COLOR VIDEO PLOTTER GD-1700C COLOR VIDEO PLOTTER GD-1710C VIDEO PLOTTER GD-1700
Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : 0798-65-2111 fax 0798-65-4200 : All rights reserved. Printed in Japan FIRST EDITION : APR. 2001 H PUB.No. OME-44090 ( HIMA ) GD-1700/1700C/1710C : APR.
SAFETY INSTRUCTIONS WARNING CAUTION ELECTRICAL SHOCK HAZARD No one navigation device should ever be solely replied upon for the navigation of a vessel. Do not open the equipment. Only qualified personnel should work inside the equipment. Always confirm position against all available aids to navigation, for safety of vessel and crew. Do not disassemble or modify the equipment. A warning label is attached to the equipment. Do not remove the label.
TABLE OF CONTENTS FOREWORD ............................................................................................................... viii SYSTEM CONFIGURATIONS........................................................................................ x WHAT IS WAAS? ......................................................................................................... xii 1. OPERATIONAL OVERVIEW..................................................................................1-1 1.
TM 2.5.3 FURUNO and NavCharts 2.5.4 C-MAP charts ...............................................................................................................2-14 charts ...............................................................................2-12 2.6 Working with Track ....................................................................................................................2-18 2.6.1 Displaying track ..................................................................................
3.5 Reducing Sea Clutter ..................................................................................................................3-4 3.5.1 How the A/C SEA works .................................................................................................3-4 3.5.2 Adjusting A/C SEA ..........................................................................................................3-4 3.6 Reducing Precipitation Clutter....................................................................
3.22 Guard Alarm ..............................................................................................................................3-30 3.22.1 Setting a guard alarm zone ..........................................................................................3-30 3.22.2 When the alarm is violated… .......................................................................................3-31 3.22.3 Cancelling the guard alarm ..........................................................................
4.11 Display Colors (GD-1700C/1710C) ...........................................................................................4-18 4.12 Alarms .......................................................................................................................................4-19 4.12.1 Audio alarm on/off.........................................................................................................4-19 4.12.2 Bottom alarm ........................................................................
6.3 Loading Waypoint Data from Yeoman..................................................................................... 6-8 6.4 Receiving Data Via Network Equipment.................................................................................. 6-9 6.5 Outputting Data Through the Network................................................................................... 6-10 7. MAINTENANCE, TROUBLESHOOTING............................................................... 7-1 7.1 7.2 7.3 7.4 7.5 7.6 7.
FOREWORD A Word to the Owner of the GD-1700/1710 Series Video Plotter FURUNO Electric Company thanks you for purchasing the GD-1700/1710 Series Video Plotter. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers.
Features The 1700 series work within our new product-network system called the “NavNet.” Each product has an IP address to communicate with NavNet compatible products within the network, using TCP/IP protocol through an Ethernet 10BASE-T network. The main features are as follows: • Three models are available: GD-1700: Monochrome LCD GD-1700C: Color LCD GD-1710C: High-precision color LCD • Bright 7” screen visible even under direct sunlight.
SYSTEM CONFIGURATIONS All NavNet products incorporate a “network circuit board” to integrate each NavNet product on board through an optional LAN cable (Ethernet 10BASE-T). Each NavNet product is assigned an IP address to enable transfer of images between other NavNet products. For example, video plotter pictures can be transferred to a radar and vice versa. Pictures received via the NavNet may be adjusted at the receiving end.
Two-unit NavNet system Radar Antenna Unit GPS Receiver GP-310B/320B PLOTTER Radar data Plotter data Two-unit NavNet system Three-or-more-unit NavNet system (Max. 4 NavNet capable display units) GP-310B/320B Antenna Unit Radar data Plotter data HUB Sounder data Note: The picture disappears 10 seconds after the NavNet cable is disconnected from a "sub" NavNet display unit.
WHAT IS WAAS? WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based Augmentation System) navigation system. SBAS provides GPS signal corrections to SBAS users, for even better position accuracy, typically better than three meters. Two more SBAS providers are also currently under development, MSAS (Multi-Functional Satellite Augmentation System) for Japan and EGNOS (Euro Geostationary Navigation Overlay Service) for Europe.
1. OPERATIONAL OVERVIEW This chapter provides basic information needed to get you started using your plotter.
1. OPERATIONAL OVERVIEW 1.1 Operating Controls 1.1.1 Display unit controls Overview of display unit controls The plotter, radar, sounder and chart systems are mainly operated with controls of the display unit (and remote controller). Ten keys are labeled and they provide the function shown on their labels. The five soft keys provide various functions according to current operating mode. The [ENTER] knob mainly functions to register selections on the menu and enter alphanumeric data.
1. OPERATIONAL OVERVIEW Soft keys The function of the five soft keys changes according to the operation. Their labels for their current functions are shown on the screen to the left of the keys. To hide or show the soft key labels, press the [HIDE/SHOW] key. Each press of the key shows preset soft keys, user function keys or turns off navigation information (at the top of the screen). SOFT KEYS Display unit Some soft keys show the current state of the soft key function in reverse video as shown below.
1. OPERATIONAL OVERVIEW [ENTER] knob The [ENTER] knob functions to • Register data • Enter alphanumeric data such as waypoint name • Select menu items and options • Adjust setting For data input, clockwise rotation of the knob selects an alphabet, symbol or numeric, in one of the sequences shown below. After you have selected desired alphanumeric character push the [ENTER] knob to register your selection.
1. OPERATIONAL OVERVIEW 1.1.2 Remote controller SAVE RANGE MOB DISP ABC 1 DEF 2 GHI 3 JKL 4 MNO 5 PQR 6 STU 7 VWX 8 YZ& 9 ’# 0 EBL/VRM WPT Operating distance 90°: Up to 5 m ±45°: Up to 3 m Replace the batteries (AA) when the distance from which the display unit can be operated shortens. Note: The remote controller may become damaged if dropped. Mishandling of the remote controller is not covered by the warranty.
1. OPERATIONAL OVERVIEW 1.2 Inserting a Chart Card Your unit reads FURUNO and NavCharts™ (NAVIONICS) chart cards, or C-MAP chart cards, depending on the type of display unit you have. Insert the appropriate chart card for your area as follows: 1. Open the chart card slot lid. Chart slot Display unit Card drive Memory card interface unit (option) 2. Insert desired chart card groove side up. 3. Close the lid to protect the chart drive. Note 1: Do not remove a card while the chart is being drawn.
1. OPERATIONAL OVERVIEW 1.3 Turning the Unit On/Off Press the [POWER/BRILL] key to turn the unit on. A beep sounds and the equipment proceeds in the sequence shown below, displaying the production information screen, startup test results and the chart usage disclaimer. The startup test checks the ROM, RAM, internal battery and backup data for proper operation, displaying the results for each as OK or NG (No Good). If NG appears an appropriate message appears on the screen.
1. OPERATIONAL OVERVIEW 1.4 Display Brilliance, Panel Brilliance, Contrast, Hue You can adjust display brilliance, panel brilliance, contrast and hue (GD-1700C/1710C only) as shown below. 1.4.1 Display brilliance, panel brilliance 1. Press the [POWER/BRILL] key momentarily. A set of soft keys for adjustment of brilliance, contrast and hue (GD-1700C/1710C only) appear. Current selection is highlighted. 34° 22. 3456'N 080° 22. 3456'E BRILL TRIP N 99.9 nm CONTST 359.9°M 19.9 kt DISPLY BRILL 16.
1. OPERATIONAL OVERVIEW 1.4.2 Contrast 1. Press the [POWER/BRILL] key momentarily. 2. Press the CONTST (GD-1700) or CONTST/HUE (GD-1700C/1710C) soft key. 3. For the GD-1700C/1710C, two soft keys appear at the pressing of the CONTST/HUE soft key: CONTST and HUE. Press the CONTST soft key to adjust the contrast. CONTRAST 8 Contrast window 4. Adjust the [ENTER] knob, clockwise to raise the setting or counterclockwise to decrease it. You may also use the CONTST soft key.
