Introduction OWNER’S MANUAL Basic Setup / TV View Operation TD6D-D500GB Connections HDD & DVD / VIDEO CASSETTE RECORDER Recording PAL SECAM Playback Editing Function Setup VCR Functions EN 1 Others For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
. Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This product consists of materials which can be recycled and reused if disassembled by a specialised company. Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, after heating a cold room, or under conditions of high humidity. Do not use the unit for at least 2 hours to allow the inside to dry. About Copyright Unauthorised copying, broadcasting, public performance and lending of discs are prohibited.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license. Kodak and KODAK Picture CD Compatible are trademarks of Kodak used under license. DVB is a registered trademark of the DVB Project is a trademark of DVD Format/Logo Licensing Corporation.
Accessories Supplied Remote control with 2 R6 (1.5 V) batteries RF cable Owner’s Manual CD-ROM Warranty Card The following features are available with this unit.
Table of Contents Introduction ...................................................... 2 Editing ............................................................. 58 Precautions ........................................................................ 2 Guide to a Title List .......................................................... 58 Features ............................................................................. 5 Editing Discs ....................................................................
Introduction Guide to the Owner’s Manual Symbols Used in the Owner’s Manual Symbol HDD DVD-V VR DVD-RW DVD-R Available to (internal) HDD Available to DVD-videos Available to DVD-RW discs in video mode Available to DVD-RW discs in VR mode Available to DVD-R discs in video mode Available to audio CDs MP3 Available to CD-RW/-R discs and USB device with MP3 files JPEG Available to CD-RW/-R discs and USB device with JPEG files DivX Available to DVD-RW/-R, CD-RW/-R discs and USB device with DivX® files
Media for Recording / Playing Media Type DVD-RW DVD-R HDD Automatically formatted in video mode - Logo Format Can be formatted in VR or video mode Video Mode Icon Maximum Record Time VR Mode Video VR DVD-RW DVD-RW 480 min (12 cm) 144 min (8 cm) 480 min (12 cm) 144 min (8 cm) 1×-6× Recordable/Playable Ver. 1.1/1.2 Versions Ver. 1.1/1.2 CPRM compatible Available Features Playable on most DVD players. Compatibility Finalisation necessary.
Introduction Discs for Playing Disc Type DVD-VIDEO CD-DA CD-RW CD-R Logo Icon CD CD CD Connections DVD-V Files for Playing Type of title MP3 JPEG DivX® Icon MP3 JPEG DivX CD-RW/-R USB device CD-RW/-R USB device CD-RW/-R DVD-RW/-R USB device (not guaranteed) The following discs will not play back on this unit. • CD-ROM 2 Following discs are recommended for good recording quality and are proven to be compatible with this unit.
Functional Overview Front Panel 1 2 3 4*1 25*3 23*2 21*2 19 18 17 24 22*2 20 5 6 7 16 14 12 10 11*1 15 13 9 8 You can also turn on the unit by pressing these buttons. You can turn on the unit by pressing these buttons only when a videotape is in this unit. Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the AC power cord.
20 21 22 SYSTEM (YELLOW) button (VCR) SEARCH (BLUE) button (VCR) 3 5 6 26 27 7 28 8 29 9 30 10 13 14 15 33 34 35 16 17 18 36 37 38 19 39 Function Setup 31 32 Editing 11 12 Playback 24 25 REV E button PLAY B button SKIP H button (HDD/DVD) VCR button PAUSE F button TIME SHIFT button (HDD) DUBBING button SUBTITLE button 1.3x/0.8x PLAY button (HDD/DVD) HDMI button OPEN\CLOSE EJECT A button (DVD/VCR) PROG. G \ H buttons TIMER PROG.
Installing Batteries in the Remote Control Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment. 1 2 Device select indicators buttons • Incorrect use of batteries can result in hazards such as leakage and bursting. • Do not mix new and old batteries together. • Do not use different kinds of batteries together.
