INTRODUCTION Owner’s Manual INITIAL SETTING V7PFDVD20 CONNECTION 20” Digital / Analog Television built-in DVD Player WATCHING TV OPTIONAL SETTING OPERATING DVD DVD SETTING OPEN/CLOSE VIDEO VOLUME CH. STOP SELECT L - AUDIO - R HEADPHONE TROUBLESHOOTING POWER PLAY INFORMATION TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
INTRODUCTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. RADIO-TV INTERFERENCE LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
INTRODUCTION LOCATION For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
INTRODUCTION 5 Contents DVD Functions INTRODUCTION Basic Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 INFORMATION Glossary . . . . . . . . . . . . . . . . .
INTRODUCTION 5 Features TV • DTV/TV/CATV - You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable subscribers can access their cable TV channels. • Program Information Display (DTV only) - You can display the title, contents and other information of the current DTV program on the TV screen. • Auto Channel Scan - This unit automatically scans and memorizes channels available in your area, eliminating difficult setup procedures.
INTRODUCTION 5 Remote Control Function 4. 14 3 4 5 21 9 22 10 11 23 15. 16. 17. 18. 19. 20. 21. 22. 23. TROUBLESHOOTING 5 Installing the Batteries Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control. 2 3 INFORMATION 1 DVD SETTING POWERy y button (p11) Press to turn the unit on and off. PICTURE/SLEEP button (p15 / p16) • Press to adjust the picture quality. • Press to activate the sleep timer.
INTRODUCTION 5 Control Panel 1. POWER OPEN/CLOSE VIDEO VOLUME CH. STOP SELECT L - AUDIO - R HEADPHONE PLAY POWER OPEN/CLOSE VIDEO VOLUME CH. STOP SELECT L - AUDIO - R HEADPHONE PLAY 1 2 3 4 5 6 7 8 9 10 11 HEADPHONE jack Headphone connection for personal listening. 2. AUDIO input jacks (p10) RCA audio cable connection for an external device. 3. VIDEO input jack (p10) RCA video cable connection for an external device. 4. OPEN/CLOSE A button (p23) Press to open or close the disc tray. 5.
INTRODUCTION CONNECTION Cables not included. Please purchase the necessary cables at your local store. CONNECTION 5 Basic Connection This section describes how to connect the unit to an antenna, cable/satellite box, etc. Note: • Be sure your antenna or other device is connected properly before plugging in the power cord.
CONNECTION Cables not included. Please purchase the necessary cables at your local store. 5 External Device Connection [Video Cable Connection] When you connect this unit to an external device, use the audio/video input jacks on the front of this unit. Make the connection as illustrated below. When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack. front of this unit e.g.
These operations are accessible by remote control. Some may also be accessible by controls on the main unit. INTRODUCTION INITIAL SETTING TV Functions Note: This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and “AUTO PRESET CH”, which automatically scans and memorizes viewable channels. Make sure if the unit is connected to antenna or cable. 1 After making all the necessary connections, press [POWERy] to turn on the unit.
INITIAL SETTING 5 Auto Channel Scan Note: If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you recover the DTV channel you deleted, you will need to perform auto channel scan. Before you begin: Make sure if the unit is connected to antenna or cable. 1 Press [SET-UP] to display the main menu. 2 Use [Cursor K/L] to select “CHANNEL SETUP”, then press [ENTER]. e.g.
INTRODUCTION WATCHING TV 5 Channel Selection 5 Volume Adjustment Select channels by pressing [CH. K / L] or [the Number buttons]. This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described. CONNECTION • To select the memorized channels, use [CH. K / L] or [the Number buttons]. • To select the non-memorized channels, use [the Number buttons]. Use [VOL. X / Y] to adjust the audio volume.
WATCHING TV 5 Switching Each Mode DTV You can easily switch with the remote control to the DTV (ATSC), TV (NTSC) and DVD mode or to access an external device when they are connected to the unit. Press [SELECT] repeatedly to cycle through the input mode. In the digital mode, the detailed broadcasting information for the current channel such as program title, the program guides are displayed. Press [DISPLAY] repeatedly to cycle through the available display modes.