1. OPERATIONAL OVERVIEW 1.5 Selecting a Display 1.5.1 Display modes If you have a network radar, navigator and network sounder connected, four full-screen displays are available: plotter, radar, video sounder and navigation data. (The GD-1700C/1710C has five screens, those mentioned above plus the overlay screen.) In addition to the full-screen display, you can divide the screen into half-screen combination displays to show two sets of images (data). Full screen (Ex. plotter) Combination screen (Ex.
1. OPERATIONAL OVERVIEW 1.5.2 Selecting a display 1. Press the [DISP] key to show the full-screen selection window. The icons of modes not available are marked with an “X.”. PAGE1-PAGE5 are user-arrangeable displays called “hot pages,” which you can configure as you like. For further details, see the paragraph “5.5 Hot Page Setup.” RADAR PLOT SNDR NAV OVRLY* Basic display screens * = Color model only Hot pages PAGE1 PAGE2 PAGE3 PAGE4 PAGE5 · TURN KNOB TO SELECT MODE AND PUSH KNOB TO ENTER.
1. OPERATIONAL OVERVIEW 1.5.3 Switching control in combination and overlay screens A soft key is provided in relevant combination and overlay screens (GD-1700C/1710C only) to switch control between displays. In the example below, the RADAR CNTRL and PLOTTR CNTRL soft keys enable switching control between the radar and plotter screens in the plotter/radar combination display. 34° 22. 3456'N 080° 22. 3456'E 34° 22. 3456'N 080° 22. 3456'E 359.9°M TRIP NU 19.9 kt 99.9 nm 16.0nm 16.0nm SIGNAL PROC.
1. OPERATIONAL OVERVIEW 1.5.4 Selecting image source When more than one network radar or network sounder is connected to the equipment, you may select an image source for each as shown below. This is not necessary when only one network radar or network sounder is connected. 1. Press the [DISP] key. 2. Press any soft key to show the following display. ▲ SELECT SOURCE RADAR SOURCE RADAR - - SOUNDER SOURCE SOUNDER IP ADDRESS 172. 031. 014.
1. OPERATIONAL OVERVIEW 1.6 Cursor Pad, Cursor The cursor pad functions to shift the cursor, for measurement of latitude and longitude position and range and bearing to a location. Press the cursor pad to turn the cursor on, and the cursor appears at the own ship’s position. Operate the cursor pad to shift the cursor. The cursor moves in the direction of the arrow or diagonal pressed on the cursor pad.
1. OPERATIONAL OVERVIEW 1.7 Entering the MOB Mark, Setting MOB as Destination The MOB (Man Overboard) mark functions to mark man overboard position. You can inscribe this mark from any mode, except while playing back data or conducting any test. Note that this function requires position data. MOB mark M (MOB) Range, bearing Current position Man overboad M 162.5°M O B 0.49 nm MOB Data Box Bearing and range to MOB position MOB concept 1.
1. OPERATIONAL OVERVIEW 1.8 Data Boxes Data boxes, providing navigation data, may be shown on any full-screen display. Up to six data boxes (two in case of large characters) may be shown, and the default data boxes are position (in latitude and longitude), course over ground, speed over ground and trip log. The user may choose which data to display, where to locate it, and show or hide it as desired. In addition, data boxes may be set independently for each display mode (plotter, radar, sounder).
1. OPERATIONAL OVERVIEW 1.9 Function Keys The function keys provide for one-touch execution of a desired function. The default function key settings are as shown in the table below. Function Key #1 #2 #3 #4 #5 1.9.
1. OPERATIONAL OVERVIEW 1.10 Simulation Display The simulation display, which is for use by service technicians for demonstration purposes, provides simulated operation to help acquaint you with the many features your unit has to offer. It allows you to view and control a simulated plotter, radar and sounder picture, without position-fixing equipment, network radar or a network sounder. Most controls are operative, thus you may practice setting destination, enter waypoints, etc.
1. OPERATIONAL OVERVIEW Plotter 1. Select PLOTTER, then press the EDIT soft key. PLOTTER ▲ ¡ SIMULATION ¤ LIVE ▼ 2. Select SIMULATION, then press the [ENTER] knob. 3. Select SPEED, then press the EDIT soft key. 4. Enter speed (setting range, 0-99 kt, default speed, 0 kt) with the alphanumeric keys, then push the [ENTER] knob. 5. Select COURSE, then press the EDIT key. 6. Select “8 FIGURE” to trace the simulated ship’s track in a figure-eight course, or enter your own course at DIRECTION.
1. OPERATIONAL OVERVIEW Sounder 1. Select SOUNDER, then press the EDIT soft key. SOUNDER ▲ ¡ SIMULATION 1 ¡ SIMULATION 2 ¤ LIVE ▼ 2. Select SIMULATION 1 (internally generated echoes) or SIMULATION 2 (network sounder-generated echoes), then press the [ENTER] knob. Note 1: If the network sounder could not be found “Sounder source is not found. Cannot get simulation data.” appears. And if the sounder is not active, the message “Sounder is not active. Cannot get simulation data.” is displayed.
2. PLOTTER OPERATION 2.1 Plotter Displays You may show the plotter display over the entire screen, in the overlay screen (GD-1700C/1710C), or in a combination screen. 2.1.1 Full-screen plotter display Nav data window (Data changes with NAV soft key setting and cursor status. For details see next page.) 34° 22. 3456'N 080° 22. 3456'E Scale M TRIP NU 99.9 nm MARK ENTRY 16.
2. PLOTTER OPERATION Nav data window The data shown in the nav data window depends on the status of the NAV soft key and the cursor. Presentation Mode Latitude and longitude of cursor intersection Latitude, Longitude Bearing to Cursor 34°24. 3456'N + 124°24. 3456'W 359. 9°M 59.9nm Cursor Mark NU TRIP 99.
2. PLOTTER OPERATION 2.1.2 Compass display The compass display, shown in combination displays, provides steering information. The compass rose shows two triangles: the black triangle (hollow on monochrome model) shows the bearing to destination waypoint and the red (solid on the monochrome model) triangle, which moves with ship’s course, shows own ship’s course. The water temperature and depth graphs, which require appropriate sensors, show the latest 10 minutes of water temperature and depth data.
2. PLOTTER OPERATION Reading the XTE (cross-track error) monitor The XTE monitor, located below the compass rose, shows the distance you are off course and the direction to steer to return to course. The own ship marker moves according to direction and distance off course. It is shown in black when the amount of cross-track error is within the XTE monitor range and yellow when it is over. (On the monochrome model it flashes when the amount of cross-track error is more than the XTE monitor range.
2. PLOTTER OPERATION 2.1.3 Highway display The highway display, shown in combination displays, provides a graphic presentation of ship’s track along intended course. It is useful for monitoring ship’s progress toward a waypoint. The own ship marker shows relation between ship and intended course. The XTE monitor shows the direction and amount your vessel is off course – the arrow shows the direction to steer to return to your course and the numeric the distance you are off course.
2. PLOTTER OPERATION 2.1.4 Nav data display The nav data display provides comprehensive navigation data, and it can be shown in a two-screen combination display. The user may select what data to display and where to display it. For details see the paragraph “5.7 Nav Data Display Setup.” Appropriate sensors are required. Bars ( - -) appear when corresponding sensor is not connected. Position TRIP LOG POSITION 34° 34. 5678' N 120° 34. 5678' W WPT POSITION 34° 14. 5678' N 120° 14.
2. PLOTTER OPERATION 2.2 Presentation Mode Three types of presentation modes are provided for the plotter display: north-up, course-up and auto course-up. To change the presentation mode, first press the [HIDE/SHOW] key if the plotter soft keys are not displayed. Press the MODE soft key to select desired mode. Each press of the key changes the presentation mode and presentation mode indication (top right-hand corner of the screen) cyclically in the sequence of North-up, Course-up and Auto course-up. 2.2.
2. PLOTTER OPERATION 2.2.2 Course-up The course-up mode is useful for monitoring ship’s progress towards a waypoint. The destination is at the top of the screen when a destination is set. When no destination is set, the course or heading is at the top of the screen at the moment the course-up mode is selected. A filled triangle marks own ship’s position.
