Introduction OWNER’S MANUAL Basic Setup / TV View Operation WD6D-M101 Connections DVD / VIDEO CASSETTE RECORDER Recording PAL SECAM Playback Editing Function Setup VCR Functions EN 1 Others For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
. Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This product consists of materials which can be recycled and reused if disassembled by a specialised company. Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, after heating a cold room, or under conditions of high humidity. Do not use the unit for at least 2 hours to allow the inside to dry. About Copyright Unauthorised copying, broadcasting, public performance and lending of discs are prohibited.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license. CLEANING DISCS If a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion.
Accessories Supplied Remote control with 2 R6 (1.5 V) batteries RF cable Owner’s Manual CD-ROM Warranty Card DVD • • • • The following features are available with this unit.
Table of Contents Introduction ...................................................... 2 Editing ............................................................. 54 Precautions ........................................................................ 2 Guide to a Title List .......................................................... 54 Features ............................................................................. 5 Editing Discs ....................................................................
Introduction Guide to the Owner’s Manual Symbols Used in the Owner’s Manual Symbol DVD-V Video DVD-RW DVD-R CD Description Available to DVD-videos Available to DVD-RW discs in video mode Available to DVD-RW discs in VR mode Available to DVD-R discs in video mode Available to audio CDs Available to CD-RW/-R discs and USB device with MP3 files JPEG Available to CD-RW/-R discs and USB device with JPEG files DivX Available to DVD-RW/-R, CD-RW/-R discs and USB device with DivX® files (DivX® files in USB
Media for Recording / Playing Media Type DVD-RW DVD-R Logo Automatically formatted in video mode Format Can be formatted in VR or video mode Video Mode Icon Maximum Record Time VR Mode Video VR DVD-RW DVD-RW 480 min (12 cm) 144 min (8 cm) 480 min (12 cm) 144 min (8 cm) 1×-6× Recordable/Playable Ver. 1.1/1.2 Versions Ver. 1.1/1.2 CPRM compatible Available Features Playable on most DVD players. Compatibility Finalisation necessary. (Title menu will be created) 1×-16× Ver. 2.0/2.
Introduction Discs for Playing Disc Type DVD-VIDEO CD-DA Logo Icon CD Connections DVD-V Files for Playing Type of title MP3 JPEG DivX® Icon MP3 JPEG DivX CD-RW/-R USB device CD-RW/-R USB device CD-RW/-R DVD-RW/-R USB device (not guaranteed) This unit has been designed to play DVD with region 2. If these region symbols do not appear on your DVD, you cannot play back the DVD in this unit. The number inside the globe refers to region of the world.
Functional Overview Front Panel 1 2 3*1 4 5 5V 21*3 19*2 17*2 16 15 14 20 18*2 13 12 10 11 8 9*1 500mA 7 6 You can also turn on the unit by pressing these buttons. You can turn on the unit by pressing these buttons only when a videotape is in this unit. Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the AC power cord.
19 20 21 SYSTEM (YELLOW) button (VCR) SEARCH (BLUE) button (VCR) 3 5 6 25 26 7 27 8 28 9 29 10 16 17 35 36 37 18 38 Note • If you turn off this unit, [OPEN\CLOSE EJECT A] on the remote control is not available. Be sure to use [OPEN\CLOSE A] or [STOP\EJECT C A] on the unit. VCR Functions Button names described in the Owner’s Manual The instructions in this manual are described mainly with the operations using the remote control.
Installing Batteries in the Remote Control Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment. 1 2 Caution button About the Remote Control • Make sure there is no obstacle between the remote control and the remote control sensor on the unit. • Use within the operating range and angle as shown.
Guide to On-Screen Displays Introduction Press [DISPLAY] repeatedly while the display menu is displayed to display the following information.