Guide to On-Screen Displays
Title name information DISPLAY Menu HDD Title Name DVD My Title T 1/ 5 C 1/ 5 0:01:00 / 1:23:45 VR ORG (only when VR mode DVD-RW, unfinalised video mode DVD-RW/-R disc or HDD is in playback) 8 2 File name information 1 TF1 Basic Setup / TV View Operation 1 -RW 3 Connections With a disc inserted into the unit, press [DISPLAY] to display the on-screen display.Main Menu VCR While in the VCR mode, the on screen display of the VCR mode is displayed. Press [VCR] first. Press [DISPLAY] to display the on screen display. Press [SETUP] to display the main menu. Then use [K \ L] to select a menu and press [ENTER\OK] to display the sub menu. Press [RETURN\BACK] to return to previous screen. . 1 2 STEREO 3 12:00 AV2 7 6 SP 0:00:00 STEREO 5 4 5 6 7 A 1 2 B 3 C 4 D 5 E F 6 G H 4 This is an example screen for explanation.
To programme a timer recording. [E Page 33] Introduction B Timer Programming G DISC Playback Mode Audio CD DISC Playback Mode C Title List 1 2 To call up the title list.
Front Panel Display Guide 1 2 DTV 3 DB 4 1 DTV indicator : Appears when a videotape is in this unit. : Appears when the channel is in digital mode. : Appears when a disc is in this unit. 2 Title / Track and Chapter number : : 3 Title / track number Chapter number DB : 4 Current status of the unit F: Appears when playback is paused. Appears during step by step playback. B: Appears when playing back an HDD or disc. F B: Appears during slow forward / reverse playback.
Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, unplug your TV and this unit Antenna RF cable (not supplied) 1 To Aerial jack Audio IN Component video IN RF cable (supplied) Y PB/CB PR/CR IN jack of this unit. 2 Connect the ANTENNA OUT jack of this unit to the Aerial jack of your TV.
Using an HDMI Compatible Port [HDMI CONNECTION] • HDMI outputs the video / audio signals without converting to analogue signals. • No audio connections is required. • Use the HDMI cable (commercially available) for connection. • Connect the HDMI output jack of this unit to the HDMI input jack of TV. HDMI cable (not supplied) To HDMI input jack HDMI IN this unit TV Selecting HDMI video resolution Press [HDMI] to select the HDMI video resolution.
Digital Audio for Better Sound Quality Dolby Digital decoder, DTS decoder or MPEG decoder, etc. Digital audio input jack COAXIAL Recording from a DVD player, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2) Connections This unit has three input terminals. Press [INPUT SELECT] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1, AV2 or DV(AV3). Be sure that all the units are switched off before making connections.
Basic Setup / TV View Operation 6 Initial Setting After finishing channel setting, “Clock Setting” will appear. Clock Setting When you turn on this unit for the first time, you need to follow these steps. 1 2 06 / 01 / 2012 (FRI) 0 : 00 Press [STANDBY-ON Q]. • The current date and time will appear automatically. • If the current date and time are correct, press [RETURN\BACK] to exit, if they are incorrect, press [ENTER\OK] and follow to “A Clock Setting” on page 71. Turn the TV on.
ANALOG Programme the tuner to scan only the analogue channels you can receive in your area. 2 Select “Channel” using [K \ L], then press [ENTER\OK]. Channel Setting 3 You can retune this unit or edit the channel setting with following methods. Select “ANALOG Channel Setup” using [K \ L], then press [ENTER\OK]. 4 Select “Auto Tuning” using [K \ L], then press [ENTER\OK]. Auto Tuning (DVB & ANALOG) DVB The unit will start storing channels available in your area.
6 Select the position number you want to use using [the Number buttons] or [K \ L], then press [0]. • You can select position number 1-99. • With [the Number buttons], you only need to enter the last 2-digit numbers. 7 8 Select “System” using [K \ L], then press [1]. Skip a Preset Channel ANALOG You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H]. 1 Follow steps 1 to 4 in “Manual Tuning (ANALOG)” on page 21.
Manual Tuning (DVB) DVB DVB You can programme the tuner to scan only the DVB channels that you can receive in your area. 2 Select “Channel” using [K \ L], then press [ENTER\OK]. 3 Select “DVB Channel Setup” using [K \ L], then press [ENTER\OK]. 4 Select “Auto Tuning” using [K \ L], then press [ENTER\OK]. 1 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 23. 2 Select “Manual Tuning” using [K \ L], then press [ENTER\OK].