2. PLOTTER OPERATION 2.3 Shifting the Display The plotter display can be shifted as below. 1. Press the cursor pad to display the cursor. 2. Locate the cursor at a screen edge and press and hold down the cursor pad. The screen shifts in the direction opposite of cursor location. 3. To turn off the cursor, press the CENTER soft key. This also returns the own ship marker to the screen center. 2.4 Chart Scale Chart scale (range) may be selected with the [RANGE -] or [RANGE +] key.
2. PLOTTER OPERATION 2.5 Chart Cards 2.5.1 Chart card overview Your unit reads FURUNO and NavCharts™ (NAVIONICS) charts, or C-MAP charts, depending on the type of display unit you have. When you insert a suitable chart card in the slot and your boat is near any cartographic object, a chart appears. If a wrong card is inserted or a wrong chart scale is selected, landmasses will appear hollow. Chart icons appear at the top of the display to help you select a suitable chart scale.
2. PLOTTER OPERATION 2.5.2 Indices and chart enlargement When the [RANGE] key is operated, you will see several frames appear on the chart. These frames are called indices and they show you what parts of the chart can be enlarged in the current range. Sample chart (Japan) showing indices When a chart cannot be displayed A chart will not be displayed in the following conditions: • When the chart scale is too large or too small. • When scrolling the chart outside the indices.
2. PLOTTER OPERATION 2.5.3 FURUNO and NavCharts™ charts Chart symbols The table below shows FURUNO and NavCharts™ chart symbols and their meanings. Chart symbols Symbol Symbol Description Description Summit Position of Sounding Wreck Obstruction Lighthouse Fishing Reef Lighted Buoy Platform Buoy Anchorage Radio Station Data for aids to navigation Selected FURUNO and NavCharts™ charts can show buoy and lighthouse data. Simply place the cursor on the lighthouse or buoy mark.
2. PLOTTER OPERATION Port service icons (NavCharts™ only) Selected NavCharts show services available at ports, with icons. 1. Use the cursor pad to place the cursor on the sailboat icon (denotes a port or harbor) desired. 2. Push the [ENTER] knob. 3. Use ◄ or ► to select icon desired at the top of the display. The services available appear directly below the icon selected. 4. Press the RETURN soft key to finish. Detailed information of service selected List of services at the port selected + 34° 22.
2. PLOTTER OPERATION 2.5.4 C-MAP charts Cursor and data display Besides its fundamental functions of providing position data, the cursor can also show information about caution area, depth area, source of data, etc. on C-MAP charts. In addition, you can display information about an icon by placing the cursor on it. 1. Press the cursor pad to turn the cursor on. 2. Use the cursor pad to place the cursor on the position desired. 3. Push the [ENTER] knob to open the Objects window.
2. PLOTTER OPERATION Icon data You may place the cursor on any icon to find information about the selected icon. 1. For example, place the cursor on a lighthouse icon. Place the cursor on a lighthouse icon. + 34° 22. 3456'N 080° 22. 3456'E 359.9°M TRIP NU 19.9 kt 99.9 nm 16.0nm MARK ENTRY MODE NTH UP CENTER GO TO CURSOR D. BOX ON /OFF Lighthouse icon 2. Push the [ENTER] knob to show data. For example, the following window appears for a lighthouse.
2. PLOTTER OPERATION Navigation mark, fixed Light. Color white Height 7. 00 Meters Light characteristic occulting XXXXXXXX XXXXXXXX Sample lighthouse data 5. Press the RETURN soft key twice to close the Objects window. Tide information The C-MAP chart card provides for calculation of the tide heights for any date. Additionally it displays the times of sunrise and sunset. 1. Press the cursor pad to place the cursor on a Tide icon ( 2. Push the [ENTER] knob to open the Objects window. 34 24. 3456 N 359.
2. PLOTTER OPERATION Horizontal Cursor 34 24. 3456 N 359.9 +124 0.86 24. 3456 W 59.9kt NU 024nm 0.74 DATE 0.61 0.48 Vertical Cursor 0.35 0 4 8 12 16 20 24 Time: 04:35 Height: 0.45ft Draught: 0.65ft 01/07/30 +13:30 43° 32.860N 010° 18.022E RETURN Port info LIVORNO (LEGHORN) High Water(max) 0.86ft(13:30 L) Low Water(min) 0.35ft(21:00 L) Sunrise 07:52L Sunset 16:53 L Tide window 5. Press the DATE soft key to open the DATE window. CHANGE DATE (DAY. MONTH. YEAR) 01. 01. 2001 LIMIT: 31.12.
2. PLOTTER OPERATION 2.6 Working with Track Your ship’s track is plotted on the screen using navigation data fed from position-fixing equipment. This section shows you what you can do with track, from turning it on or off to changing its plotting interval. Own ship’s track is displayed in the default setting and on the color model it is red. 2.6.1 Displaying track Own ship track 1. Press the [MENU] key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. PLOTTER OPERATION Target track Target track, NMEA format TTM (Tracked Target Message) data sentence, may be turned on or off as desired. The default setting is ON. 1. Press the [MENU] key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu. 2. Use the cursor pad to select TARGET TRACK DISPLAY. 3. Press the EDIT soft key to show the target track display window. 4. Use the cursor pad to select to ON or OFF as appropriate. 5. Press the ENTER soft key. 6.
2. PLOTTER OPERATION 2.6.3 Changing track color (GD-1700C/1710C) Track can be displayed in red (default setting), yellow, green, light-blue, purple, blue and white. It can be useful to change track color on a regular basis to discriminate between previous day’s track, etc. Own ship’s track 1. Press the [MENU] key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu. 2. Use the cursor pad to select OWN SHIP TRACK COLOR. 3.
2. PLOTTER OPERATION 2.6.4 Track plotting method and interval for own ship track In drawing the own ship track, first the ship’s position fed from position-fixing equipment is stored into the unit’s memory at an interval of time or distance. A shorter interval provides for better reconstruction of the track, but the storage time of the track is reduced. When the track memory becomes full, the oldest track is erased to make room for the latest.
2. PLOTTER OPERATION 4. Use the [ENTER] knob and the cursor pad to enter numeric data. The [CLEAR] key functions to clear an entire line of data. 5. Push the [ENTER] knob or ENTER soft key. 6. Press the [MENU] key to close the menu. 2.6.5 Changing own ship track/mark distribution setting The equipment stores a total of 8000 points of track and marks. This amount may be distributed as desired, and the default setting is 2000 points of track and 6000 marks.
2. PLOTTER OPERATION 2.6.6 Erasing track This paragraph shows you how to erase own ship’s track and target tracks. You can erase ship’s track three ways: collectively, by color (color model only) and by area. Erasing own ship track by area You can erase own ship’s track by area as below. This feature is not available when the overlay mode (GD-1700C/1710C only) is in use. 1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. PLOTTER OPERATION Erasing own ship track by color (GD-1700C/1710C) You may erase own ship’s track by color as follows: 1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu. 2. Use the cursor pad to select ERASE TRACKS BY COLOR, then press the EDIT soft key. ERASE TRK BY COLOR ▲ ¤ RED ¡ YELLOW ¡ GREEN ¡ LIGHT BLUE ¡ PURPLE ¡ BLUE ¡ WHITE ▼ Erase track by color window 3.
2. PLOTTER OPERATION 2.7 Marks, Lines Marks are useful for denoting important points such as a good fishing spot. Marks can be inscribed in seven shapes and seven colors (GD-1700C/1710C): Red, yellow, green, light-blue, purple, blue and white. ¡ ✕ Mark shapes 2.7.1 Entering a mark, line 1. Place the cursor where you want a mark to appear. 2. Press the MARK ENTRY soft key. (Press the [HIDE/SHOW] key if the plotter soft keys are not shown.
2. PLOTTER OPERATION 4. Select MARKS SHAPE, then press the EDIT soft key. MARKS SHAPE ▲ ¤ ¡ ¡ ¡ ¡ ✕ ¡ ¡ ¡ ▼ Mark shape window 5. Use the cursor pad to select mark shape desired, then press the RETURN soft key. 6. Select MARKS SIZE, then press the EDIT soft key. 7. Use the cursor pad to select LARGE (default setting) or SMALL as appropriate. 8. Press [ENTER] knob or ENTER soft key. 9. Press the [MENU] key twice to close the menu. 2.7.