INTRODUCTION 5 TV Screen Display Mode 5 Sleep Timer The sleep timer can be set to automatically turn off the unit after an incremental period of time. DTV 1 Press [SET-UP] to display the main menu. CONNECTION 2 types of display modes can be selected in the digital mode when the broadcasting station is sending 16:9 video signal. 1 Press [PICTURE/SLEEP] once. INITIAL SETTING 2 Use [Cursor K / L] to select “DTV SETUP”, then press [ENTER]. SLEEP e.g.
OPTIONAL SETTING 5 Channel Add/Delete 5 Picture Adjustment The channel add/delete function lets you add the channel that was not added by the auto channel scan due to the reception status at the initial setting. You can also delete the unnecessary channels. You can adjust brightness, contrast, color, tint and sharpness. 1 Press [SET-UP] to display the main menu. 1 Press [PICTURE/SLEEP] repeatedly until the desired picture menu appears.
INTRODUCTION 5 Closed Caption Note: TV 1 Press [SET-UP] to display the main menu. [ENTER] repeatedly to change the setting. e.g.) digital TV mode --- TV SETUP --- or CAPTION1 CAPTION2 OPTIONAL SETTING OFF WATCHING TV CHANNEL SETUP V-CHIP SETUP LANGUAGE [ENGLISH] CAPTION [OFF] DTV SETUP INITIAL SETTING 2 Use [Cursor K / L] to select “CAPTION”, then press CONNECTION You can view closed captioning (cc) for TV programs, movies and news.
OPTIONAL SETTING 5 DTVCC Style 5 DTV Closed Caption DTV DTV In addition to the basic closed caption described on page 17, DTV has its own closed caption called DTVCC. Use this menu to change the settings for DTVCC. You can change the style of DTV CC such as font, color or size, etc. 1 Press [SET-UP] to display the main menu. 1 Press [SET-UP] to display the main menu. 2 Use [Cursor K / L] to select “DTV SETUP“, then press 2 Use [Cursor K / L] to select “DTV SETUP“, then press [ENTER] . [ENTER]. e.
INTRODUCTION 5 V-chip V-chip reads the ratings for programs, then denies access to the programs which exceed the rating level you set. With this function, you can block certain programming inappropriate for children. • CHARACTER EDGE Edge type of the displayed caption can be switched as below. 1 Press [SET-UP] to display the main menu. 2 Use [Cursor K / L] to select “V-CHIP SETUP“, then press [ENTER]. e.g.
OPTIONAL SETTING A. TV Rating [To Set the Sub Ratings] As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further set the sub ratings to block specific elements of programming. To set the sub ratings, follow the steps below. 4 Use [Cursor K / L] to select “TV RATING“, then press [ENTER]. e.g.) digital TV mode --- V--CHIP SETUP --- or 1 Use [Cursor K / L] to select the desired main rating, TV RATING MPAA RATING DOWNLOADABLE RATING CHANGE PASSWORD then press [ENTER] twice to show its sub ratings.
C. Change Password Although the default code “0000” is supplied with the unit, you can set your own password. 4 Use [Cursor K / L] to select “MPAA RATING”, 4 Use [Cursor K / L] to select CONNECTION MPAA Rating is the rating system created by MPAA (Motion Picture Association of America). then press [ENTER]. INTRODUCTION B. MPAA Rating “CHANGE PASSWORD”, then press [ENTER]. e.g.) digital TV mode e.g.
OPERATING DVD DVD Functions 5 Playable Media Type of media Mark (logo) DVD-video *1, 2, 4, 6, 10, 11 DVD-RW DVD-R * 1, 3, 4, 5, 6, 7, 8, 9, 10 DVD+RW DVD+R * 1, 4, 5, 6, 9, 10 audio CD * 4, 6, 10 Region code 1 Recorded signals Media size Disc types or ALL - e. g.) digital video (MPEG2) title 1 title 2 chapter 1 chapter 2 chapter 3 chapter 4 chapter 1 chapter 2 5 inches (12 cm) or 3 inches (8 cm) e. g.
