Data Sheet

REAR LAMP
SWITCH
DELAY OUTLET BANKS
1, 2 and 3 INDICATORS
EXTREME VOLTAGE
INDICATOR
SEQUENCING
ENABLING SWITCH
POWER ON
INDICATOR
PROTECTION OK
INDICATOR
SWITCHED
OUTLET
POWER
SWITCH
AC POWER CORD DETACHABLE
2.5 M LENGTH IEC-C13
AC INLET IEC-C14 MALE
WITH METAL RETAINER CLIP
SWITCHED
OUTLETS BANK
POWER
LED
DELAY 2 OUTLETS
BANK SEQUENCED
DELAY TIME
ADJUSTMENT
DELAY 3 OUTLETS
BANK SEQUENCED
DELAY 1 OUTLETS
BANK SEQUENCED
PHOENIX-TYPE REMOVABLE
4 PIN CONNECTOR
3 POSITION
DIP SWITCH
LAMP
CONNECTOR
RESETABLE 10 AMP
CIRCUIT BREAKER
CEE-7/7
Schuko Plug
FRONT PANEL FEATURES
REAR PANEL FEATURES
Featuring SMP, LiFT, and EVS Technologies
Furman 1800 S. McDowell Blvd., Petaluma, CA 94954
©2014 Core Brands. All rights reserved. Furman is registered trademark of Core Brands a Nortek Company
www.furmansound.com
Specifications subject to change due to product upgrades and improvements.
Maximum AC Current Rating:
• 10 Amps, 220 - 240 VAC @ 50 – 60 Hz
(Thermal breaker)
AC Cord:
• 1 mm2 x 3, 2.5 m length, IEC-C13 (Female) to
CEE-7/7 Schuko plug.
AC Inlet:
• IEC-C14 (Male) with metal wire retainer clip
AC Outlets:
• Convenience Outlet (Front Panel) 1 Switched IEC C-13
• Rear Panel Outlets: 2 Switched IEC C-13 (1 duplex),
• 6 Sequenced IEC C-13 (3 duplexes each controlled by separate relay)
AC Surge Protection:
• Spike Protection Mode: Line to neutral, zero ground leakage
• Spike Clamping Voltage: 376VAC peak @ 6,000 Volts/3,000 Amps
• Response Time: 1 nanosecond
• Maximum Surge Current: 6,500 Amps
• AC Over-voltage Protection: EVS, 275VAC+/-5VAC
• AC Over-voltage Reset Modes: Auto
• Series Multi-Stage Protection
AC Filtering:
• LiFT
• Noise Attenuation: 10dB @10KHz, 40dB@100KHz,
50dB@500KH
SPECIFICATIONS
SERIES III
PS-8RE III
Model PRodUCT diMensions WeighT CARTon diMensions WeighT single UniT UPC MAsTeR PACk QTy MAsTeR PACk UPC
PS-8RE III 7”D x 19”W x 1.75”H 7 lbs 12”D x 22”W x 3.5”H 8.5 lbs 654061041085 6 50654061041080
WEIGHTS, DIMENSIONS AND UPC CODES
2-28-14
Delay Adjustment
The delay interval, which is the time between the turn-on / turn-off
of consecutive delay outlets 1 and 2, or 2 and 3, is factory preset
to approximately 5 seconds. It is possible to lengthen or shorten
the delay interval by changing the position of the DLY-ADJ trim pot
located on the right side of rear panel.
Remote Interface
The PS-8RE III has a remote interface which can be used to control
the PS-8RE III remotely using a Furman RS-1 (Maintained) or RS-2
(Momentary) wall switches (sold separately).
Dip Switches
A rear panel three position DIP switch is used to set the sequence mode
(+12V ON, +12V OFF, GND ON, Mom/ Maint) which defines how the PS-8RE
III will react to the signal presented on its REM input.
Rear Lamp Socket
The PS-8RE III features a rear rack BNC socket which will accept any
12 VDC or 12VAC up to ½ Amp gooseneck lamp assembly, (such as
the Furman GN-LED or GN-I).