2. PLOTTER OPERATION LINES STYLE ▲ ¤ ¡ ¡ ¡ - - - - ▼ Mark line window 3. Use the cursor pad to select line style desired. Press the ENTER soft key. Line style “dot” disables line drawing. The joint between lines is determined by mark shape. For example, selecting the circle shape will join lines with a circle as below. 4. Press the [MENU] key twice to close the menu. 2.7.4 Erasing marks, lines Erasing an individual mark 1. Operate the cursor pad to place the cursor on the mark you want to erase. 2.
2. PLOTTER OPERATION Erasing all marks, lines You can erase all marks and lines collectively. Be absolutely sure you want to erase all marks and lines - erased marks and lines cannot be restored. 1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu. 2. Use the cursor pad to select ERASE ALL MARKS/LINES, then press the EDIT soft key. 3. Push the [ENTER] knob to erase all marks and lines. 4. Press the [MENU] key twice to close the menu.
2. PLOTTER OPERATION 2.8 Waypoints In navigation terminology, a waypoint is a particular location on a voyage whether it be a starting, intermediate or destination point. A waypoint is the simplest piece of information your equipment requires to get you to a destination, in the shortest distance possible. This unit has 999 waypoints into which you can enter position information.
2. PLOTTER OPERATION 7. Press the MARK SHAPE soft key to open the mark shape selection window. SELECT MARK Waypoint mark shape selection window 8. Operate the cursor pad to select shape desired. 9. Press the ENTER soft key. 10. For the GD-1700C/1710C, press the SELECT MARK and MARK COLOR soft keys in that order to open the waypoint mark color selection window. Select color desired, then press the ENTER soft key.
2. PLOTTER OPERATION Entering a waypoint by range and bearing This method is useful when you want to enter a waypoint using range and bearing to a target found on a radar. 1. Press the [MENU] key to open the menu. 2. Press the WAYPOINTS/ROUTES, WAYPOINTS and WAYPOINT BY RNG & BRG soft keys. 3. An “X” (red on the GD-1700C/1710C) appears at own ship position, and it is the origin point for range and bearing. Operate the cursor pad to place the cursor on the location desired.
2. PLOTTER OPERATION Entering a waypoint from the waypoint list You can manually enter waypoint position from the waypoint list as follows: 1. Press the [MENU] key to open the menu. 2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys. 3. Press the LOCAL LIST (lists waypoints in order from nearest to furthest) or ALPHANUMERIC LIST (lists waypoints in alphanumeric order) soft key. WPT ALPHA 35°47.010'N 135°21.000'W 350.9° 3.80 nm CRAB 00:00 01JAN01 34°42.000'N 135°21.050'W 050.9° 1.98 nm 065.9° 1.
2. PLOTTER OPERATION 7. Press the SAVE soft key. 8. Press the [MENU] key to close the menu. Editing a waypoint from the plotter display You may edit waypoints from the plotter display as follows: 1. Press the [MENU] key followed by the WAYPOINTS/ROUTES and WAYPOINTS soft key to open the waypoint menu. 2. Press the WAYPOINT BY CURSOR soft key. 3. Operate the cursor pad to place the cursor on the waypoint which you want to change. A flashing diamond mark appears on the waypoint when it is correctly selected.
2. PLOTTER OPERATION 2.8.3 Erasing waypoints Erasing a waypoint directly from the plotter display 1. Operate the cursor pad to place the cursor on the waypoint you want to erase. A flashing diamond mark appears over the waypoint when the waypoint is correctly selected. 2. Press the [CLEAR] key. You are asked if you are sure to erase the waypoint. 3. Push the [ENTER] knob. The waypoint is erased from the plotter screen and the waypoint list. Erasing a waypoint from the menu 1.
2. PLOTTER OPERATION 2.8.4 Changing waypoint mark size (FURUNO, NavCharts™) You may change the size of all waypoint marks to small or large (default), or you may turn them off. 1. Press the [MENU] key to open the menu. 2. Press the CHART SETUP and CHART DETAILS soft keys.
2. PLOTTER OPERATION 2.8.5 Searching waypoints You can search for a waypoint through the alphanumeric waypoint list as follows: 1. Press the [MENU] key. 2. Press the WAYPOINTS/ROUTES, WAYPOINTS and ALPHANUMERIC LIST soft keys to show the alphanumeric list. ▲ ▲ ABALONE 00:00 01JAN01 35°47.010'N 135°21.000'W 350.9° 3.80 nm CRAB 00:00 01JAN01 34°42.000'N 135°21.050'W 050.9° 1.98 nm FISH 00:00 01JAN01 34°41.000'N 135°21.030'W 065.9° 1.83 nm LOBSTER 00:00 01JAN01 38°44.300'N 135°21.010'W 144.9° 4.
2. PLOTTER OPERATION 2.9 Routes Often a trip from one place to another involves several course changes, requiring a series of route points (waypoints) which you navigate to, one after another. The sequence of waypoints leading to the ultimate destination is called a route. Your unit can automatically advance to the next waypoint on a route, so you do not have to change the destination waypoint repeatedly. You can store up to 200 routes, and a route may have 35 waypoints. 2.9.
2. PLOTTER OPERATION 5. If desired you can change the route name shown and/or add a comment. A route name may consist of six characters; comment, 13 characters. 6. Press the LOCAL LIST or ALPHA LIST soft key to open the waypoint list. 7. Use the cursor pad to select a waypoint, then press the ADD WPT soft key to add it to the route. 8. Repeat step 7 to complete the route. Note: To clear a waypoint, press the ERASE LST WP soft key. Each press of this key deletes the last waypoint entered. 9.
2. PLOTTER OPERATION Creating voyage-based routes You can create routes based on your ship’s track. The route can be created automatically by time or distance, or manually. This feature is useful when you wish to retrace previous track. The “SAVE” icon ( V E ) appears at the top of the screen when a voyage-based route is being created. SA 1. Press the [MENU] key to open the menu. 2. Press the WAYPOINTS/ROUTES soft key. 3. Press the CREATE VOYAGE-BASED ROUTE soft key. ▲ 001 ROUTE LENGTH WAYPOINTS 35 25.
2. PLOTTER OPERATION 6. Choose how to record points for your route, by time, by distance or manual entry, by pressing by one of BCKTRK TIME, BCKTRK RANGE or MANUAL soft key as appropriate. For manual entry, go to step 8. For BCKTRK TIME, BCKTRK DIST one of the following displays appears. TIME INTERVAL DISTANCE INTERVAL 00h01m (When selecting BCKTRK TIME.) 00.1nm (When selecting BCKTRK DIST.) Displays for entry of time, distance interval 7. Enter interval desired with the cursor pad and [ENTER] knob.
2. PLOTTER OPERATION 2.9.2 Connecting routes Two routes which you have created can be connected as follows to form a new route. 1. 2. 3. 4. 5. 6. 7. Press the [MENU] key to open the menu. Press the WAYPOINTS/ROUTES soft key. Press the ROUTES soft key. Press the NEW ROUTE soft key. If desired enter name and comment for route. Press the CONNECT soft key. Use the cursor pad and the [ENTER] knob to enter the route name for the first route, beneath FIRST in the connect route window.
2. PLOTTER OPERATION 2.9.3 Inserting waypoints in a route Waypoints can be inserted in a route as follows: Inserting a waypoint from the route list 1. 2. 3. 4. 5. 6. Press the [MENU] key to open the menu. Press the WAYPOINTS/ROUTES soft key. Press the ROUTES soft key. Use the cursor pad to select a route. Press the EDIT ROUTE soft key. The route name screen appears. Press the LOCAL LIST soft key. EDIT ROUTE ROUTE NAME: 001 COMMENT: 01 001WPT 34°44.111'N 135°21.134'W LEG ▲ 29.9° 12.