Title name information DISPLAY Menu Title Name DVD My Title T 1/ 5 C 1/ 5 0:01:00 / 1:23:45 1 -RW 3 VR ORG (only when VR mode DVD-RW, unfinalised video mode DVD-RW/-R disc is in playback) File name information 8 2 File Name My File Basic Setup / TV View Operation 5 6 Connections Press [DVD] first.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-14.html>PAGE 14</a></h6><p>INFO Menu VCR While in the VCR mode, the on screen display of the VCR mode is displayed. Press [VCR] first. Press [DISPLAY] to display the on screen display. DVB Press [C] while viewing a DVB programme to display the programme information. . 3 1 2 STEREO 3 12:00 AV2 7 6 SP 0:00:00 5 STEREO 4 This is an example screen for explanation. Displayed items are depending on the actual mode.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-15.html>PAGE 15</a></h6><p>Introduction Main Menu B Timer Programming Press [SETUP] to display the main menu. Then use [K \ L] to select a menu and press [ENTER\OK] to display the sub menu. Press [RETURN\BACK] to return to previous screen. To programme a timer recording. [E Page 33] C Title List To call up the title list.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-16.html>PAGE 16</a></h6><p>Front Panel Display Guide 1 2 DTV DB VCR 3 DVD 4 1 DTV indicator : Appears when a videotape is in this unit. : Appears when the channel is in digital mode. : Appears when a disc is in this unit. 2 Title / Track and Chapter number : : 3 DB : Title / track number Chapter number Appears during dubbing. DVD :Appears when this unit is in DVD output mode, or the timer-standby mode for DVD recording. Current status of the unit Appears when playback is paused. Appears during step by step playback.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-17.html>PAGE 17</a></h6><p>Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, unplug your TV and this unit Antenna RF cable (not supplied) 1 To Aerial jack Audio IN Component video IN RF cable (supplied) Y PB/CB PR/CR IN jack of this unit. 2 Connect the ANTENNA OUT jack of this unit to the Aerial jack of your TV.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-18.html>PAGE 18</a></h6><p>Using an HDMI Compatible Port [HDMI CONNECTION] • HDMI outputs the video / audio signals without converting to analogue signals. • No audio connections is required. • Use the HDMI cable (commercially available) for connection. • Connect the HDMI output jack of this unit to the HDMI input jack of TV. HDMI cable (not supplied) To HDMI input jack HDMI IN this unit TV Selecting HDMI video resolution Press [HDMI] to select the HDMI video resolution.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-19.html>PAGE 19</a></h6><p>Recording from a DVD player, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2) Digital Audio for Better Sound Quality Dolby Digital decoder, DTS decoder or MPEG decoder, etc. Digital audio input jack COAXIAL Connections This unit has three input terminals. Press [INPUT SELECT] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1, AV2 or DV(AV3). Be sure that all the units are switched off before making connections.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-20.html>PAGE 20</a></h6><p>Basic Setup / TV View Operation 6 Initial Setting After finishing channel setting, “Clock Setting” will appear. Clock Setting When you turn on this unit for the first time, you need to follow these steps. 1 2 01 / 01 / 2013 (TUE) 0 : 00 Press [STANDBY-ON Q]. • The current date and time will appear automatically. • If the current date and time are correct, press [RETURN\BACK] to exit, if they are incorrect, press [ENTER\OK] and follow to “A Clock Setting” on page 68. Turn the TV on.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-21.html>PAGE 21</a></h6><p>3 Select “Auto Tuning (DVB & ANALOG)” using [K \ L], then press [ENTER\OK]. The unit will start storing channels available in your area. General Setting Selecting the TV Aspect Ratio Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Video” using [K \ L], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-22.html>PAGE 22</a></h6><p>[BG (PAL-B/G)] Note Channel Plan CH Indication TV Channel 2 – 12 E2 - E12 13 – 20 A – H (only ITALY) 21 – 69 E21 – E69 74 – 78 X, Y, Z, Z+1, Z+2 80 – 99, 100 S1 – S20, GAP 121 – 141 S21 – S41 • The number of TV channels you can get is different depends on your local area. • If the auto tuning is cancelled during scanning, some channels not yet tuned may not be received. • When “Country” setting is set to “France”, sorting of TV channels from 1 to 6 will be performed automatically as follows.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-23.html>PAGE 23</a></h6><p>DVB You can programme the tuner to scan only the DVB channels that you can receive in your area. 4 Introduction • When “Auto” is selected, the unit will search for the channels which have not been stored in channels memory. Auto Tuning (DVB) Press [SETUP] to activate the setting. Service Update Select “Channel” using [K \ L], then press [ENTER\OK]. 3 Select “DVB Channel Setup” using [K \ L], then press [ENTER\OK]. 1 In stop mode, press [SETUP].