Quick Select TV View Operation DVB The following operations are available while viewing TV channels through this unit’s tuner. 1 Select a Channel DVB With “Quick Select” menu, you can select your favourite DVB channel quickly. Refer to “Edit Group Lists” on page 25. ANALOG Press [ENTER\OK] while watching a DVB channel. • “Quick Select” menu will appear. To switch DVB, analogue and external input (AV1/AV2/ DV(AV3)) mode. Press [INPUT SELECT] repeatedly to select DVB, analogue or external input mode.
Press [RETURN\BACK] to exit. Adult Lock Edit Group Lists DVB You can set the unit to limit the access to the DVB channels. DVB 1 2 1 Follow steps 1 to 4 in “Edit Channels” on page 24. 2 Select the DVB channel you want to limit the access using [K \ L], then press [YELLOW]. Follow steps 1 to 4 in “Edit Channels” on page 24. Edit Channels S.No.
Channel Move Signal Information DVB DVB You can change the order of the DVB channels when you use [PROG. G \ H]. You can check the detailed information of the current DVB channel. 1 Follow steps 1 to 4 in “Edit Channels” on page 24. 1 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 23. 2 Select the DVB channel you want to change the position using [K \ L], then press [ENTER\OK]. 2 Select “Signal Information” using [K \ L], then press [ENTER\OK]. Pop up window will appear.
Select “Stereo”, “Left” or “Right” using [0 \ 1]. • The available audio language varies depending on the DVB programmes. 4 Press [ENTER\OK] to activate the settings. Subtitle While viewing a DVB programme, press [SUBTITLE]. In stop mode, press [SETUP]. Select “Timer Programming” using [K \ L], then press [ENTER\OK]. 2 Select “EPG” using [K \ L], then press [ENTER\OK]. • Select the channel and TV programme using [K \ L \ 0 \ 1].
Recording Restrictions on Recording Information on DVD Recording Type of Discs This unit can record on DVD-RW/-R discs. DVD-RW discs allow you to record programmes repeatedly, and the recorded contents can be erased. There are 2 recording formats: VR mode and video mode. VR and video modes are available for DVD-RW discs while as only video mode is available for DVD-R discs. Video mode is the same recording format as used on the prerecorded DVD-videos you purchase in local shops.
Introduction Making Discs Playable in Other DVD Players (Finalise) After recording, you must finalise the disc to play it back in other players. (See page 45.) You cannot finalise discs in other DVD recorders. Disc Type DVD-R DVD-RW Video Mode VR Mode ✔ ✔ ✔ ✔ ✔ After finalising ✔ Undo finalising (See page 45.) Additional recording or editing (See page 45.
Formatting a Disc 3 Select “Aspect Ratio (Video mode)” using [K \ L], then press [ENTER\OK]. 4 Select your desired setting using [K \ L], then press [ENTER\OK]. Choosing the Recording Format of a Blank DVD-RW Disc Video DVD-RW DVD-RW When inserting a brand-new DVD-RW disc, the unit automatically starts to initialise the disc. DVD-RW disc will be formatted either video or VR mode according to the recording format mode setting of the unit.
Video Select “Stereo” or “Bilingual” using [K \ L], then press [ENTER\OK]. VR DVD-RW DVD-RW If you use a DVD-RW disc, you can format the disc by performing “Format”. You can format DVD-RW disc for either video mode recording or VR mode recording. • When you reformat the disc, the contents of the disc are erased. • Make sure that the recording format is set to the desired mode. (Refer steps 1 to 6 in “Choosing the Recording Format of a Blank DVD-RW Disc” on page 30.
Note One-touch Timer Recording (OTR): • “PCM” stands for Pulse Code Modulation. It changes analogue sound to digital sound without compressing audio data. • When the recording speed is set at other than XP, the unit records “Dolby Digital” audio automatically even if you selected “PCM”. This is a simple way to set the recording time in blocks of 30 minutes. Check that the disc you are recording onto has enough space remaining for the time you set. (See page 74 for VCR recording.
DVB 5 Select the digital (DVB) / analogue (ATV) mode or external input (AV1/AV2) using [K \ L], then press [1]. 6 Select the channel number to record using [K \ L], then press [1]. 7 Select the recording media (“HDD” or “DVD”) using [K \ L], then press [1]. 8 Select the recording speed using [K \ L], then press [1]. ANALOG Video VR HDD DVD-RW DVD-RW DVD-R You can set the unit to record up to 36 programmes, up to a month in advance. Daily or weekly programme recordings are also available.