5 Playback INTRODUCTION These operations are accessible by remote control. Some may also be accessible by controls on the main unit. Note: Turn on the amplifier and any other device which is connected to this unit. Make sure the external audio receiver (not supplied) are set to the correct input mode. 5 Disc Menu DVD 2 Press [OPEN/CLOSE A]. • The unit switches to the DVD mode when the unit was in TV mode. Press [DISC MENU] to call up the disc menu, or press [TITLE] to call up the title menu.
OPERATING DVD 5 Step-by-step Playback 5 Zoom DVD DVD The zoom function allows you to enlarge the video image and to pan through the enlarged image. Each time you [PAUSE F] in the pause mode, the disc goes forward one frame at a time. 1 During playback, press [MODE] repeatedly until “ ” appears. To continue playback, press [PLAY B]. OFF (ZOOM) Note: • Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in the pause mode are blurred. (Refer to page 33.
INTRODUCTION 5 Search Functions Chapter / Title Search CONNECTION DVD Track Search CD Using [MODE] Using [MODE] playback, press [MODE] repeatedly until 1 During “ “ appears. 1 During playback, press [MODE] repeatedly until “ “ appears. INITIAL SETTING • If you want to perform the title search, press [Cursor K / L] repeatedly until “ “ appears. 2 Press [the Number buttons] to select your desired 2 track within 60 seconds.
OPERATING DVD 5 Repeat Playback You can repeat playback chapters, titles or tracks on a disc. Time Search 1 During playback, press [MODE] repeatedly until “ 1 During playback, press [MODE] repeatedly until “ “ /“ “ appears. e.g.) DVD /12 (SEARCH) 2 Use [Cursor K / L] repeatedly until “ TOTAL or “ appears. 2 Press [Cursor K / L] to change the repeat mode. DVD “ appears.
2 Use [Cursor K / L] to select a desired track, then press [ENTER] to store. • Additional tracks may be on other screens. Use [Cursor K/ L] to go on to the next / previous pages. • Repeat this step until you have selected all the tracks you wish to play back in the program. or PROGRAM TOTAL 0:08:22 T 15 3:18 T 16 4:24 ALL CLEAR T 4 T 16 3:58 4:24 PLAY CLEAR CD 1 In stop mode, press [MODE] repeatedly until “RANDOM” menu appears. 1/ 1 T 16 4:24 • Up to 99 tracks can be ordered.
OPERATING DVD 5 On-screen Display You can check the information about the current disc by pressing [DISPLAY] on the remote control.
INTRODUCTION 5 Special Settings Subtitle Language Audio Language This unit allows you to select a subtitle language (if available) during DVD playback. This unit allows you to select an audio language (if multiple languages are available) during DVD playback. 1 During playback, press [MODE] repeatedly until 1 During playback, press [MODE] repeatedly until “ “ appears. “ appears. 2 Use [Cursor K / L] repeatedly until the desired language appears. language appears. 1.ENG Dolby D 3/2.
OPERATING DVD Black Level Setting Virtual Surround You can enjoy virtual surround on your existing 2 channel stereo system. DVD Adjust the black level to make the dark areas of the TV picture brighter. 1 During playback, press [MODE] repeatedly until 1 During playback, press [MODE] repeatedly until 2 Use [Cursor K / L] to adjust the black level. 2 Use [Cursor K / L] to select the sound level. “ “ appears. “ “ appears. OFF (BLACK LEVEL) or ON : Makes the dark areas brighter.
INTRODUCTION Marker Setup To return to the marker later To set a marker 1 During playback, press [MODE] repeatedly until “ ”/“ CONNECTION This feature allows you to assign a specific point on a disc to be called back later. ” appears. 1 To select a desired marker, repeat steps 1 to 3 in “To set a marker“. e.g.) DVD INITIAL SETTING e.g.) DVD /12 (SEARCH) 2 Use [Cursor K /L] repeatedly until marker search menu 2 Press [ENTER] at the desired marker to start playback appears.
DVD SETTING Settings are only effective when the unit is in DVD mode and any discs should not be played back. QUICK MENU AT A GLANCE If you make setting for “TV MODE“ or “DOLBY DIGITAL”, you can also enter from the “QUICK“ menu. In stop mode, press [SET-UP] to display the “SETUP” menu first, then use [Cursor K /L] to select “QUICK” and press [ENTER]. SETUP 5 Use [Cursor K /L] to select the desired item, then press [ENTER]. [AUDIO] *1, *2 (Default: ORIGINAL) Select the desired audio language.
