Operating instructions
Table Of Contents
- Table of contents
- Description 1
- Safety notes 1
- Symbols 3
- Operation 4
- Making phone calls 4
- Making outside calls 4
- Specific trunk bundle selection 5
- Making internal calls 5
- Accepting calls 5
- Accepting calls (Pick-up) 5
- Defining your own number for the next call 6
- Switching call authorization for the next call 7
- Trunk group reservation 7
- Speed dialing from the telephone directory 7
- Voice announcement 7
- Switching a voice announcement for all numbers (day / night) 8
- Announcement 8
- Room monitoring 8
- Malicious call identification (Tracing) 9
- Allocating Project Numbers 9
- (keypad-function »Net fixed«) 10
- Sending a fax from a multi-function terminal 10
- Direct dial-in 10
- Inquiry call 10
- Call waiting 11
- Transferring calls with and without advance notice 12
- (Explicit call transfer) 13
- Broker’s call 13
- Three-party conference 13
- Call forwarding 14
- Silent signalling 14
- Call modes (Day- / Night) 15
- Teams 15
- Activating the switching function for an internal subscriber 16
- Follow me 16
- Block dialing (Austria) 17
- Hotel functions 18
- Wake-up call 18
- Door intercom device 19
- Modified code numbers 21
- Communication / Call charges 22
- Terminating an Internet connection from the phone 22
- System menu for the PABX 22
- System telephones 23
- Service 24
- Configuration using a telephone (administrators) 30
- Index
- A
- B
- C
- Call
- Call modes 15
- Call modes for teams 15
- Call rerouting 14
- Call switching in the network (ECT) 13
- Call waiting 11
- Charge counter 22
- Charge limit 22
- Charge limitation 22
- code numbers, modified 21
- Communication cost display 22
- Communication costs 22
- Communication data 22
- Completion of call (automatic)
- Conference 13
- Configuration 24
- Configuring wake-up call from »Reception desk phone« 18
- Configuring wake-up calls from the room phone 18
- D
- E
- F
- I
- K
- L
- M
- N
- O
- P
- R
- S
- Service 24,25
- Service access 24
- Service-Connection, incoming 25
- Service-Connection, outgoing 24
- Setting up call forwarding from an external location 16
- Signaling features 19
- Silent signalling 14,22
- Speaking alternatively with two parties 13
- Speaking simultaneously with two parties 13
- Specific trunk bundle selection 5
- Speed dialing from the telephone directory 7
- Switching all call modes 15
- Switching call authorization temporarily 7
- Symbols 3
- system menu 22
- System parked inquiry 11
- System telephones 23
- T
- Teams 15
- Telephone directory 7
- Temporarily suppressing transmission of your own number 7
- Terminating an Internet connection from the phone 22
- Three-party conference 13
- Tracing (Malicious call identification) 9
- Transfer a call 12
- Transferring a call 12
- Transferring the existing call using analog telephones 12
- Trunk group seizure 5
- U
- V
- W
Automatic completion of call to busy subscriber or on no answer
This function can only be used by telephones that permit suffix dialing. Automatic call completions from an inquiry
call are not possible.
Attention:
External Completions of call to busy subscriber are deleted after a period defined by the exchange.
Programming »Completion of call« for analog telephones
g *40 q a
Internal or external
subscriber is busy or
does not answer
Ack.
signal
Replace
handset
When the subscriber that was called hangs up his/her handset your telephone will ring.
When you lift up your handset the subscriber for which completion of call is active is called. If the party answers you
can conduct your call.
Programming »Completion of call on busy« for ISDN telephones
This feature is supported for ISDN telephones by the PABX at the internal ISDN connection. Please refer to the opera
-
ting instructions for your ISDN telephone for proper use.
Programming »Completion of call on no answer« for ISDN telephones
g *40 q a
Internal or external
subscriber does not
answer
Ack. signal, voice announcement or informati-
on on display
Replace
handset
When the subscriber that was called hangs up his/her handset your telephone will ring.
When you lift up your handset the subscriber for which completion of call is active is called. If the party answers you
can conduct your call.
Canceling automatic completion of call for analog telephones
Analog telephones use this procedure for canceling internal and external completions of call to busy subscriber and
no answer.
b #40 q a
Lift up handset Cancel completion of calls Ack. signal Replace handset
Deleting an automatic »Completion of Call on No Answer« with ISDN phones
Internal completion of calls on no reply is canceled with ISDN telephones using the following procedure.
b #40 q a
Lift up handset Cancel completion of calls Ack. signal Replace handset
Defining your own number for the next call
b#8ttt
Lift up handset Code Select external ISDN connection
(1...8)
(1= S2m)
Index
(0 … 9)
Dial call
number
Operation Defining your own number for the next call
6