Note • If you have not set the clock, the clock setting window will appear instead of the Timer Programming list. Continue from “A Clock Setting” on page 71 before programming the timer. • Press [K \ L] to move the cursor in “Timer Programming” list.
The error number appears on “Timer Programming” list. Timer Programming 10:00 MON 14/05 Start End CH 7:00 9:00 1 TF1 New Programme STTL VPS/PDC The error programme will be displayed in grey with an error number. The error numbers indicate: E1–E22, E37–E39 Recording error Unrecordable disc E25/E51 • Copy prohibited programme • Cannot record because of the NTSC / PAL-60 signal is received.
Priority of overlapped settings The unit records programmes according to priority if the timer programmes overlap. Timer Recording (EPG) DVB If the starting time is same: • The timer programming set first (PROG. 1) has priority. PROG. 2 recording will start after PROG. 1 recording is completed. PROG. 1 PROG. 2 Actual recording PROG. 1 PROG. 2 Video DVD-RW DVD-RW DVD-R With EPG system, you can programme DVB channel recording much easier. You can only choose one programme and enter the selection.
Satellite Link HDD You can set the unit to start recording whenever it detects the video scart control from the external tuner. [Preparation of this unit] • Make sure to select the desired recording speed beforehand. Example 1 Timer Recording Satellite Link Actual Recording Recording External tuner (not supplied) Basic Setup / TV View Operation [Preparation of the external tuner] • The external tuner should be equipped with some kind of timer function.
Recording from External Equipment Settings for External Equipment Video Colour System When you record from external equipment or copy a videotape to an HDD/DVD disc, you can set the format Auto, PAL or SECAM. 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK]. 3 Select “Video Colour System” using [K \ L], then press [ENTER\OK]. 4 Select “Auto”, “PAL” or “SECAM” using [K \ L], then press [ENTER\OK].
1 2 • With “Control” highlighted, press [ENTER\OK] to display the available devices to control with the remote control of this unit. Select the device you want to operate using [K \ L], then press [ENTER\OK]. - Select “HDD” / “DVD” to control this unit with the remote control of this unit. - Select “DVC” to control your DVC with the remote control of this unit. Guide to DV and On-Screen Display 2 Press [INPUT SELECT] repeatedly to select the external input channel, then press [PROG.
To stop dubbing: DVC to HDD / DVD Dubbing Video VR HDD DVD-RW DVD-RW DVD-R Before recording from DVC, see page 19 for connection instructions. (See page 75 for DVC to VCR Dubbing.) Preparing for DV dubbing (DVC to HDD): • Make sure your DVC is in video mode. Preparing for DV dubbing (DVC to DVD): • Insert a recordable DVD. • Make sure your DVC is in video mode. If you want to record to the HDD, press [HDD] first. If you want to record to a disc, press [DVD] first.
Information on Dubbing Difference between “Copy” and “Move”: Copy : After dubbing the programme, the original programme will remain.
Before Starting Dubbing One Touch Dubbing Video HDD to DVD / DVD to HDD You can copy the contents between HDD and DVD. Limitation (DVD to HDD): • If a copy control signal is detected during dubbing, the dubbing will be stopped. VR VCR DVD-RW DVD-RW DVD-R You can start dubbing right away with just one touch. HDD One Touch Dubbing between HDD and DVD Preparing for dubbing (HDD to DVD): • Insert a recordable DVD. Preparing for dubbing (DVD to HDD): • Insert a disc to be dubbed.
Selected Title Dubbing HDD If you want to record a title in the videotape, press [VCR] first. Press [PLAY B] to start the playback of the videotape you want to dub. Press [STOP C] or [PAUSE F] where you want to start dubbing. 3 Press [DUBBING VCR M DVD] on the front panel. DVD-R VCR In stop mode, press [SETUP]. Select “Dubbing” using [K \ L], then press [ENTER\OK]. Setup General Setting Timer Programming Title List DVD Menu HDD Menu Dubbing The dubbing will start from there to the end.
6 Repeat step 5 until you register all the titles to be dubbed, then press [DUBBING]. Confirmation message will appear. • Depending on the dubbing direction, the available recording speed varies. • When dubbing from HDD to DVD, you can select “High” to perform the high speed dubbing (refer to “Recording Speed for Dubbing” on page 41 for more details). e.g.
