trade Name: Funai is in compliance with the related regulations. Web Site: http://www.funai.eu © 2010-2011 FUNAI ELECTRIC All rights reserved.