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-24.html>PAGE 24</a></h6><p>Quick Select Group: All TV View Operation S.No. Channel Name 2 Channel4 3 ITV2 4 ITV3 13 Channel4+1 19 More4 28 ITV4 29 E4 The following operations are available while viewing TV channels through this unit’s tuner. Select a Channel DVB ANALOG To switch DVB, analogue and external input (AV1/AV2/ DV(AV3)) mode. Press [INPUT SELECT] repeatedly to select DVB, analogue or external input mode. The mode changes as follows: DVB mode Analogue mode External input mode (with [PROG.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-25.html>PAGE 25</a></h6><p>Adult Lock DVB DVB You can sort each DVB channel into 8 different favourite group lists (“Group 1” - “Group 8”). With “Quick Select” menu, you can select your favourite DVB channel quickly. Refer to “Quick Select” on page 24. 2 Select the DVB channel you want to add to the favourite group list using [K \ L], then select the number of the favourite group list you want to add using [the Number buttons] ([1] - [8]). Follow steps 1 to 4 in “Edit Channels” on page 24.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-26.html>PAGE 26</a></h6><p>Channel Move Signal Information DVB DVB You can change the order of the DVB channels when you use [PROG. G \ H]. You can check the detailed information of the current DVB channel. 1 Follow steps 1 to 4 in “Edit Channels” on page 24. 1 Follow steps 1 to 3 in “Auto Tuning (DVB)” on pages 23. 2 Select the DVB channel you want to change the position using [K \ L], then press [ENTER\OK]. 2 Select “Signal Information” using [K \ L], then press [ENTER\OK]. Pop up window will appear.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-27.html>PAGE 27</a></h6><p>EPG (Electronic Programme Guide) DVB DVB Many DVB channels transmit Multi Audio information along with their DVB channels. You can select the desired audio mode and audio language. While viewing a DVB programme, press [AUDIO]. Multi Audio English French Spanish Select “Stereo”, “Left” or “Right” using [0 \ 1]. Select your desired audio language using [K \ L]. • The available audio language varies depending on the DVB programmes. 4 Press [ENTER\OK] to activate the settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-28.html>PAGE 28</a></h6><p>Recording Restrictions on Recording Information on DVD Recording Type of Discs This unit can record on DVD-RW/-R discs. DVD-RW discs allow you to record programmes repeatedly, and the recorded contents can be erased. There are 2 recording formats: VR mode and video mode. VR and video modes are available for DVD-RW discs while as only video mode is available for DVD-R discs. Video mode is the same recording format as used on the prerecorded DVD-videos you purchase in local shops.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-29.html>PAGE 29</a></h6><p>Introduction Making Discs Playable in Other DVD Players (Finalise) After recording, you must finalise the disc to play it back in other players. (See page 41.) You cannot finalise discs in other DVD recorders. Disc Type DVD-R DVD-RW Video Mode VR Mode ✔ ✔ ✔ ✔ ✔ After finalising Undo finalising (See page 41.) Additional recording or editing (See page 41.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-30.html>PAGE 30</a></h6><p>4 Formatting a Disc Select your desired setting using [K \ L], then press [ENTER\OK]. Aspect Ratio (Video mode) Choosing the Recording Format of a Blank DVD-RW Disc Video Auto 4:3 16 : 9 Auto: It will be recorded with whichever the ratio that the programme you started to record is broadcasted with. 4:3 : Recorded with the aspect ratio of 4:3. 16:9 : Recorded with the aspect ratio of 16:9. VR DVD-RW DVD-RW When inserting a brand-new DVD-RW disc, the unit automatically starts to initialise the disc.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-31.html>PAGE 31</a></h6><p>Select “DVD Menu” using [K \ L], then press [ENTER\OK]. 3 Select “Format” using [K \ L], then press [ENTER\OK]. 4 Select “Start” using [K \ L], then press [ENTER\OK]. A pop up window will appear and prompt you to confirm. 5 Select “Yes” using [K \ L], then press [ENTER\OK]. e.g.) VR mode DVD-RW 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-32.html>PAGE 32</a></h6><p>• When the unit reaches the specified time, it will be turned off automatically. • To change the recording length during One-touch Timer Recording, press [REC] repeatedly until the desired length appears. • To cancel One-touch Timer Recording within the specified time, press [STOP C]. Basic Recording and One-touch Timer Recording (OTR) DVB ANALOG Video VR DVD-RW DVD-RW DVD-R Follow the steps below to record a TV programme. (See page 71 for VCR recording.) 1 Press [STANDBY-ON Q] to turn on the unit.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-33.html>PAGE 33</a></h6><p>DVB 5 Select the digital (DVB) / analogue (ATV) mode or external input (AV1/AV2) using [K \ L], then press [1]. 6 Select the channel number to record using [K \ L], then press [1]. 7 Select the recording media (“DVD” or “VCR”) using [K \ L], then press [1]. 8 Select the recording speed using [K \ L], then press [1]. ANALOG Video VR VCR DVD-RW DVD-RW DVD-R You can set the unit to record up to 12 programmes, up to a month in advance. Daily or weekly programme recordings are also available.