Do you want to cancel? Yes No 10% Finalising VR If “No” is selected and [ENTER\OK] or [RETURN\BACK] is pressed, finalising is continued. DVD-RW To prevent accidental over-recording, editing or erasing of recordings, you can protect them using “Setup” menu. Insert a recordable disc. 1 In stop mode, press [SETUP]. Select “DVD Menu” using [K \ L], then press [ENTER\OK]. 3 Select “Disc Protect OFF A ON” using [K \ L], then press [ENTER\OK]. 4 Select “Yes” using [K \ L], then press [ENTER\OK].
Playback 7 Basic Playback Playback will start. For title in the HDD, you can also select “Resume Playback” to play from the resume points. Note for HDD / DVD Playback The contents of an HDD / DVD are generally divided into titles. Titles are further subdivided into chapters depend on Auto Chapter setting (See page 30). Start Rec. Stop Rec./Start Rec. Select “Play From Start” using [K \ L], then press [ENTER\OK]. 8 Press [STOP C] to stop playback.
CD MP3 JPEG DivX ® 2 If you want to play back an audio CD or a disc with a single file type (e.g., a disc containing MP3 files only), skip to step 4. If you want to play back a disc with mixed file types, proceed to step 3. 3 Select the desired file type using [K \ L], then press [ENTER\OK]. 4 Press [K \ L] to select the desired track / file or folder, then press [ENTER\OK]. e.g.
Playing Back a USB Device with MP3 / JPEG / DivX® Files 2 If you want to change the media type, press [0]. Select the desired media type using [K \ L], then press [ENTER\OK]. (You can also access the media type selection screen from the “Title List” in the “Setup” menu in stop mode.) • Video Files: The DivX® File List will appear (not guaranteed). • Music: The MP3 File List will appear. • Photo: The JPEG File List will appear. MP3 JPEG DivX ® You can play back the contents in a USB device.
The subtitle created by the user can be displayed during DivX® playback. After the DivX® file is selected, “Subtitle List” will appear. 2 Select the desired extension of the subtitle file you want to display using [K \ L], then press [ENTER\OK]. DivX® with the subtitle starts playback. The subtitle cannot be displayed when the setting is “OFF”. • If there is more than one extension, the extension selection will appear in “Subtitle List”. You can get the new registration code and deactivation code.
Note for DivX® • DivX® is a codec (compression/decompression) that can compress images to a very small amount of data. The software can compress video data from almost any sources to the size that can be sent on the Internet without compromising visual quality of the images. • For discs, a file with an extension of “.avi” and “.divx” can be played back as a DivX® file. • Files whose extension other than “.avi” and “.divx” will not be listed on the DivX® menu.
Special Playback Resume Playback HDD Video VR DVD-RW DVD-RW DVD-R MP3 JPEG DivX ® You can resume playback from the point where you stopped it before. 1 Press [PLAY B]. HDD CD 1 For Discs: You can set only one resume point per disc. 2 VR DVD-RW DVD-RW DVD-R MP3 JPEG DivX ® During playback, press [PAUSE F]. Playback will pause with the sound muted. Playback Press [PLAY B] to resume playback.
Step by Step Playback HDD DVD-V Zoom Video VR DVD-RW DVD-RW During playback, press [PAUSE F]. Press [SKIP H \ G] repeatedly. Each time you press [SKIP G], playback will go forward one frame (or step) at a time with the sound muted. To go backward one frame (or step), press [SKIP H]. VR DVD-RW DVD-R 1 During playback, press [DISPLAY] to bring up the display menu. 2 Select the icon using [0 \ 1] to display the selection menu. Press and hold [SKIP G] to continue going forward.
HDD HDD You can play back a title being recorded from the beginning while recording continues. 1 During recording, press [PLAY B]. 2 To stop the playback, press [STOP C] once. To playback a title being recorded while continuing to record, refer to “Chasing Playback during Recording” on page 53 (available only with HDD). The front panel display will switch back to show the elapsed recording time. If you press [STOP C] twice, recording will stop.
Search Title / Chapter Search DVD-V HDD Video VR DVD-RW DVD-RW DVD-R Using [SKIP H \ G] buttons 1 During playback, press [SKIP G] to skip the current title or chapter and move to the next. The unit moves to the next title or chapter one after another. To go back to the previous title or chapter, press [SKIP H] twice in quick successions. Note • With regard to HDD, chapter search using [SKIP H \ G] is available only within the same title.
