Operating instructions
Table Of Contents
- Table of contents
- Description 1
- Safety notes 1
- Symbols 3
- Operation 4
- Making phone calls 4
- Making outside calls 4
- Specific trunk bundle selection 5
- Making internal calls 5
- Accepting calls 5
- Accepting calls (Pick-up) 5
- Defining your own number for the next call 6
- Switching call authorization for the next call 7
- Trunk group reservation 7
- Speed dialing from the telephone directory 7
- Voice announcement 7
- Switching a voice announcement for all numbers (day / night) 8
- Announcement 8
- Room monitoring 8
- Malicious call identification (Tracing) 9
- Allocating Project Numbers 9
- (keypad-function »Net fixed«) 10
- Sending a fax from a multi-function terminal 10
- Direct dial-in 10
- Inquiry call 10
- Call waiting 11
- Transferring calls with and without advance notice 12
- (Explicit call transfer) 13
- Broker’s call 13
- Three-party conference 13
- Call forwarding 14
- Silent signalling 14
- Call modes (Day- / Night) 15
- Teams 15
- Activating the switching function for an internal subscriber 16
- Follow me 16
- Block dialing (Austria) 17
- Hotel functions 18
- Wake-up call 18
- Door intercom device 19
- Modified code numbers 21
- Communication / Call charges 22
- Terminating an Internet connection from the phone 22
- System menu for the PABX 22
- System telephones 23
- Service 24
- Configuration using a telephone (administrators) 30
- Index
- A
- B
- C
- Call
- Call modes 15
- Call modes for teams 15
- Call rerouting 14
- Call switching in the network (ECT) 13
- Call waiting 11
- Charge counter 22
- Charge limit 22
- Charge limitation 22
- code numbers, modified 21
- Communication cost display 22
- Communication costs 22
- Communication data 22
- Completion of call (automatic)
- Conference 13
- Configuration 24
- Configuring wake-up call from »Reception desk phone« 18
- Configuring wake-up calls from the room phone 18
- D
- E
- F
- I
- K
- L
- M
- N
- O
- P
- R
- S
- Service 24,25
- Service access 24
- Service-Connection, incoming 25
- Service-Connection, outgoing 24
- Setting up call forwarding from an external location 16
- Signaling features 19
- Silent signalling 14,22
- Speaking alternatively with two parties 13
- Speaking simultaneously with two parties 13
- Specific trunk bundle selection 5
- Speed dialing from the telephone directory 7
- Switching all call modes 15
- Switching call authorization temporarily 7
- Symbols 3
- system menu 22
- System parked inquiry 11
- System telephones 23
- T
- Teams 15
- Telephone directory 7
- Temporarily suppressing transmission of your own number 7
- Terminating an Internet connection from the phone 22
- Three-party conference 13
- Tracing (Malicious call identification) 9
- Transfer a call 12
- Transferring a call 12
- Transferring the existing call using analog telephones 12
- Trunk group seizure 5
- U
- V
- W
Room monitoring from external telephones
You are located at an external telephone.
Lift up the handset of the phone from which you wish to conduct room monitoring and dial the external number to
which the service number for the PABX is assigned.
If remote access has been enabled and is possible at this time you will hear the special dial tone of your PABX.
Set your phone to frequency (DTMF) dialing, or use a DTMF manual transmitter.
tq t q
Enter PIN 2 Ack.
signal
Dial the number of the telephone
to be used for room monitoring
Ack.
signal
Room monitoring is activated
To end room monitoring, hang up the handset of the external telephone.
Malicious call identification (Tracing)
g *51 q a
Ongoing call, or caller
hangs up
Ack.
signal
Replace
handset
Attention:
Only hang up the handset after you have entered the code for tracing the caller and hear the positive acknowledge-
ment signal.
Allocating Project Numbers
Assigning a project number for a call you initiate
b *50 t # q t
Lift up handset Enter project number (
max. 6-place)
Ack.
signal
Dial call number
Project number for incoming external call to ISDN terminal device
You can use this feature at an ISDN terminal if your ISDN terminal device supports the function »Network Direct«
(keypad).
You are conducting a call and wish to register it for a project.
g *50 t # q g
Conversation Entering a project number
(max. 6 - place)
Ack.
signal
Continue call
Project number for an external call
You can use this feature at an analog or an ISDN terminal device if your ISDN terminal does not support the function
»Net direct« (Keypad) during an ongoing call.
You are conducting a call and wish to register it for a project.
g R *50 t # q R g
Conversation Entering a project number
(max. 6 - place)
Ack.
signal
Continue call
Malicious call identification (Tracing) Operation
9