INTRODUCTION 5 Display Setting You can change the TV aspect ratio and still mode clarity in “DISPLAY” menu. 5 Use [Cursor K /L] to select the desired item, then press [ENTER]. [TV MODE] (Default: 4:3 LETTER BOX) Select the desired TV aspect ratio. SETUP or [ENTER].
DVD SETTING 5 DVD Audio Setting Choose the appropriate audio settings for your device. It only affects during the playback of DVD. 1 In stop mode, press [SET-UP] to display “SETUP” menu. 2 Use [Cursor K /L] to select “CUSTOM”, then press 5 Use [Cursor K /L] to select the desired item, then press [ENTER]. [DRC] (dynamic range control) (Default: ON) Select “DRC”. This function is available only on the discs which are recorded in the Dolby Digital format. [ENTER].
6 Use [Cursor K /L] to select the desired item, then press [ENTER]. SETUP or 1 In stop mode, press [SET-UP] to display “SETUP” menu. PARENTAL PARENTAL LEVEL ALL 8 [ADULT] 7 [NC-]7 6 [R] 5 [PGR] 4 [PG13] 3 [PG] SELECT:K/L EXIT:SETUP SETUP or SET:ENTER CANCEL:RETURN SELECT:K/L EXIT:SETUP PARENTAL LEVEL ALL : All parental locks are canceled. 8 [ADULT] : All ratings (adult/general/children) can be played back. 7 [NC-17]-2 [G] : Only DVD intended for general use and children can be played back.
DVD SETTING 5 Others 5 Use [Cursor K /L] to select the desired item, then press You can change the other functions. [ENTER]. 1 In stop mode, press [SET-UP] to display “SETUP” menu. [ANGLE ICON] (Default: ON) Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback. SETUP or 2 Use [Cursor K /L] to select “CUSTOM”, then press OTHERS ANGLE ICON AUTO POWER OFF ON ON [ENTER].
5 Language Code List You can reset all the settings except for the parental setting and on-screen menu language. Language [ENTER]. SETUP or QUICK CUSTOM INITIALIZE SET:ENTER CANCEL:RETURN SETUP or INITIALIZE Initialize? NO YES SELECT:K/L EXIT:SETUP SET:ENTER CANCEL:RETURN • When you want to cancel the initialization, select “NO” at step 3, then press [SET-UP].
TROUBLESHOOTING 5 Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service. Symptom Remedy No power • Be sure the power cord is plugged in. • If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to reset itself. No picture or sound • Check if the power is on. • Check the outlet connection. • Check the antenna or cable connection to the main unit.
INTRODUCTION • Many digital channels have alternate channel numbers. The unit changes the numbers automatically to the ones signifying the broadcasting stations. These are the numbers used for analog broadcasts. Remote control does not work • Check the antenna or cable connection to the main unit. • Check the batteries of the remote control. • Check if there is an obstacle between the infrared sensor window and the remote control. • Test the signal output. If OK, then possible remote sensor trouble.
INFORMATION 5 Glossary ATSC HDTV (high definition TV) Region Code Acronym that stands for Advanced Television Systems Committee and the name of the digital broadcasting standards. Ultimate digital format that produces high resolution and high picture quality. Aspect Ratio Acronym that stands for National Television Systems Committee and the name of the current analog broadcasting standards. Regions associate discs and players with particular areas of the world.
INTRODUCTION 5 Cable Channel Designations If you subscribe to cable TV, the channels are displayed as 1-135. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations.
INFORMATION 42 EN
INTRODUCTION CONNECTION INITIAL SETTING WATCHING TV OPTIONAL SETTING OPERATING DVD DVD SETTING TROUBLESHOOTING INFORMATION EN 43
LIMITED WARRANTY This form describes the protection You will have under this Limited Warranty. LIMITED WARRANTY PERIOD: This Limited Warranty begins on the date of purchase of the Covered Product and continues for a period of six months. WHAT IS COVERED: Meijer will pay the cost of labor and repair or replacement parts in the event Your Covered Product fails to operate as a result of a mechanical or electrical failure caused by defects in workmanship and/or materials.