Repeat / Random / Programme Playback / Slide Show CD You can use this function to play back a disc randomly instead of in the recorded order. Repeat Playback CD 1 3 DVD-RW DVD-RW DVD-R 1 2 MP3 JPEG DivX ® During playback, press [DISPLAY] to bring up the display menu. If the display menu is already shown, skip to step 2. Select the icon using [0 \ 1] to display the selection menu. Select the desired option to repeat using [K \ L], then press [ENTER\OK]. The selected repeat playback will start.
Programme Playback CD You can programme the disc to play back in your desired order. 1 Follow steps 1 to 2 in “Random Playback” on page 55. 2 Select “Programme Play” using [K \ L], then press [ENTER\OK]. 3 Select the desired track using [K \ L], then press [ENTER\OK] or [1]. DISC Playback Mode You can select the format of audio and video to suit the content of the disc you are playing back.
Select a desired audio soundtrack or audio channel using [K \ L], then press [ENTER\OK]. Note DVD-V HDD Video VR DVD-RW DVD-RW During playback, press [DISPLAY] to bring up the display menu. The angle icon appears when a switching camera angle is available. (Available only when the angle icon appears in bottom right on the TV screen.) 2 Select the icon using [0 \ 1], then press [ENTER\OK]. The angle will switch each time you press [ENTER\OK].
Editing 1 2 Guide to a Title List Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer. Press [HDD] or [DVD], then press [TOP MENU]. 2 1 6 ORG Title List ABCDE 11:00 (10:00:00) 17/05/10 125 SP 1 2 3 4 5 6 1/6 Title name. Title information, which displays recorded time, length of the title, date / month / year, recorded CH, and the recording speed.
Editing Discs HDD Note • It is not possible to retrieve deleted titles. If you want to edit the HDD, press [HDD] first. If you want to edit a disc, press [DVD] first. 1 In stop mode, press [TOP MENU]. Title List will appear. For HDD and VR mode DVD-RW disc, press [MENU\LIST] to switch between “Original” and “Playlist”. 2 Select the desired title with [K \ L \ 0 \ 1], then press [ENTER\OK]. Pop up window will appear.
4 Deleting Selected Titles A window for entering the title name will appear. 5 HDD You can delete titles which you do not need anymore. Please be advised that the titles once deleted cannot be brought back. 1 2 Press [HDD], then press [TOP MENU]. 3 Select “Delete Multiple Titles” using [K \ L], then press [ENTER\OK]. Select “Edit Title Name” using [K \ L], then press [ENTER\OK]. To enter the title name, refer to “Guide to Editing Title Names” on page 60.
Adding or Deleting Chapter Marks at once for Video Mode DVD-RW disc VR HDD DVD-RW You can add chapter marks to a title. After a title is marked with chapters, you can use the chapter search feature. You can set a chapter mark anywhere you want. Press [DVD] first. Follow the steps 1 to 3 in “Editing Title Name” on page 60. 1 2 Select “Chapter Mark” using [K \ L], then press [ENTER\OK]. Follow the steps 1 to 3 in “Editing Title Name” on page 60.
4 Press [RETURN\BACK] repeatedly to exit. 4 For DVD, writing onto the disc starts. It may take awhile to write the data on a disc. Select “Yes” using [K \ L], then press [ENTER\OK]. The two titles will combine into a single title. e.g.) VR mode DVD-RW Playlist To protect a whole disc (VR mode DVD-RW disc only): Select “Disc Protect OFF A ON” from “DVD Menu”, then select “Yes”. Refer to “Setting a Disc to Protect” on page 45.
VR HDD DVD-RW All Playlists can be deleted if it is no longer needed. 1 2 5 Select “Yes” using [K \ L], then press [ENTER\OK]. “Are you sure?” will appear. Select “Yes” using [K \ L], and then press [ENTER\OK]. The part of the title is deleted. Press [SETUP]. Select “DVD Menu” (for DVD) or “HDD Menu” (for HDD) using [K \ L], then press [ENTER\OK]. Select “Delete All Playlists” using [K \ L], then press [ENTER\OK]. e.g.) VR mode DVD-RW Select “Yes” using [K \ L], then press [ENTER\OK].
Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation.