2. PLOTTER OPERATION 9. Use the cursor pad to select the waypoint you want to insert. (You can switch between the local list and alphanumeric list by using the LOCAL LIST and ALPHA LIST soft keys.) 10. Press the SELECT WPT or CHANGE WPT soft key, whichever is displayed. 11. Press the [MENU] key to close the menu. Inserting a waypoint from the plotter display Inserting a waypoint before first waypoint or after last waypoint in a route 1. 2. 3. 4. 5. 6. 7. Press the [MENU] key to open the menu.
2. PLOTTER OPERATION 2.9.4 Removing waypoints from a route Removing a waypoint from the route list 1. 2. 3. 4. 5. 6. 7. 8. Press the [MENU] key to open the menu. Press the WAYPOINTS/ROUTES soft key. Press the ROUTES soft key. Select a route. Press the EDIT ROUTE and LOCAL LIST soft keys. Select the waypoint you want to remove. Press the REMOVE WPT soft key. Press the [MENU] key to close the menu. Removing a waypoint from the plotter display 1. 2. 3. 4. 5. 6. 7. Press the [MENU] key to open the menu.
2. PLOTTER OPERATION 2.10 Navigation This section shows you how to get to a desired destination by “quick points,” waypoints, port services and routes. Note: Reciprocal setting and canceling of destination is available by outputting the data sentence ZDA from the NavNet unit connected to the navigator. 2.10.1 Navigating to a “quick point” The “quick point” feature allows you to navigate to point(s) without retaining the data indefinitely in your unit’s memory.
2. PLOTTER OPERATION Navigating to multiple quick points 1. Select “35 POINTS” following the procedure in “Selecting quick point entry method” on the previous page. 2. Press the GOTO soft key. 3. Place the cursor on an existing waypoint (SELECT WPT soft key appears) or a new location (ADD QP soft key appears). 4. Depending on the action taken at step 3, press the SELECT WPT or ADD QP soft key. “QP<01>” appears at the cursor location if a quick point is selected.
2. PLOTTER OPERATION Selecting an external waypoint You can select a waypoint (or route) entered at an external plotter connected with NMEA cable. This function requires RMB sentence. 1. Press the [MENU] key, PLOTTER SETUP soft key to show the PLOTTER SETUP menu. 2. Use the trackball to select QP. 3. Press the ENTER soft key or [ENTER] key to show the QP window. QP ¡ EXT WPT (RMB) ¤ INTERNAL QP window 4. Select EXT WPT (RMB). 5.
2. PLOTTER OPERATION PORT & SERVICE SELECT PORT & SRVC ▼ ▲ ¡ ¡ ¤ ¡ ACCIAROLI ACQUAMORTA AGNONE S. NICOLA AGROPOLI AMALFI BAIA CAPRI CASA MICCIOLA-ISCHIA TM Port list (NavChart , Italy) ¡ ¡ ¡ ¡ PORT & SERVICE WC ▼ TM Port services (NavChart ) Port services (C-MAP) Port services and sample port list 4. If you selected PORT (NavCharts™ only) at step 3, use the cursor pad to select a port and press the ENTER soft key. Make a route using the soft keys, then push the [ENTER] knob.
2. PLOTTER OPERATION 2.10.4 Following a route Selecting the route to follow 1. 2. 3. 4. 5. Press the [MENU] key to open the menu. Press the WAYPOINTS/ROUTES soft key. Press the ROUTES soft key to open the route list. Select a route. Press the GOTO soft key to show the plotter display. The cursor is on the waypoint nearest own ship. FISH 359.2°M 104.5°M 83.2nm 10.0 kt GOTO ROUTE 16.0 nm WP-002 GOTO WPT FISH RVRSE ROUTE WP-001 RETURN CRAB Plotter display, route selected as destination 6.
2. PLOTTER OPERATION Restarting navigation When you steer to avoid an obstacle or the vessel drifts, you may go off your intended course, as in Line 1 in the figure below. Also, if you don’t need to return to the original course, you can go directly to the next waypoint, as in Line 2 in the figure below. In these cases, use the restart function to restart navigation. Line 2 Obstacle Line 1 Original course Example of when to restart navigation 1. Press the [MENU] key to open the menu. 2.
2. PLOTTER OPERATION Setting speed for ETA calculation Speed, which may be input manually or automatically, is required to calculate ETA (Estimated Time of Arrival) to a destination. 1. 2. 3. 4. Press the [MENU] key to open the menu. Press the WAYPOINTS/ROUTES soft key. Press the LOG soft key. Press the SPEED soft key. SPEED FOR ETA ▲ ¤ SPD 010.0kt ¡ GPS AVG. SPEED ▼ Select speed for ETA window 5. Enter speed manually in the SPD field, or use GPS speed data (if applicable) by selecting GPS AVG. SPEED. 6.
2. PLOTTER OPERATION To select waypoint switching method do the following: 1. 2. 3. 4. 5. Press the [MENU] key. Press the PLOTTER SETUP soft key. Use the cursor pad to select WAYPOINT SWITCHING. Press the EDIT soft key to show the waypoint switching window. Use the cursor pad to select appropriate waypoint switching method; PERPENDICULAR, ARRVL ALM CRCL (default setting), or MANUAL. 6. Press the ENTER soft key or [ENTER] knob. 7. Press the [MENU] key to close the menu. 2.10.
2. PLOTTER OPERATION 2.11 Alarms The plotter section has eight conditions which generate both audio and visual alarms: arrival alarm, anchor watch alarm, XTE (Cross Track Error) alarm, proximity alarm, speed alarm, trip alarm, water temperature alarm and bottom alarm. (The bottom and water temperature alarms, which require depth and water temperature data, may also be set on the sounder alarm menu. For these alarms see Chapter 4.
2. PLOTTER OPERATION 2.11.2 Arrival alarm The arrival alarm informs you that your boat is approaching a destination waypoint. The area that defines an arrival zone is that of a circle which you approach from the outside of the circle. The alarm will be released if your boat enters the circle. When the arrival alarm is active a dashed circle (red on the GD-1700C/1710C) marks the arrival alarm area. Note: Arrival alarm and anchor watch alarm cannot be set together.
2. PLOTTER OPERATION 2.11.3 Anchor watch alarm The anchor watch alarm informs you that your boat is moving when it should be at rest. When the anchor watch is active, a dashed circle (red on the GD-1700C/1710C) with an “X” at its center marks the anchor watch area. Alarm setting Your ship's position where you start the anchor watch alarm. : Alarm area How the anchor watch alarm works 1. Press the [ALARM] key to open the alarm menu. 2. Use the cursor pad to select ANCHOR WATCH ALARM. 3.
2. PLOTTER OPERATION 2.11.4 XTE (Cross Track Error) alarm The XTE alarm warns you when your boat is off its intended course. When the XTE alarm is active two dashed lines (red on the GD-1700C/1710C) mark the XTE alarm area. Own ship position Alarm setting Destination waypoint Intended course : Alarm How the XTE alarm works 1. Press the [ALARM] key to open the alarm menu. 2. Use the cursor pad to select XTE ALARM. 3. Press the EDIT soft key to open the XTE alarm window. XTE ALARM ▲ ¡ ON 0.
2. PLOTTER OPERATION 4. Use the cursor pad to select WITHIN, UNDER/OVER, or OFF. 5. For WITHIN and UNDER/OVER, use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value. 6. Press the ENTER soft key or push the [ENTER] knob to register setting. 7. Press the [ALARM] key to close the menu. 2.11.
2. PLOTTER OPERATION 2.11.7 Trip alarm The trip alarm informs you when you have traveled a certain distance. 1. Press the [ALARM] key to open the alarm menu. 2. Use the cursor pad to select TRIP ALARM. 3. Press the EDIT soft key to show the trip alarm window. TRIP ALARM ▲ ¡ ON 0000.0nm ¤ OFF ▼ Trip alarm window 4. Select ON with the cursor. 5. Use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value. 6.
2. PLOTTER OPERATION 2.11.8 Alarm information When an alarm setting has been violated, the buzzer sounds and the speaker icon appears, in red on the color model. Press the [CLEAR] key to silence the alarm. You can see which alarm has been violated on the ALARM menu. In the example below the arrival alarm has been violated. 1. Press the [ALARM] key. The name of the offending alarm is shown in the alarm information window. AUDIO ALARM INT & EXT BUZZ ARRIVAL ALARM ON 0.010nm ANCHOR WATCH ALARM OFF 0.
