Owner's Manual

6
REAR PANEL FEATURES (continued)
Rear
Panel DIP
Switch
A rear
panel
three position
DIP switch is used to set
the sequence mode (+12V
ON,
+12V
OFF,
GND
ON,
Mom/ Maint) which defines how the M-8S will
react
to the
signal
presented on its REM input. The
table
below summarizes the behavior which is described
in
further
detail below.
Note that DIP
switch posi-
tion 2 overrides the setting
of
DIP
switch
1,
and
DIP
switch 3 overrides switches 1 and
2.
DIP
1
DIP2
DIP
3
MODE
Note:
The
front
panel
SEQUENCE
ON/OFF
switch
acts
as
an
override.
The
SEQUENCE
switch
must
be
1 2 3
12VON
GND
ON
MOM/MNT
in
the
ON
position
for
any
of
the
sequenced
outlets
to
be
activated.
~
·
~~
OFF
OFF
OFF
+12VOFF
Sequences
the
M-8S
ON
when
REM
=
Open
Circuit
···.
FACTORY
DEFAULT
SffiiNG
Sequences
.
the
M-8S
OFF
when
REM
=
12VOC
~~~
ON
OFF
OFF
+12V
ON
Sequences
the
M-8S
ON
when
REM
=
12VDC
Sequences
the
M-8S
OFF
when
REM
=
Open
Circuit
OFF
ON
OFF
GND
ON
~~~
Sequences
the
M-8S
ON
when
REM
is
connected
to
GND
terminal
~~~
ON
ON
OFF
GND
ON
Sequences
the
M-8S
OFF
when
REM
=
Open
Circuit
~~~
OFF
OFF
ON
Momentary
ON
OFF
ON
Momentary
~~~
Sequences
the
M-8S
from
ON
to
OFF
or
OFF
to
ON
each
time
+
12V
is
applied
to
the
REM
input.
~~~
OFF
ON
ON
Momentary
~~~
ON
ON
ON
Momentary
DIP
Switch
position
#1
(Factory default
is OFF)
DIP
Switch position 1 defines how the M-8S
will
behave when +12VDC is
applied
to the REM pin
on the Remote interface.
If
this switch is
in
the
ON
position, the M-8S
will
sequence
ON
when +12V
is
applied
to the REM input. If this switch
is
in
the
OFF position (+12V OFF) the M-8S
will
sequence
OFF
when +12V is
applied
to the REM input. DIP
switches 2 and 3 must be
in
the
OFF
position (Main-
tained mode).
DIP
Switch
position
#2
(Factory default
is
OFF)
DIP Switch position 2 defines how the M-8S
will
behave
when
GND is
applied
to the REM pin on the
Remote interface.
If this switch is
in
the
ON
position,
the M-8S will
sequence ON
when GND
is
applied
to
the REM input.
If
this switch
is
in
the
OFF
position
the M-8S will follow
the behavior defined by
DIP
Switch #1.
DIP switch 3 must be
in
the
OFF
position
(Maintained mode).
DIP
Switch
position
#3
(Factory
default
is OFF)
DIP Switch position 3 defines the switching prefer-
ence for switches or devices connected to the REM
pin on the Remote Interface. If
this switch is
in
the
ON
position, the M-8S
will
operate
in
Momentary
mode.
If this switch
is
in
the
OFF
position the M-8S
will
operate
in
Maintained mode.
Maintained switches,
for example toggle
switches
or push-ON
I
push-OFF push button
latching
switches maintain their contact position until
the
switch is actuated a second time. Thus a switch that
is
closed will
remain
closed until
the switch position
is changed (such as the Furman
RS-1
).