Items (highlight is the default) Variable Skip/ Variable Skip Replay E Page 70 Variable Replay Recording Auto Chapter E Page 30 PAL SECAM Clock Setting E Page 71 Auto Clock Setting E Page 72 ON OFF General Setting Set a picture size according to aspect ratio of your TV. Sets the video output mode. Insert chapter marks periodically. Set the recording audio type. (Only when the recording speed is set to “XP”.) Set the unit to finalise the disc automatically.
General Setting Setup Channel DivX Items (highlight is the default) Country E Page 23 Auto Tuning (DVB & ANALOG) E Page 21 DVB Channel Edit Channels Setup E Page 24 Auto Tuning E Page 23 Manual Tuning E Page 23 Signal Information E Page 26 ANALOG Auto Tuning Channel Setup E Page 21 Manual Tuning E Page 21 Move E Page 22 DivX® VOD E Pages 49, 72 France Spain - Peninsula Spain - Canary Islands Germany Italy Switzerland Czech Republic Other Tune the DVB and analogue channels automatically.
Subtitle Contents Set the Adult Lock and change Pincode. ON OFF Lock each DVB programme. Set the Audio language. Set the Subtitle language. Check the current DVB system software version of the unit. Set to the default setting. About E Page 73 Reset All E Page 73 Note • Your change to each settings stays on even when the power is switched off. • An item which is not currently available is greyed in the settings.
Playback Setup A General Setting A Playback A password is already set 1 Enter the current password using [the Number buttons]. A B C D E F G H I Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode Variable Skip/Replay TV System Password Input 2-A Select “No” using [K \ L], then press [ENTER\OK]. Change Password? Yes No A Parental Lock (Default: OFF) (DVD only) “Parental Lock” level is activated.
Settings for MP3 Surround (Default: PCM) MP3 Surround PCM PCM Stream 48kHz 96kHz 48kHz : If your amplifier / decoder is NOT compatible with 96 kHz PCM, select “48kHz”. Sound recorded at 96 kHz is down sampled to 48 kHz. : If your amplifier / decoder is compatible with 96 kHz PCM, select “96kHz”. Sound is sampled at 96 kHz. Note Note • Set to “Stream” when this unit is connected to an amplifier for MP3 Surround. C Disc Menu Language (Default: English) (DVD only) Set “Disc Menu Language”.
I TV System (Default: PAL) (DVD only) Note • You can also change or switch off the subtitles on a DVD from the disc menu if it is available. • Press [CLEAR] or [0] to erase numbers entered incorrectly. • You can only select the languages supported by the inserted disc. F Angle Icon (Default: ON) (DVD only) TV System PAL Auto PAL : Outputs a modified PAL signal for viewing discs recorded with the NTSC system on a PAL system TV.
Introduction 2 Select “Yes” using [0 \ 1], then press Video [ENTER\OK]. Setup A General Setting A Video A TV Aspect B Video Out Final confirmation window will appear. 3 Select “Yes” using [K \ L], then press [ENTER\OK] within 15 seconds. Confirm again to use progressive scan. If picture is good, select “Yes”. Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture.
B Auto Clock Setting (Default: ON) This unit receives time signals from the analogue / DVB channels, and set the clock automatically. Set the channel tuning before setting Auto Clock. B DivX Subtitle (Default: OFF) Set the DivX® subtitle. DivX Subtitle OFF English Czech Dutch French German Hungarian Italian Auto Clock Setting ON OFF 1 Select “ON” using [K \ L], then press [ENTER\OK]. 2 Press [SETUP] to exit. 3 Press [STANDBY-ON Q] to turn the unit off. • The Auto clock function is activated.
Setup A General Setting A DVB Setting You can make settings of the digital tuner from the DVB Setting. DVB Language Audio Subtitle Adult Lock Maturity Lock Language About Audio : Set the Audio language. Subtitle : Set the Subtitle language. A Adult Lock (Default: OFF) DVB 1 Select “ON” or “OFF” using [K \ L], then press [ENTER\OK]. D About Adult Lock ON OFF DVB To set “Adult Lock” to “ON”: 1) Enter your desired Pincode using [the Number buttons], then press [ENTER\OK].