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-34.html>PAGE 34</a></h6><p>Note • If you have not set the clock, the clock setting window will appear instead of the Timer Programming list. Continue from “A Clock Setting” on page 68 before programming the timer. • Press [K \ L] to move the cursor in “Timer Programming” list. • If a basic recording or One-touch Timer Recording is in progress on one component (e.g. VCR) and the timer recording set for the other component (e.g.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-35.html>PAGE 35</a></h6><p>E1–E22, E37–E39 Recording error Unrecordable disc E25/E51 • Copy prohibited programme • Cannot record because of the NTSC / PAL-60 signal is received. E26–E28 Copy prohibited programme E29 Disc protected If the starting time is same: • The timer programming set first (PROG. 1) has priority. PROG. 2 recording will start after PROG. 1 recording is completed. PROG. 1 PROG.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-36.html>PAGE 36</a></h6><p>Timer Recording (EPG) Satellite Link You can set the unit to start recording whenever it detects the video scart control from the external tuner. DVB Video VR DVD-RW DVD-RW DVD-R With EPG system, you can programme DVB channel recording much easier. You can only choose one programme and enter the selection. Refer to “EPG (Electronic Programme Guide)” on page 27.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-37.html>PAGE 37</a></h6><p>Introduction Note Settings for External Equipment Video Colour System When you record from external equipment or copy a videotape to a DVD disc, you can set the format Auto, PAL or SECAM. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK]. Satellite Link 3 Select “Video Colour System” using [K \ L], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-38.html>PAGE 38</a></h6><p>When you want to record to a videotape: Press [VCR]. Insert a videotape with a record tab into the cassette compartment. 3 Select the input terminal to which the external equipment is connected (AV1 or AV2). 3 Press [DISPLAY] to display the DVC information on the screen. When the DVC is in video mode... T 1 2 1/ 1 -RW Control DV Audio Start Rec Press [INPUT SELECT] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1 or AV2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-39.html>PAGE 39</a></h6><p>Status of the current operation and the time counter 4 Each icon means (Available icons may vary depending on the DVC): With “Control” highlighted, press [ENTER\OK] to display the available devices to control with the remote control of this unit. Select “DVC” using [K \ L], then press [ENTER\OK]. e.g.) DVC to DVD dubbing DVC is in stop mode. DVC is in playback mode. T 1/ 1 C 1/ 1 -RW DVC is fast forwarding. (standard speed) DVC is fast forwarding.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-40.html>PAGE 40</a></h6><p>• This unit will automatically stop the duplication if playback with no image detected for more than 3 minutes during VCR to DVD duplication. • If the playback sound mode of VCR is set to “STEREO”, “LEFT” or “RIGHT”, the sound mode upon dubbing is automatically switched to “STEREO”. If the playback sound mode is set to “MONO”, the sound mode upon dubbing is also “MONO”. • If you set “External Input Audio” to “Stereo”, the sound is recorded in “Stereo” (video mode and VR mode).</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-41.html>PAGE 41</a></h6><p>VR DVD-RW To prevent accidental over-recording, editing or erasing of recordings, you can protect them using “Setup” menu. Insert a recordable disc. 1 In stop mode, press [SETUP]. Select “DVD Menu” using [K \ L], then press [ENTER\OK]. 3 Select “Disc Protect OFF A ON” using [K \ L], then press [ENTER\OK]. If “ ” appears when [STOP C] is pressed, you cannot cancel finalising because the finalising has already reached at a critical point in its process.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-42.html>PAGE 42</a></h6><p>Playback 9 To eject the disc, press [OPEN\CLOSE EJECT A] to open the disc tray, then remove the disc. Press [OPEN\CLOSE EJECT A] to close the disc tray before turning off the unit. Basic Playback Note for DVD Playback The contents of a DVD are generally divided into titles. Titles are further subdivided into chapters depend on Auto Chapter setting (See page 30). Start Rec. Stop Rec./Start Rec. Title 1 Press [STOP C] to stop playback. Stop Rec.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-43.html>PAGE 43</a></h6><p>Press [K \ L] to select the desired track / file or folder, then press [ENTER\OK]. e.g.) Photo (JPEG) files File List DISC NAME Notes on JPEG: After file is displayed for 5 seconds or 10 seconds (set in the “Slide Show” on page 52), the display moves to the next file. During JPEG playback, press [1] or [0] to rotate a picture 90 degrees clockwise or counterclockwise respectively. (Not available when the display menu appears.