000W Pure Sine Wave Power Inverter Onduleur sinusoïdal 1000W Instruction Manual / Manuel d’instructions Model / Modèle: FIVBDP10A
English Welcome Thank you and congratulations for purchasing this Furrion® 1000W Pure Sine Wave Power Inverter. Before operating your new product, please read these instructions carefully. This instruction manual contains information for safe use, installation and maintenance of the product. Please keep this instruction manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury. Be sure to pass on this manual to new owners of this product.
Contents English Welcome.............................................................................................1 Contents.............................................................................................2 Important Safety Instructions.............................................................3 General Safety Precautions.....................................................................................3 Precautions When Working with Batteries............................................
Important Safety Instructions English WARNING ●● Before using the Inverter, read and save the safety instructions. IMPORTANT: THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCTION LABELS, PLUS YOUR VEHICLE’S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE.
About your Product How your Inverter Works ●● 1000 Watt continuous output for electronic appliances ●● High surge power up to 2500W ●● Pure sine wave output to operate higherend electronic equipment ●● Built in transfer switch with less than 20ms transfer time.
Product Overview English Front Panel LED Indicator Circuit Breaker On/Off Switch Strain Relief Door of AC Wire Compartment AC Power Supply Cord with 5-15P Plug Rear Panel Battery Negative Terminal Battery Positive Terminal Chassis Ground 5 Remote Control Port Furrion Communication RJ25(6P6C) Port
Installation What’s in the Box Mounting the Inverter The inverter has four slots in its mounting bracket that allows the unit to be fastened against a bulkhead, floor, wall or other flat surface. (Fig. 1) Fig. 1 The inverter can be operated in any position, however, if it is to be mounted on a wall, mount it horizontally (see Fig. 2 for correct mounting direction) so that indicators, switches, outlets and terminal blocks located on the front panel are visible and accessible.
Installation English Connecting to a Load WARNING SHOCK HAZARD! Before proceeding further, carefully check that the Inverter is NOT connected to any batteries, and that all wiring is disconnected from any electrical sources. Make sure the bypass AC input plug is disconnected to any AC source. Do not connect the output terminals of the Inverter to an incoming AC source. Make sure the power switch is in off position before and after the installation.
Installation 6. Replace the wire clip and fix with 2 screws provided. (Fig. 7) English 3. Connect the AC output wiring to the inverter AC output hard-wire (pigtails leads) by using wire connectors. Black to black, white to white. (Fig. 5) Fig. 7 Fig. 5 AC Output Wiring Line (L) Black Neutral (N) White Ground Green or Bare copper Wire Length/ Gauge 7. Using a 5/32” hex wrench, loosen the ground lug screw located on the mid left side of the rear panel.
Installation English Connecting to a Power Source CAUTION ●● The power inverter must be connected only to batteries with a nominal output voltage of 12volts. The unit will not operate from a 6 volt battery, and will sustain permanent damage if connected to a 24 volt battery. ●● The input current of this inverter is about 100A with full load, make sure the battery could discharge over 100A continuously. ●● The battery should have a Cold Cranking Amp more than 500A.
Operation English To operate the inverter, turn it on by pressing the ON/OFF switch. The inverter is now ready to deliver AC power to your loads. If you are loading several appliances, turn them on separately after the inverter switch is on, this process is to avoid the power inverter from delivering the starting current all at once to the loads. The inverter can operate with and without being connected to a nominal 12V DC battery source by using the bypass AC input mode.
English Care and Maintenance Clean only with dry cloth. Do not clean the unit with strong chemical agents or abrasive cleaners. Never spill liquid of any kind on the product. Do not allow residue or liquids to enter any part of the appliance as this may cause risk of electrocution. Always disconnect from any power source before cleaning. Fuse Replacement CAUTION: NO USER-SERVICEABLE COMPONENTS INSIDE. DO NOT ATTEMPT TO OPEN THE INVERTER.
Specifications Specifications 10.
Troubleshooting English TROUBLE/SYMPTOM SOLUTION Low battery voltage Recharge or replace battery Over battery voltage Check the battery voltage Output short circuit protection Check the output, remove the short circuit and restart the inverter by turning the switch off/on Inverter shut down by overload Remove or reduce load, restart the inverter by turning the switch off/on Inverter overheat thermal shutdown Remove or reduce load, wait for inverter to cool No AC output (Red & Green LED not lit)
Warranty Furrion warrants for a period of 1 year from date of retail purchase by the original end-use English purchaser, that this product, when delivered to you in new condition, in original packaging, from a Furrion authorized reseller and used in normal conditions, is free from any defects in manufacturing, materials, and workmanship. In case of such defect, Furrion shall replace or repair the product at no charge to you.
Warranty English FURRION IS NOT RESPONSIBLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF ANY EQUIPMENT OR PROPERTY, ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH FURRION PRODUCTS.
1. Furrion Innovation Center & Institute of Technology ● 52567 Independence Ct., Elkhart, IN 46514, USA ● Toll free:1-888-354-5792 ● Email: support@furrion.com ©2007-2018 Furrion Ltd. Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. ©2007-2018 Furrion Ltd. Furrion® et le logo Furrion sont des marques déposées par Furrion Ltd. et enregistrées aux Etats-Unis et ailleurs. FURRION.COM IM-FEN00001 V6.
1000W DECK MOUNT INVERTER FIVBDP10A UP TO 1000W HIGH SURGE POWER CONTINUOUS OUTPUT 2500W COMPATIBLE WITH APPLIANCES UNDER 1000W • Low standby current • Built in advance microprocessor for friendly user interface HIGH QUALITY PURE SINE WAVE LED INDICATOR WITH ALL OPERATIONS STATUS EASY INSTALLATION • Hardwire AC connection • Built in transfer switch with a transfer time of less than 20 milliseconds
1000W DECK MOUNT INVERTER 21⁄8”(53mm) 71⁄2”(190mm) 163⁄4”(425mm) | 1115⁄16”(303mm) 1411⁄16”(372mm) FIVBDP10A 21⁄16”(52mm) 83⁄4”(222mm) 47⁄16”(112mm) 95⁄16”(236mm) Packaging Information Specifications Battery Voltage AC Bypass Input Output Voltage Output Frequency Output Waveform Continuous Rated Power Surge Output Power (2 Seconds) Maximum Peak Efficiency Circuit Breaker Bypass Transfer Time Transfer Relay Rating Low Battery Protection Over Voltage Protection Over Load Protection Over Temperatur
_..URRION WARRANTY CARD/ CERTIFICAT DE GARANTIE TARJETA DE GARANTfA / GARANTIEKARTE CART.
WARRANTY CARD Congratulations on purchasing your new Fumon product. All Furrion products are made to strict quality standards. If used properly for its intended purpose, your product should provide many years of use. We are pleased to provide you with a 1 year warranty on your Furrion product. The details of this warranty are set out in the terms and conditions (see reverse) which supplement the authorised dealer's Terms and Conditions of Sale.
EN 6. Following the filing of a claim, Furrion will investigate the claim. If we believe there 1s a defect covered by the warranty, we will at our option either repair or replace the defective product !or part). 7. Please note in the event that no defect can be found, it is your responsibility to pay for the re-delivery of the replacement items. If a defect is found, Furrion will pay for the re-delivery of the replacement items. 8.
www.furrion.