2. PLOTTER OPERATION Alarm messages The table below shows the plotter alarm messages and their meanings. Plotter alarm messages and their meanings Message ARRIVED AT XXX WAYPOINT! (XXX = waypoint name) ENTERED INTO AVOIDANCE AREA! EXCEEDED ANCHOR WATCH LIMIT! EXCEEDED XTE LIMIT! SPEED ALARM! TEMPERATURE ALARM! TRIP ALARM! MILEAGE EXCEEDED 2.12 Meaning Arrival alarm violated. Proximity alarm violated. Anchor watch alarm violated. XTE alarm violated. Speed alarm violated. Water temperature alarm violated.
3. RADAR OPERATION This chapter covers radar operation, including the ARP (Auto Plotter) function. ARP requires a Model 1800/1900 series network radar equipped with the ARP circuit board. 3.1 Radar Display Cursor North marker Heading M: Magnetic T: True Pulselength Range/ range ring interval Presentation mode ..250 /SP.125nm Heading line 319.
3. RADAR OPERATION 3.2 Transmitting, Stand-by 1. 2. 3. 4. 5. Confirm that the network radar is plugged in. Press the [DISP] key to select a radar display. Press the [POWER/BRILL] key momentarily. Press the RADAR STBY soft key to highlight TX on its label. Press the RETURN soft key. When the radar picture is not required, but you want keep it in a state of readiness, press the RADAR TX soft key to highlight STBY on its label. 3.
3. RADAR OPERATION 1. Press the [GAIN] key. The last-used “adjustment window” is displayed. In the example below, the gain sensitivity adjustment window is shown. The gain soft keys shown depend on radar source as shown below. Item selected for adjustment is highlighted. 319.9°M .250/SP.125nm H-UP GAIN ADJUST ¤ AUTO ¡ AUTO ¡ AUTO ¡ MAN ROUGH MODERATE CALM 0 H-UP + GAIN ADJUST GAIN GAIN A/C SEA A/C SEA A/C RAIN A/C RAIN FTC A/C AT ON /OFF RETURN GAIN SENSITIVITY 319.9°M .250/SP.
3. RADAR OPERATION 3.5 Reducing Sea Clutter 3.5.1 How the A/C SEA works Echoes from waves can be troublesome, covering the central part of the display with random signals known as “sea clutter”. The higher the waves and the higher the antenna above the water, the further the clutter will extend. Sea clutter may affect radar performance because real targets are sometimes hidden by the echoes of small waves. (See the left-hand figure in the figure below.
3. RADAR OPERATION 5. When the radar source is the Model 1800/1900 series radar, A/C SEA and A/C RAIN can be automatically adjusted. Press the A/C AT soft key to select ON or OFF as appropriate. When turned on, it overrides A/C SEA and A/C RAIN settings. 6. Press the [GAIN] key on the front panel or RETURN soft key to finish. 3.6 Reducing Precipitation Clutter The vertical beamwidth of the antenna is designed to see surface targets even when the ship is rolling.
3. RADAR OPERATION 3.6.2 Adjusting the FTC To suppress rain clutter from heavy storms or scattered rain clutter, adjust the FTC, which is available with the Model 1700 series network radar. The FTC splits up these unwanted echoes into a speckled pattern, making recognition of solid targets easier. Note: In addition to reducing clutter, the FTC can be used in fine weather to clarify the picture when navigating in confined waters. However, with the circuit active the receiver is less sensitive.
3. RADAR OPERATION 3.7 Range Scale The range setting determines the size of the area (in nautical miles) that will appear on your display. In addition, the range setting will also automatically adjust the range ring interval so that accurate range measurements may be made while operating on any range setting. The range, range ring interval and pulselength appear at the top left-hand corner of the display. Press the [RANGE (+ or -)] key to change the range scale. Range scales (nm, sm) Range 0.125 0.
3. RADAR OPERATION 3.8 Pulselength The pulselength in use is displayed at the upper left corner of the display. Appropriate pulselengths are preset to individual range scales. Therefore, you are not usually required to select them. If you are not satisfied with the current pulselength setting, however, it is possible to change it for the ranges shown below. Generally, select a longer pulse for longer detection range and shorter pulse for better range discrimination. 1.5 nm 1.
3. RADAR OPERATION 3.9 Presentation Mode This unit provides four radar presentation modes: head-up, course-up, north-up and true motion. Heading data is required for modes other than head-up. 3.9.1 Selecting a presentation mode 1. If not displayed, press the [HIDE/SHOW] key to show soft the radar soft keys. 2. Press the RADAR DISPLY soft key to show the RADAR DISPLAY soft keys. .250/SP.125nm H-UP 319.9°M RADAR DISPLAY 319.9°M .250/SP.
3. RADAR OPERATION 3.9.2 Description of presentation modes Head-up (H-UP) A display without azimuth stabilization in which the line connecting the center with the top of the display indicates own ship’s heading. Targets are painted at their measured distances and in their directions relative to own ship’s heading. The short line on the bearing scale is the north marker.
3. RADAR OPERATION North-up (N-UP) In the north-up mode, targets are painted at their measured distances and in their true (compass) directions from own ship. North is maintained at the top of the screen. The heading line changes its direction according to ship’s heading. North Heading Line North-up presentation mode True motion (TR-M) Fixed radar targets maintain a constant position on the screen, while your own ship moves across the radar image at the correct speed and heading.
3. RADAR OPERATION 3.10 Measuring the Range You can measure the range to a radar target three ways: by the range rings, by the cursor, and by the VRM (Variable Range Marker). 3.10.1 Measuring range by range rings Count the number of rings between the center of the display and the target. Check the range ring interval and judge the distance of the echo from the inner edge of the nearest ring. To turn the range rings on, do the following: 1.
3. RADAR OPERATION 3.10.2 Measuring range by cursor Operate the cursor pad to place the cursor intersection on the inside edge of the radar target. The range to the target, as well as the bearing, appears to the right of “+” at the bottom of the display. Target .250/SP.125nm H-UP 319.9°M SIGNAL PROC Cursor RADAR DISPLY NAV FUNC TARGET ZOOM & D. BOX + 359.9°R 0.
3. RADAR OPERATION 3.10.3 Measuring range by VRM 1. Press the [EBL/VRM] key to display the EBL/VRM soft keys. .250/SP.125nm H-UP 319.9°M EBL VRM EBL1 ON VRM1 ON OFFSET EBL2 ON VRM2 ON + 359.9°R 0.240nm EBL/VRM soft keys 2. Press the VRM1 ON (dotted ring VRM) or VRM2 ON (dashed ring VRM) soft key to select the desired VRM. The selected VRM’s indication, at the bottom of the screen, is highlighted. 3. Rotate the [ENTER] knob the place the VRM on the inside edge of a radar target.
3. RADAR OPERATION 3.10.4 Erasing a VRM, VRM indication Press appropriate VRM soft key, then press the [CLEAR] key. The VRM is erased and its indication becomes blank. 3.10.5 Erasing EBL/VRM data boxes Press the EBL or VRM soft key associated with the EBL/VRM data box you wish to erase. Press the [CLEAR] key once or twice to erase the data box. 3.10.6 Hiding EBL/VRM data boxes Press the ZOOM & D. BOX and D. BOX ON/OFF soft keys to show or hide the EBL/VRM data boxes. 3.10.
3. RADAR OPERATION 319.9°M .250/SP.125nm H-UP EBL VRM EBL1 ON EBL1 (Dotted line) VRM1 ON OFFSET EBL2 ON EBL2 (Dashed line) VRM2 ON EBL2 bearing EBL1 bearing R: Relative T: True EBL1 VRM1 330.1°R -.---nm EBL2 VRM2 234.1°R -.---nm + 359.9°R 0.240nm Active marker is highlighted. How to measure bearing with the EBL Note: The bearing to a target may be shown relative to own ship’s heading (Relative) or True bearing (requires heading data).