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-44.html>PAGE 44</a></h6><p>1 In stop mode, plug your USB flash memory. If all menu items cannot be displayed in the screen scope, the A appears at the right bottom and the R appears at the left bottom of the screen and you can view other items on the next or previous page. The track number of the items currently played back is highlighted. If the A is shown at the right bottom, use [SKIP G] to view the next page. If the R is shown at the left bottom, use [SKIP H] to view the previous page.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-45.html>PAGE 45</a></h6><p>DivX [DivX®] • Official DivX® Certified product • Playable Codec of AVI files : DivX®3.x, DivX®4.x, DivX®5.x, DivX®6.x • Maximum size of image : 720 x 480 @30 fps 720 x 576 @25 fps • Sampling frequency of audio : 16 kHz - 48 kHz • Audio type : MPEG1 audio layer 3 (MP3), MPEG1 audio layer 2, Dolby Digital ® This unit allows you to play back the files purchased or rented from DivX® Video-On-Demand (VOD) services. The files are available on the Internet.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-46.html>PAGE 46</a></h6><p>• You can play back the disc recorded in multi-session. • It may take awhile for audio and images to be output after you inserted a disc and pressed [PLAY B]. • When playing back the files recorded in high bit rates, the images can be interrupted in some occasions. • Although DivX® logo has been obtained for this unit, it may not be able to play back some data, depending on the characteristics, bit rates, or audio format settings, etc. • Use the software recognised by the DivX, Inc.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-47.html>PAGE 47</a></h6><p>Special Playback Video VR DVD-RW DVD-R 1 MP3 JPEG DivX ® During playback, press [STOP C]. The resume message will appear. 2 Press [PLAY B]. In a few seconds, playback will resume from the point at which you stopped it before. Even if you turn off the unit, you can resume playback at the same point after turning back on the unit. DVD-V CD 1 Video VR DVD-RW DVD-RW DVD-R MP3 JPEG DivX ® During playback, press [PAUSE F].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-48.html>PAGE 48</a></h6><p>3 Step by Step Playback DVD-V 1 2 Video VR DVD-RW DVD-RW The zoom area is displayed. DVD-R DivX ® 4 During playback, press [PAUSE F]. Press [SKIP H \ G] repeatedly. Press and hold [SKIP G] to continue going forward. To continue going backward, press and hold [SKIP H]. Press [PLAY B] to resume playback. Note • To cancel the zoom function, select “x1.0” using [K \ L], then press [ENTER\OK]. • If selecting a smaller factor than that currently selected, the zoom area is not displayed.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-49.html>PAGE 49</a></h6><p>Simultaneous Playback and Recording VR DVD-RW 1 During recording, press [DISPLAY]. T 1/ 5 C 1/ 5 The resume message will appear. To stop recording, press [STOP C] again. To cancel the resume, press [STOP C] again. ORG 1 TF1 Select icon using [0 \ 1], then press [ENTER\OK]. The title number next to will be highlighted. Title: Enter a desired title number to search using [K \ L] or [the Number buttons], then press [ENTER\OK]. Selected title playback will start.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-50.html>PAGE 50</a></h6><p>Search Title / Chapter Search DVD-V Video VR DVD-RW DVD-RW DVD-R Using [SKIP H \ G] buttons 1 During playback, press [SKIP G] to skip the current title or chapter and move to the next. The unit moves to the next title or chapter one after another. To go back to the previous title or chapter, press [SKIP H] twice in quick successions. Using the [DISPLAY] button 1 During playback, press [DISPLAY] to bring up the display menu. 2 Select the icon using [0 \ 1], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-51.html>PAGE 51</a></h6><p>Repeat / Random / Programme Playback / Slide Show CD You can use this function to play back a disc randomly instead of in the recorded order. Repeat Playback Video VR DVD-RW DVD-RW DVD-R CD 1 2 MP3 JPEG DivX ® 1 3 “DISC Playback Mode” or “USB Playback Mode” menu will appear. 3 Select “Music” using [K \ L], then press [ENTER\OK] twice. JPEG files: The selected repeat playback will start. The following operations are available.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-52.html>PAGE 52</a></h6><p>Note • To erase tracks you selected, press [CLEAR]. • You can make up to 50 track settings. • To cancel programme playback, press [STOP C] twice during programme playback. “OFF” appears on the screen. • You may also select the desired track using [the Number buttons] at step 3. • During programme playback, if you forward the track to the end, the playback speed of the next track will be normal. • During programme playback, you cannot use the search function except for the search with [SKIP H \ G].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-53.html>PAGE 53</a></h6><p>Select a desired audio soundtrack or audio channel using [K \ L], then press [ENTER\OK]. Note DVD-V Video VR DVD-RW DVD-RW During playback, press [DISPLAY] to bring up the display menu. The angle icon appears when a switching camera angle is available. (Available only when the angle icon appears in bottom right on the TV screen.) 