Owner’s Manual SRM-80A / E – SIGNAL ROUTER/MONITOR SRM-80A SIGNAL ROUTER / MONITOR ROUTER / MONITOR SERIES
SRM-80A / E – SIGNAL ROUTER/MONITOR INTRODUCTION ABOUT THE SRM-80 Congratulations on your purchase of a Furman Model SRM-80A Signal Router/Monitor. Your SRM-80A will make monitoring, mixdown, and dubbing simpler and faster, thus helping you achieve professional results. SYSTEM SETUP 1 MO N ITOR LIN E OUTPU T A PO W ERE D SPEAKERS IN PU T The SRM-80A facilitates mixdown and dubbing between different media types without tying up additional console channels.
SRM-80A / E – SIGNAL ROUTER/MONITOR STEP-BY-STEP GUIDE TO SET-UP USING SINGLE POWER AMP ● Please also refer to the “System Set-Up #1” drawing on the facing page.
SRM-80A / E – SIGNAL ROUTER/MONITOR source select knobs labeled OUTPUT SELECT A through OUTPUT SELECT D. Monitoring any of these sources can be done using the MONITOR SELECT knob, highpower headphone amp and uniquely thoughtout speaker selection system that consists of three balanced line level speaker outputs A, B, and C. All of these outputs are compatible with powered monitors or passive speakers using a power amp.
SRM-80A / E – SIGNAL ROUTER/MONITOR The SRM-80A provides a high-resolution 40 LED x 2 bar graph meter to display the signal selected for listening. The meter displays a pre-fader signal for accurate monitoring of the signal going to tape or disc. This meter has true VU ballistics, or can be switched to Peak Program Mode via the front panel toggle switch. The meter also features a slow release-time Peak Hold function to allow easy verification of critical levels.
SRM-80A / E – SIGNAL ROUTER/MONITOR OPTIONAL SRM-RU REMOTE CONTROL ring the panel when tightening the screws, use nylon washers under the screw heads. The optional five-button SRM-RU allows remote control of Speaker Selection, MONO and DIM. An LED indicator is provided for each button and a 10 foot cable is included. SAFETY INFORMATION WARNING (For domestic units only): Do not remove the third prong on the SRM-80A’s AC plug.
SRM-80A / E – SIGNAL ROUTER/MONITOR DAT can receive signals from device “Source”, “B”, “C”, or “D” INPUTS depending on where you position this knob. OUTPUT SELECT B: This four-position knob works like the output select “A” knob described above. For example, if the “B” RCA OUTPUTS on the back panel are used for a cassette recorder, the recorder can receive signals from stereo device Source, “A”, “C”, or “D” INPUTS.
SRM-80A / E – SIGNAL ROUTER/MONITOR plug. Never use a three-prong to two-prong AC plug adapter to plug your SRM-80A into your wall socket. B/C position: Only the “A” and “B” monitor line outputs are used and the “B” amplifier’s speaker outputs are connected to the “FROM AMP (B) OUTPUT” binding posts. The B and C speaker outputs are combined to the SPEAKER B output jacks. This is to be used with a single power amp and 2 pairs of passive speakers via the binding posts on rear panel.
SRM-80A / E – SIGNAL ROUTER/MONITOR SPEAKERS B AND C Binding posts: For use with a single power amp. These left-right binding posts are provided for speaker pairs “B” and “C”. You may connect only passive speakers here. See figure B. NOTE: If you’d like to use a pair of powered speakers with your SRM-80A, do not connect them to the “B” or “C” binding posts. Set the AMP/SPK-B/C switch to the AMP- B/C position. Now you may use “A”, “B”, or “C” amplifier / speaker line outputs for powered speakers.
SRM-80A / E – SIGNAL ROUTER/MONITOR THREE YEAR LIMITED WARRANTY Furman Sound, Inc., having its principal place of business at 1997 South McDowell Blvd., Petaluma, CA 94954 (“Manufacturer”) warrants its SRM-80A (the “Product”) as follows: Manufacturer warrants to the original Purchaser of the Product that the Product sold hereunder will be free from defects in material and workmanship for a period of three years from the date of purchase.
SRM-80A / E – SIGNAL ROUTER/MONITOR facturer with respect to the Product. If any part of this Limited Warranty is determined to be void or illegal, the remainder shall remain in full force and effect. SERVICE Before returning any equipment for repair, please be sure that it is adequately packed and cushioned against damage in shipment, and that it is insured. We suggest that you save the original packaging and use it to ship the product for servicing.
SRM-80A / E – SIGNAL ROUTER/MONITOR SRM-80A SPECIFICATIONS OPERATING VOLTAGE 90 to 140 VAC ("E" version 180 to 280 VAC) LINE IN/OUT Input Impedances: Source A Input B Input C Input D Input Output Impedances: A Output To Power Amp B,C,D Output: Sensitivity for 0 VU: MONITOR OUTPUTS Noise: 56 ohms THD + N: 0.001% with 750mW driving a 150 ohm load.