3. RADAR OPERATION 3.12 Erasing the Heading Line, North Marker The heading line indicates the ship's heading in all presentation modes. It is a line from the own ship position to the outer edge of the radar display area and appears at zero degrees on the bearing scale in head-up mode; it changes its orientation in the north-up, course-up and true motion modes with ship’s movement. The north marker appears as a short dashed line.
3. RADAR OPERATION 3.14 Reducing Radar Interference Radar interference may occur when near another shipborne radar that is operating in the same frequency band as your radar. Its on-screen appearance looks like many bright dots either scattered at random or in the form of dotted lines extending from the center to the edge of the display. Interference effects are distinguishable from normal echoes because they do not appear in the same place on successive rotations of the scanner.
3. RADAR OPERATION 3.15 Zoom The zoom feature allows you to double the size of the area selected with the “zoom circle.” It is available on any range but is inoperative in true motion and when the display is shifted. 3.15.1 Zooming in on radar targets 1. 2. 3. 4. If not displayed, press the [HIDE/SHOW] key to show the radar soft keys. Use the cursor pad to set the cursor where you want to zoom. Press the ZOOM & D. BOX soft key to show ZOOM & D. BOX soft keys.
3. RADAR OPERATION SELECT TARGET NO. ▲ 1 ▼ Target no. selection window 5. Use the [ENTER] knob to select number (1-10), then push the [ENTER] knob. If the target does not exist several beeps sound and the zoom function is cancelled. To cancel, press the CURSOR LOCK soft key. Note: The zoom window blends in with the background when the background color for the radar picture is white. If the window is difficult to see, change the background color. 3.
3. RADAR OPERATION 3.16.2 Automatic shift The amount of automatic shift is calculated with speed, and the amount of shift is limited to 60% of the range in use. For example, if you set the shift speed setting for 15 knots and the ship is running at 10 knots, the amount of shift will be 40%. The formula for determining shift amount is as shown below. Ship's speed X 0.6 = Amount of shift(%) Shift speed setting Automatic shift mode is only available in the head-up mode.
3. RADAR OPERATION 3.17 Using the Offset EBL The offset EBL can be used to predict a potential collision course. It can also be used to measure the range and bearing between two targets. 3.17.1 Predicting collision course The procedure below may be used to check if a radar target is on a potential collision course with your vessel. 1. Press the [EBL/VRM] key to show the EBL/VRM soft keys. 2. Press the EBL1 ON soft key to turn on the EBL1. 3. Press the OFFSET soft key.
3. RADAR OPERATION 3.17.2 Measuring range & bearing between two targets The procedure which follows shows how to measure the range and bearing between two targets, using the targets “A” and “B” in the figure below as an example. 1. 2. 3. 4. 5. 6. 7. 8. 9. Operate the cursor pad to place the cursor on the target “A.” Press the [EBL/VRM] key to show the EBL/VRM soft keys. Press the EBL1 ON soft key to turn on the EBL1. Press the OFFSET soft key.
3. RADAR OPERATION 3.18 Echo Trails Echo trails are simulated afterglow of target echoes that represent their movements relative to own ship. This function is useful for alerting you past possible collision situations. Echo trail Sample echo trails 3.18.1 Trail time 1. If not displayed, press the [HIDE/SHOW] key to show the radar soft keys. 2. Press the TARGET soft key. 3. Press the TRAIL soft key. .250/SP.125nm H-UP 319.9°M TRAIL .250/SP.125nm H-UP 319.
3. RADAR OPERATION 5. Use the cursor pad to select time desired. 6. Press the ENTER soft key. 7. Press the RETURN soft key twice to finish. 3.18.2 Starting echo trails 1. 2. 3. 4. If not displayed, press the [HIDE/SHOW] key to display the radar soft keys. Press the TARGET and TRAIL soft keys. Press the TRAIL ON/OFF to select ON. Press the RETURN soft key twice to finish. “TRAIL,” the echo trail time selected and elapsed time appear at the top right-hand corner of the display.
3. RADAR OPERATION 3.18.5 Trail color (GD-1700C/1710C) The GD-1700C/1710C can show echo trails in blue, yellow, green or white. 1. If not displayed, press the [HIDE/SHOW] key to display the radar soft keys. 2. Press the TARGET, TRAIL and TRAIL COLOR soft keys. TRAIL COLOR ▲ ¤ BLUE ¡ YELLOW ¡ GREEN ¡ WHITE ▼ Trail color window 3. Use the cursor pad to select the color desired. 4. Press the ENTER soft key. 5. Press the RETURN soft key twice to finish.
3. RADAR OPERATION 3.19 Echo Stretch Normally, the reflected echoes from long range targets appear on the display as weaker and smaller blips even though they are compensated by the radar’s internal circuitry. The echo stretch function magnifies these small blips in all ranges. Two types of echo stretch are available: ES LOW which stretches echoes in bearing direction and ES HIGH which stretches them in both range and bearing directions.
3. RADAR OPERATION 3.20 Echo Averaging The echo average feature, available with connection of a Model 1800/1900 series network radar, effectively suppresses sea clutter. Echoes received from stable targets such as ships appear on the screen at almost the same position during every rotation of the antenna. On the other hand, unstable echoes such as sea clutter appear at random positions. To distinguish real target echoes from sea clutter, echo average performs scan-to-scan correlation.
3. RADAR OPERATION 3.21 Outputting TLL Data Target position data can be output to NavNet equipment and shown on their plotter screens with the TTL mark ( X ) 1. If not displayed, press the [HIDE/SHOW] key to display the radar soft keys. 2. Operate the cursor pad to place the cursor on the target whose position you wish to output. 3. Press the TARGET soft key. .250/SP.125nm H-UP 319.9°M TARGET TRAIL TLL OUTPUT ACQ TARGET INFO Requires ARP circuit board in Model 1800/1900 series NavNet radar.
3. RADAR OPERATION 3.22 Guard Alarm The guard alarm allows the operator to set the desired range and bearing for a guard zone. When ships, islands, landmasses, etc. violate the guard zone, an audio alarm sounds and the offending target blinks to call the operator’s attention. CAUTION • The alarm should not be relied upon as the sole means for detecting possible collision situations.
3. RADAR OPERATION The equipment then searches for targets inside the guard zone to determine guard alarm type. If a target is found inside the guard zone, the guard zone type becomes an “Outward guard alarm,” and any target exiting the guard zone will trigger the audio alarm. If no target is found, the guard zone type becomes an “Inward guard alarm,” and any targets entering the guard zone will trigger the audio alarm. The guard alarm type is shown as G1(G2) IN or G1(G2) OUT.
3. RADAR OPERATION 3.23 Watchman 3.23.1 How watchman works The watchman function periodically transmits radar pulses for one minute to check for targets in a guard zone. If a target is found in the zone, watchman is cancelled, the audio alarm sounds and the radar continues transmitting. If no target is found the radar goes into standby for the number of minutes set on the RADAR DISPLAY SETUP menu.
3. RADAR OPERATION 3.24 Waypoint Marker A waypoint marker, showing the location of the destination waypoint set on the plotter, may be inscribed on the radar display. .250/SP.125nm H-UP Waypoint marker 319.9°M NAV + W. MAN ON/OFF FUNC WPT MK ON /OFF RETURN + 359.9°R 0.240nm Waypoint marker 1. 2. 3. 4. If not displayed, press the [HIDE/SHOW] key to display the radar soft keys. Press the NAV FUNC soft key. Press the WPT MK ON/OFF soft key to select ON or OFF as appropriate.
3. RADAR OPERATION 3.25 ARP, TTM Operation With an ARP-equipped Model 1800/1900 series network radar as the radar source, you can manually and automatically acquire and track ten targets. Once a target is acquired automatically or manually it is automatically tracked within 0.1 to 32 nm. If the FURUNO heading sensor PG-1000 is used, the data sentence “RMC” is necessary.