2 Select the icon using [0 \ 1], then press [ENTER\OK]. The angle will switch each time you press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-54.html>PAGE 54</a></h6><p>Editing 1 Guide to a Title List Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer. Press [DVD], then press [TOP MENU]. 4 5 6 Title list: List of titles recorded on the disc. Each title is indicated by its index picture. Index picture for the selected title can be seen in motion. Following icons may be displayed on the index picture. 2 : Indicating the title is protected.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-55.html>PAGE 55</a></h6><p>Editing Discs Note • It is not possible to retrieve deleted titles. Press [DVD] first. 1 Title List will appear. For VR mode DVD-RW disc, press [MENU\LIST] to switch between “Original” and “Playlist”. 2 Select the desired title with [K \ L \ 0 \ 1], then press [ENTER\OK]. Pop up window will appear. 3 Select “Title Delete” using [K \ L], then press [ENTER\OK]. e.g.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-56.html>PAGE 56</a></h6><p>Editing Title Name Video Guide to Editing Title Names VR DVD-RW DVD-R DVD-RW You can edit the title names from this menu. The title names you edit will appear on the title list. Press [DVD] first. 1 Step 1 : Select the desired character set using [K \ L], then press [ENTER\OK]. Step 2 : Using the list below as a guide, press [the Number buttons] repeatedly until the desired letter appears. In stop mode, press [TOP MENU]. Select Press Title List will appear.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-57.html>PAGE 57</a></h6><p>Select “Add” or “Delete” accordingly using [K \ L], then press [ENTER\OK]. You cannot delete the first chapter of a title. 5 Select “Yes” using [K \ L], then press [ENTER\OK]. Deleting a chapter mark: If you select “Delete” at step 4, the chapter mark you selected is deleted. 6 Press [RETURN\BACK] repeatedly to exit. Note • Maximum numbers of chapter for each media: VR mode DVD : 999 chapters per entire Playlist and Original Press [DVD] first.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-58.html>PAGE 58</a></h6><p>4 Select “Yes” using [K \ L], then press [ENTER\OK]. Adding Titles to a Playlist The title is divided into two new titles with the same title names. 5 Press [RETURN\BACK] to exit. VR DVD-RW Original For VR mode DVD-RW disc, you can add a title to the Playlist as you want. Writing onto the disc starts. It may take awhile to write the data on a disc. Press [DVD] first.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-59.html>PAGE 59</a></h6><p>Introduction Deleting Parts of Titles VR DVD-RW You can delete a specific part of a title. Even when a title is deleted from the Playlist, the original title will remain as it is. Press [DVD] first. 2 Select “Scene Delete” using [K \ L], then press [ENTER\OK]. 3 Use [SKIP H \ G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to find the start point, then press [ENTER\OK]. Basic Setup / TV View Operation Follow the steps 1 to 3 in “Editing Title Name” on page 56.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-60.html>PAGE 60</a></h6><p>Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-61.html>PAGE 61</a></h6><p>Items (highlight is the default) OSD Language E Page 66 General Setting Recording Auto Chapter E Page 30 Main Sub Stereo Bilingual Auto PAL SECAM Clock Setting E Page 68 Auto Clock Setting E Page 68 ON OFF Insert chapter marks periodically. Set the recording audio type. (Only when the recording speed is set to “1H”.) Set the unit to finalise the disc automatically. Set a aspect ratio for video mode recording. Set the dubbing selection. Set the audio type for recording.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-62.html>PAGE 62</a></h6><p>General Setting Setup Channel DivX Items (highlight is the default) Country E Page 23 Auto Tuning (DVB & ANALOG) E Page 21 DVB Channel Edit Channels E Page 24 Setup Auto Tuning E Page 23 Manual Tuning E Page 23 Signal Information E Page 26 Service Update E Page 23 ANALOG Auto Tuning Channel Setup E Page 21 Manual Tuning E Page 22 Move E Page 22 Antenna Out E Page 70 DivX® VOD E Pages 45, 68 France Spain - Peninsula Spain - Canary Islands Germany Italy Switzerland Czech Republic Other Tune the DVB and</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-63.html>PAGE 63</a></h6><p>Subtitle Contents Set the Adult Lock and change Pincode. ON OFF Lock each DVB programme. Set the Audio language. Set the Subtitle language. Check the current DVB system software version of the unit. Set to the default setting. About E Page 70 Reset All E Page 70 Note • Your change to each settings stays on even when the power is switched off. • An item which is not currently available is greyed in the settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-64.html>PAGE 64</a></h6><p>Playback Setup A General Setting A Playback A password is already set 1 Enter the current password using [the Number buttons]. A B C D E F G H Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System Password Input 2-A Select “No” using [K \ L], then press [ENTER\OK]. Change Password? Yes No A Parental Lock (Default: OFF) (DVD only) “Parental Lock” level is activated. 