Operation Manual

33
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions
Basic Setup /
TV View Operation
Timer Recording
You can set the unit to record up to 12 programmes, up to a
month in advance. Daily or weekly programme recordings are
also available.
• Be sure to set the clock before entering a timer
programming.
Insert a recordable disc or a tape with a record tab.
1 In stop mode, press [TIMER PROG.].
“Timer Programming” list will appear.
2 Select “New Programme” using [K \ L], then
press [ENTER\OK].
• If there are 6 programmes or more, use
[SKIP H \ G] to turn the page.
3 Enter the date using [K \ L], then press [1].
Each time you press [L] at the current date, the timer
recording date will change as follows.
e.g., 1st January
• Analogue channel is indicated as “ATV”.
4 Enter the time to start and to end using [K \ L],
then press [1].
5 Select the digital (DVB) / analogue (ATV) mode
or external input (AV1/AV2) using [K \ L], then
press [1].
6 Select the channel number to record using
[K \ L], then press [1].
7 Select the recording media (“DVD” or “VCR”)
using [K \ L], then press [1].
8 Select the recording speed using [K \ L], then
press [1].
Refer to “Recording Speed” on page 28 for DVD or
page 70 for VCR.
Select “STTL” to “ON” or “OFF” using [K \ L].
If you set “STTL” to “ON”, subtitle will be recorded too.
• When analogue channel is selected, “VPS/PDC” will be
displayed instead of “STTL”.
Select “VPS/PDC” to “ON” or “OFF” using
[K \ L].
Refer to “VPS (Video Programme System) / PDC
(Programme Delivery Control)” on page 34.
• When DVB channel is selected, “STTL” will be displayed
instead of “VPS/PDC”.
• VPS/PDC system is not available for “Daily” and “M-F”
timer programme.
10 Press [ENTER\OK] when all information
required is entered.
Your programme setting is stored.
• To set another programme, repeat steps
2 to 10.
• To exit, press [TIMER PROG.].
• When 2 or more programmes are overlapped, “Timer
programme overlapped” appears, and the overlapped
programme will be displayed in blue. To correct the timer
programme, refer to “Checking, Cancelling or Correcting
the Timer Programming Information” on page 34.
11 Press [TIMER SET] to set a timer programming.
Front panel display stays off while the unit is in the
standby mode.
DVB ANALOG
DVD-RW
DVD-RW
DVD-RW
Video
DVD-RW
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
DVD-R
VCR
VCR
1/1
20/05
21/05
7:00
9:00
9:00
9:30
DVB 18
DVB 190
Timer Programming
Date Start End CH
STTL
VPS/PDC
New Programme
0:00 MON 17/05
01/01
Daily
M-F (Mon.-Fri.)
W-SAT
W-FRI
W-SUN
31/01
Timer Programming
1/1
0:00 MON 17/05
Date
REC To
Speed
STTL
Start End CH
DVD 2H OFF
--:-- --:-- DVB 10
2H 2:00
20/05
9 For DVB channel recording:
For analogue channel recording:
1/1
20/05
21/05
22/05
7:00
9:00
17:00
9:00
9:30
18:00
DVB 18
DVB 190
1 TF1
0:00 MON 17/05
Timer Programming
Date Start End CH
New Programme
STTL
VPS/PDC
E9TF0ED_EN.book Page 33 Wednesday, March 17, 2010 1:32 PM