MODEL # YNJ-19702C24 YNJ-19702C35 Questions? GIVE US A CALL: 1-888-980-5122 MON－FRI 8:30AM－5:30PM (PST) TOOLS REQUIRED Phillips Screwdriver (Not Included) Hammer (Not Included) 2 - People Recommended ASSEMBLY RATING EASY DIFFICULT The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
/ 19
/ 19
ASSEMBLY CARE ADVICE FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Turn clockwise to tighten and only tighten when step is completed or when instructed to do so. Position each part correctly and insert screws or bolts into their respective holes. Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.
/ 19
BUFFET YNJ-19702C24&C35 A R I H C J D PARTS A 1PC B 1PC F 1PC L 2PCS R 2PCS G 2PCS M 2PCS S 2PCS H 2PCS N 2PCS T 2PCS I 1PC O 1PC U 2PCS P 2PCS V 2PCS Q 1PC W 1PC C 1PC D 1PC J 1PC E 1PC K 2PCS ACCESSORIES HARDWARE 1 25PCS 2 25PCS 3 21PCS 4 20PCS 1.25" 7 8PCS 8 2PCS 9 4PCS 10 2PCS 14 16PCS 15 4PCS 0.59" 1.97" 11 2PCS A1 4PCS 0.59" 12 4PCS 0.39" 0.67" 13 4PCS 5 12PCS 6 4PCS 16 4PCS 6 / 19 A3 5PCS 0.87" A4 1PC A5 1PC A7 1PC A8 1SET 0.59" 0.71" 0.
GET READY Please group boards as below.
1 1 Hardware 1 x18PCS Hardware 3 x4PCS 1 1 Accessory A5 x1PC 1 1 1 A 1 1 1 1 1 1 1 1 B 1 3 A5 3 OPTIONAL 3 Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
2 3 Hardware 1 x3PCS Hardware 3 x6PCS 3 Accessory A5 x1PC 1 D 3 3 1 E 3 A5 OPTIONAL Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
3 3 Hardware 3 x6PCS Hardware 8 x2PCS Hardware 9 x4PCS Hardware 10 x2PCS Hardware 11 x2PCS Hardware 13 x4PCS Hardware 14 x8PCS X2 A5 K OPTIONAL 3 Apply a dab of glue into dowel holes of panels before inserting dowels (#3). 3 Accessory A1 x2PCS Accessory A2 x2PCS Accessory A5 x1PC X2 9 9 G 8 3 Attach magnet to panel (#G) by using screws (#9).Make sure magnet (#8) is facing the direction of the arrow. 13 14 14 A2 J HOLE USAGE Align screws with the darkened holes in the above diagram.
4 Q S Hardware 1 x4PCS Hardware 3 x5PCS X2 3 Accessory A5 x1PC 3 3 1 A5 1 T R OPTIONAL X2 X2 Apply a dab of glue into dowel holes of panels before inserting dowels (#3). 3 5 Part E Part F Part H Part M Front Top x1PC x1PC x2PCS x2PCS 4 Finished Side 4 4 5 Hardware 4 x6PCS Hardware 5 x8PCS 5 M 5 Accessory A4 x1PC M H 4 F H 4 or 5 4 A4 RECOMMEND Recommend using a power tool to only tighten hardware (#5) faster.
6 Part D x1PC Part Q x1PC or Hardware 2 x1PC Hardware 5 x4PCS A4 Accessory A4 x1PC RECOMMEND Recommend using a power tool to only tighten hardware (#5) faster. Accessory (#A4) could also work for hardware (#5) if a power tool is not present. Front Rotate Top 90° E 5 F D 5 5 Q 2 5 1 2 Please refer to page 5 for detailed instructions on how to fasten cam locks (#2) to cam bolts (#1).
7 Part B x1PC Part C x1PC Part G x2PCS 1 Front Top Hardware 2 x8PCS 2 Accessory A3 x5PCS G 2 C 2 2 G A3 2 2 2 D B 2 A3 2 A3 13 / 19 A3 A3
8 Part A Part K Part L Part W x1PC x2PCS x2PCS x1PC 2 K K 2 2 Hardware 2 x12PCS Hardware 4 x6PCS 2 4 4 A 4 4 4 4 L L Front Top A 2 2 1 W 2 2 2 2 2 F 2 C 2 Top B E Front 14 / 19
9 Part O x1PC Part P x2PCS Top P P Front O 10 Part N x2PCS Hardware 7 x8PCS N Top 7 N O Front Insert shelf pins (#7) to the holes of the desired shelf height.
11 Part I x1PC Part J x1PC 14 14 Hardware 14 x8PCS J HOLE USAGE Align screws with the darkened holes in the above diagram. HINGE ADJUSTMENT I Depth Adjustment. Length Adjustment.
13 6 Hardware 6 x4PCS 6 6 R Fully extend drawer rails then align the rails smallest hole to the drawer slide panels holes. Secure with bolts (#6). R Top Front 14 Hardware 12 x4PCS Hardware 15 x4PCS Hardware 16 x4PCS Top 15 Front 16 W 12 12 Insert fixative plates (#15) through the thin lined gaps between back and side panels, then secure by using screws (#16).
15 Accessory A6 x1PC Accessory A7 x1PC Accessory A8 x1SET A7 A A6 A8 For safety, please secure unit onto wall by using wall mounted straps provided. Refer to page 19 on wall mounting guide. 16 ASSEMBLY COMPLETED Please ensure the furniture rests on an even and flat surface. If the produst wobbles or feels loose,double-check all bolts and/or screws are properly tightened and secured. Keep this handy! Please retain this instruction manual and any order-related information for future reference.
/ 19