2-B Select “Yes” using [K \ L], then press Set “Parental Lock” level.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-65.html>PAGE 65</a></h6><p>Settings for MP3 Surround (Default: PCM) MP3 Surround PCM PCM Stream 48kHz 96kHz 48kHz : If your amplifier / decoder is NOT compatible with 96 kHz PCM, select “48kHz”. Sound recorded at 96 kHz is down sampled to 48 kHz. : If your amplifier / decoder is compatible with 96 kHz PCM, select “96kHz”. Sound is sampled at 96 kHz. Note Note • Set to “Stream” when this unit is connected to an amplifier for MP3 Surround. C Disc Menu Language (Default: English) (DVD only) Set “Disc Menu Language”.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-66.html>PAGE 66</a></h6><p>Display Note • You can also change or switch off the subtitles on a DVD from the disc menu if it is available. • Press [CLEAR] or [0] to erase numbers entered incorrectly. • You can only select the languages supported by the inserted disc. F Angle Icon (Default: ON) (DVD only) Set to “ON” to show the angle icon during the playback. Setup A General Setting A Display A B C D A OSD Language (Default: English) Set the OSD language.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-67.html>PAGE 67</a></h6><p>Setup A General Setting A Video A TV Aspect B Video Out Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture. TV Aspect 1 Select the desired setting using [K \ L], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-68.html>PAGE 68</a></h6><p>Clock Note Setup A General Setting A Clock A Clock Setting B Auto Clock Setting A Clock Setting Clock Setting 01 / 01 / 2013 (TUE) 0 : 00 1 Enter the date (day / month / year) using [K \ L]. Press [1] to move the cursor to the next field. If you want to go back to the previous field, press [0]. 2 Enter the time (hours / minutes) using [K \ L], then press [ENTER\OK]. The clock will start. • Although seconds are not displayed, they will be counted from zero.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-69.html>PAGE 69</a></h6><p>DVB Setting Setup A General Setting A DVB Setting You can make settings of the digital tuner from the DVB Setting. Format A Adult Lock (Default: OFF) DVB You can set “Adult Lock” to “ON” or “OFF” and also change Pincode. 1 Select “ON” or “OFF” using [K \ L], then press [ENTER\OK]. RGB YCbCr Adult Lock ON OFF B HDMI Audio (Default: ON) 2 To set “Adult Lock” to “ON”: 1) Enter your desired Pincode using [the Number buttons], then press [ENTER\OK].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-70.html>PAGE 70</a></h6><p>C Language DVB Language Audio Subtitle Audio : Set the Audio language. Subtitle : Set the Subtitle language. Note • The Audio and Subtitle setting may not be available for some broadcast. • To change the audio language, refer to “Multi Audio” on page 27. • To display the subtitle or choose the subtitle language, refer to “Subtitle” on page 27. D About DVB You can check the current DVB system software version of this unit.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-71.html>PAGE 71</a></h6><p>Introduction VCR Functions Common Procedures Press [STANDBY-ON Q] to turn on the unit. To play back a tape, turn on the TV and be sure to select the input to which the unit is connected. 2 Basic Recording and One-touch Timer Recording (OTR) VCR Press [VCR]. Before recording, make sure: VCR Note for HDMI, Component and Digital Audio (COAXIAL) Output in VCR Playback 1 Insert a pre-recorded tape, then press [PLAY B] to begin playback. 2 During playback, press [PAUSE F].</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-72.html>PAGE 72</a></h6><p>One-touch Timer Recording: Press [REC] repeatedly until the desired recording time (30 minutes to 8 hours) appears on the TV screen. 3 Stop or pause the DVC where you want to start dubbing. 4 5 Play back the DVC. 0:30 Normal Recording 8:00 Note 1:00 7:30 • When the unit reaches the specified time, it will be turned off automatically. • To change the recording length during One-touch Timer Recording, press [REC] repeatedly until desired length appears.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-73.html>PAGE 73</a></h6><p>VCR To cue or review picture during playback (Picture Search): This unit will distinguish the video colour system (SECAM, PAL or MESECAM) automatically according to the format of a pre-recorded video tape during playback or the input signal from the tuner or external devices. To change the video colour system manually, press [SYSTEM]. Each time you press [SYSTEM], the colour system will change as follows.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-74.html>PAGE 74</a></h6><p>Others Troubleshooting Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. POWER Symptom Remedy The power does not turn on. • Check that the AC power cord is connected securely. • Batteries of the remote control are weak. • Press [TIMER SET] to cancel the timer-standby mode.