VCR Functions Common Procedures 1 Press [STANDBY-ON Q] to turn on the unit. To play back a tape, turn on the TV and be sure to select the input to which the unit is connected. 2 Basic Recording and One-touch Timer Recording (OTR) VCR Press [VCR]. Before recording, make sure: Playback VCR Note for HDMI, Component and Digital Audio (COAXIAL) Output in VCR Playback This unit can be output with HDMI, Component and Digital Audio (COAXIAL) in VCR playback.
One-touch Timer Recording will start. Normal Recording 8:00 1:00 • Insert a recordable videotape. • Make sure your DVC is in video mode. Press [INPUT SELECT] repeatedly to select the external input channel, then press [PROG. G \ H] repeatedly to select DV(AV3). 2 Select the recording speed using [REC SPEED]. (See page 74.) 3 Stop or pause the DVC where you want to start dubbing. 4 5 Play back the DVC. Prevent accidental erasure Note • Dubbing will start from where the tape is stopped.
Time Search VCR This feature allows you to go to a specific point on a tape by entering the exact amount of time you want to skip in order to reach the point. 1 Press [SEARCH] repeatedly until the time search menu appears. 2 Enter your desired time to skip using [the Number buttons] within 30 seconds. 3 Press [FWD D] or [REV E] to start time search. If you want to go in the forward direction, press [FWD D]. If you want to go in the reverse direction, press [REV E].
Introduction Others Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. Remedy The unit turns on automatically without any operation. • The unit turns on automatically 2 seconds before the timer recording. The unit does not function. • “ ” or error message appears if the operation is prohibited.
Symptom Remedy • Check the HDMI connection. (Check the status of the HDMI related indications.) • Check whether the connected monitor device or other device supports HDCP. (This unit will not output a video signal unless the other device supports HDCP.) • Check the setting of HDMI. • Check whether the output format of this unit (HDMI FORMAT) matches the supported input format of other connected device.
Remedy • Check if the playable disc is inserted. • Check if the disc is loaded correctly with the labelled side facing up. • Discs made on other devices or on personal computers cannot be played back on this unit unless it is finalised on the device. • Even if it is finalised, the performance of those discs are not guaranteed on this unit. • The disc may be dirty or flawed. Clean the disc. • Check if all the connections are made correctly. • Check “Parental Lock” setting. (See page 68.
HDD / DVD EDITING DVD Symptom Remedy Titles cannot be edited or deleted. • The titles or the disc itself may be protected. Cancel the protection by following the steps on pages 61-62 for title protection and page 45 for disc protection. Dubbing cannot be executed. • When the number of the titles or the chapters exceeds the maximum recordable number, the dubbing will not be executed. Titles cannot be edited or deleted. • The titles in the DVD-R cannot be edited or deleted if they are finalised.
Cause Introduction Error message Solution • Insert a recordable disc with enough recording space. • Delete unnecessary original titles. (See page 59.) Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99) • You are trying to record onto the DVD-RW / -R disc on which the number of recorded titles has reached the maximum (99). • Delete unnecessary original titles. (See page 59.) Recording Error You cannot record more than 999 chapters on one disc.
Language Code Language 82 Code Language Code Language Code Language Code Abkhazian 4748 French 5264 Lithuanian 5866 Sindhi 6550 Afar 4747 Frisian 5271 Macedonian 5957 Singhalese 6555 Afrikaans 4752 Galician 5358 Malagasy 5953 Siswat 6565 Albanian 6563 Georgian 5747 Malay 5965 Slovak 6557 Amharic 4759 German 5051 Malayalam 5958 Slovenian 6558 Arabic 4764 Greek 5158 Maltese 5966 Somali 6561 Armenian 5471 Greenlandic 5758 Maori 5955 Spanish 5165
Introduction Specifications General Four heads HDD Internal 3.5 inch HDD 500 GB Power requirements 220–240 V Power consumption 48 W Power consumption (standby) 0.93 W Weight 5.8 kg Connections VCR video heads ± 10 %, 50 Hz ± 0.5 % 435 x 99.
Declaration Conformity This product complies with the requirement of the related directives. We: FUNAI ELECTRIC EUROPE Sp. z o.o. ul. Inżynierska 1, 67-100, Nowa Sól, Poland declare that the following product: HDD & DVD / Video Cassette recorder Model TD6D-D500GB Trade Name: Funai is in compliance with the related regulations. Web Site: http://www.funai.eu © 2012 FUNAI ELECTRIC All rights reserved. Printed in P.R.C.