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-75.html>PAGE 75</a></h6><p>Remedy • Check if the connections are made securely and correctly. • Check if the cables are damaged. • Try “Channel” setting by following the steps on pages 21-23. Some settings are lost even though you • If you unplug the AC mains cable while the warning message, “Saving settings. followed the procedure correctly. Please wait.”, is displayed, some settings may be lost. Do not unplug the AC mains cable while the message is displayed (It will take about 1 minute.). Only specific channels do not appear.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-76.html>PAGE 76</a></h6><p>Symptom Remedy Playback picture is distorted. Colour of the picture is abnormal. • During fast forward or fast reverse, playback picture may be distorted. This is not a malfunction. • Connect to TV directly. When you connect this unit with the television via VCR or other devices, the picture may be distorted due to the copy-protection signal. • Check if the cables are damaged. • Keep the equipment which may cause electrical disturbances, such as a cellular phone, away. There is no sound, or no subtitle.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-77.html>PAGE 77</a></h6><p>DVD EDITING Dubbing cannot be executed. • When the number of the titles or the chapters exceeds the maximum recordable number, the dubbing will not be executed. Titles cannot be edited or deleted. • The titles in the DVD-R cannot be edited or deleted if they are finalised. If it is DVD-RW, undo the finalisation by following the steps on page 41. The capacity of the disc doesn’t increase even if the recorded programme is deleted.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-78.html>PAGE 78</a></h6><p>Error message Cause Solution Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99) • You are trying to record onto the DVD-RW / -R disc on which the number of recorded titles has reached the maximum (99). • Delete unnecessary original titles. (See page 55.) Recording Error You cannot record more than 999 chapters on one disc.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-79.html>PAGE 79</a></h6><p>Introduction Language Code Language Code Language Code Language Code Language Code Afar 4747 Frisian 5271 Macedonian 5957 Singhalese 6555 Afrikaans 4752 Galician 5358 Malagasy 5953 Siswat 6565 Albanian 6563 Georgian 5747 Malay 5965 Slovak 6557 Amharic 4759 German 5051 Malayalam 5958 Slovenian 6558 Arabic 4764 Greek 5158 Maltese 5966 Somali 6561 Armenian 5471 Greenlandic 5758 Maori 5955 Spanish 5165 Assamese 4765 Guarani 5360 Marathi 5964 Sundane</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-80.html>PAGE 80</a></h6><p>Specifications General VCR video heads Four heads Power requirements 220–240 V Power consumption 35 W Power consumption (standby) 0.5 W (When “Antenna Out” is set to “OFF”) Weight 5.0 kg ± 10 %, 50 Hz ± 0.5 % Dimensions (width x height x depth) 435 x 99.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-81.html>PAGE 81</a></h6><p></p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-82.html>PAGE 82</a></h6><p></p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-83.html>PAGE 83</a></h6><p></p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/funai/wd6d-m101/operation-manual-english/page-84.html>PAGE 84</a></h6><p>Declaration of Conformity This product complies with the requirement of the related directives. We: FUNAI ELECTRIC EUROPE Sp. z o.o. ul. Inżynierska 1, 67-100, Nowa Sól, Poland declare that the following product: DVD / Video Cassette recorder Model WD6D-M101 Trade Name: Funai is in compliance with the related regulations. Printed in P.R.C. E9TF8ED / E9TF8EH 1VMN33259 ★★★★★ Web Site: http://www.funai.eu © 2013 FUNAI ELECTRIC All rights reserved.</p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2025</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script>
googletag.cmd.push(function() { googletag.display('pixel'); });
</script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript>
$.extend({
redirectPost: function(location, args) {
var form = '';
$.each(args, function(key, value) {
form += '<input type="hidden" name="' + key + '" value="' + value + '">';
});
form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>';
$(document.body).append(form);
$("#s1").submit();
}
});
$(document).ready(function(){
$("#query").autocomplete({
minChars: 3,
groupBy: 'type',
paramName: 'q',
dataType: 'json',
serviceUrl: '/autocomplete',
noCache: true,
showNoSuggestionNotice: true,
noSuggestionNotice: 'Zarro results found',
onSelect: function (suggestion) {
$.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))});
}
});
var toc = $('.toc-selector');
if (toc.length) {
var slideParams = { duration: 800, easing: 'linear' };
toc.click(function() {
$(this).toggleClass('open');
var section = $('.toc-content');
var isCollapsed = section.attr('data-collapsed') === 'true';
if (isCollapsed) {
section.slideDown(slideParams)
section.attr('data-collapsed', 'false')
} else {
section.slideUp(slideParams);
section.attr('data-collapsed', 'true')
}
});
}
});
var lastSmall = $(window).width() < 576;
$(window).resize(function() {
var newSmall = $(window).width() < 576;
if (lastSmall != newSmall) {
lastSmall = newSmall;
window.location.href = window.location.href;
}
});
</script></body></html>