3. RADAR OPERATION 3.25.1 Activating/deactivating ARP, TTM 1. Press the [MENU] key followed by the ARP SETUP soft key to show the ARP SETUP menu. ARP TARGET INFO INTERNAL ARP CANCEL ALL TARGETS NO ARP VECTOR MODE TRUE ARP VECTOR TIME 30 minutes HISTORY INTERVAL OFF CPA OFF TCPA 30 seconds AUTO ACQUISITION AREA OFF TARGET ID NUMBER OFF ARP SETUP EDIT RETURN ARP setup menu 2. Select ARP TARGET INFO, then press the EDIT soft key to show the ARP target info window.
3. RADAR OPERATION 3.25.2 Acquiring and tracking targets (ARP) Ten targets may be acquired and tracked manually and automatically. When you attempt to acquire an eleventh target, the message “ARP FULL – ALREADY TRACKING 10 TARGETS!” appears for five seconds. To acquire another target, terminate tracking of an unnecessary target as shown in the paragraph 3.25.4. Manual acquisition When the automatic acquisition (AUTO ACQ. AREA) is set to on, up to five targets may be acquired manually.
3. RADAR OPERATION 7. Press the [MENU] key to close the menu. An acquisition area of 2.0 to 2.5 miles in range and ±45º on either side of the heading line in bearing appears. Note: Targets being tracked in automatic acquisition are continuously tracked when switching to manual acquisition. Automatic acquisition area 45° starboard 45° port 2.0 - 2.5 nm Automatic acquisition area 3.25.3 Displaying target number (ARP, TTM) Target number can be shown for ARP and TTM targets as below. .250/SP.
3. RADAR OPERATION 3.25.4 Terminating tracking of ARP targets When ten targets have been acquired, no more acquisition occurs unless targets are cancelled. If you need to acquire additional targets, you must first cancel one or more individual targets, or all targets, using one of the procedures below. Terminating tracking of selected targets 1. Place the cursor on the target to terminate tracking. 2. Press the [CLEAR] key to terminate tracking and erase the target. Terminating tracking of all targets 1.
3. RADAR OPERATION 3.25.5 Setting vector attributes (ARP) What is a vector? A vector is a line extending from a tracked target which shows estimated speed and course of the target. The vector tip shows an estimated position of the target after the selected vector time elapses. It can be useful to extend the vector length (time) in order to evaluate the risk of collision with any target.
3. RADAR OPERATION 3.25.6 Displaying past position display (ARP) This ARP can display time-spaced dots (maximum ten dots) marking the past positions of any targets being tracked. You can evaluate a target’s actions by the spacing between dots. Below are examples of dot spacing and target movement. (a) Ship turning (b) Ship running straight (c) Ship reduced speed (d) Ship increased speed Past position displays To turn the past position display on or off: 1.
3. RADAR OPERATION 3.25.7 ARP, TTM target data You can show motion trends (range, bearing, course, speed, CPA and TCPA) for ARP or TTM targets. Note that TARGET ID NUMBER, in the ARP SETUP menu, must be turned on to display this data. 1. Place the cursor on the target you want to see its data. 2. If not displayed, press the [HIDE/SHOW] key to display the radar soft keys. 3. Press the TARGET and TARGET INFO soft keys. The data of the selected target appears.
3. RADAR OPERATION 3.25.8 CPA/TCPA alarm (ARP) When the predicted CPA of any target becomes smaller than a preset CPA alarm range or its predicted TCPA less than a preset TCPA alarm limit, an audio alarm sounds and the speaker icon (red on the color model) appears. In addition, the target plot symbol of the offending target changes to a triangle and flashes together with its vector. You may silence the audio alarm with the [CLEAR] key. Press the [ALARM] key and the message “COLLISION ALARM” appears.
3. RADAR OPERATION TCPA ▲ ¤ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ▼ 30 seconds 1 minute 2 minutes 3 minutes 4 minutes 5 minutes 6 minutes 12 minutes TCPA window 8. Select a TCPA limit with the cursor pad. 9. Press the ENTER soft key. 10. Press the [MENU] key to close the menu. 3.25.9 Lost target alarm (ARP) When the system detects a lost target, the target symbol becomes a diamond and tracking is discontinued after one minute. The normal plotting symbol is restored to the target when the target is manually acquired.
3. RADAR OPERATION 3.26 Interpreting the Radar Display 3.26.1 General Minimum and maximum ranges Minimum range The minimum range is defined by the shortest distance at which, using a scale of 1.5 or 0.75 nm, a target having an echoing area of 10 m2 is still shown separate from the point representing the antenna position. It is mainly dependent on the pulselength, antenna height, and signal processing such as main bang suppression and digital quantization.
3. RADAR OPERATION Radar resolution There are two important factors in radar resolution (discrimination): bearing resolution and range resolution. Bearing resolution Bearing resolution is the ability of the radar to display the echoes received from two targets, which are at the same range and close together, as separate targets. Bearing resolution is directly proportional to the antenna length, and inversely proportional to the radar's wavelength.
3. RADAR OPERATION 3.26.2 False echoes Occasionally echo signals appear on the screen at positions where there is no target or disappear even if there are targets. False target situations may be recognized, however, if you understand why they are displayed. Typical false echoes are shown below. Multiple echoes Multiple echoes occur when a transmitted pulse returns from a solid object like a large ship, bridge, or breakwater.
3. RADAR OPERATION Virtual image A relatively large target close to your ship may show at two positions on the screen. One of them is the true echo directly reflected by the target and the other is a false echo which is caused by the mirror effect of a large object on or close to your ship as shown in the figure below. If your ship comes close to a large metal bridge, for example, such a false echo may temporarily be seen on the screen.
3. RADAR OPERATION 3.26.3 SART (Search and Rescue Transponder) A Search and Rescue Transponder (SART) may be triggered by any X-Band (3 cm) radar within a range of approximately 8 nm. Each radar pulse received causes it to transmit a response which is swept repetitively across the complete radar frequency band. When interrogated, it first sweeps rapidly (0.4 µs) through the band before beginning a relatively slow sweep (7.5 µs) through the band back to the starting frequency.
3. RADAR OPERATION General procedure for detecting SART response 1. Use the range scale of 6 or 12 nm as the spacing between the SART responses is about 0.6 nm (1125 m) to distinguish the SART. 2. Turn off the automatic clutter suppression (if applicable). 3. Turn off the Interference Rejector.
3. RADAR OPERATION A/C SEA control For optimum range SART detection, this control should be set to the minimum. Care should be exercised as wanted target in sea clutter may be obscured. Note also that in clutter conditions the first few dots of the SART response may not be detectable, irrespective of the setting of the anti-clutter sea control. In this case, the position of the SART may be estimated by measuring 9.5 nm from the furthest dot back towards own ship.
4. VIDEO SOUNDER OPERATION With connection of the optional network sounder you can show video sounder images on the display. 4.1 Principle of Operation The video sounder determines the distance between its transducer and underwater objects such as fish, lake bottom or seabed and displays the results on screen. It does this by utilizing the fact that an ultrasonic wave transmitted through water travels at a nearly constant speed of 4800 feet (1500 meters) per second.
4. VIDEO SOUNDER OPERATION 4.2 Sounder Displays 4.2.1 Selecting a sounder display There are seven display modes from which to choose: dual frequency, single frequency, marker zoom, bottom zoom, bottom lock, bottom discrimination, and A-scope To select a display; 1. Press the [DISP] key and select a sounder display. 2. If not displayed, press the [HIDE/SHOW] key to show the sounder soft keys. 3. Press the DISPLY MODE soft key to show the display mode window.
4. VIDEO SOUNDER OPERATION 4.2.2 Description of sounder displays Single frequency display Display mode Variable Range Marker (white) Depth scale Minute marker 0'30" Zero line Icons (alarm, battery, simulation) 0 S I SOUNDER SINGLE M F SHIFT 50 Color bar 40 Temp. scale (orange) 52 Fish echo 50 Cross-hair cursor 100 30 AUTO/ D. BOX FREQ LF /HF DISPLY MODE Water temp. graph Water temp.
4. VIDEO SOUNDER OPERATION Dual-frequency display The dual-frequency display provides both HF and LF pictures. This display is useful for comparing the same picture with two different sounding frequencies. 0.0 LF HF Dual-frequency display LF picture The sounder uses ultrasonic pulses to detect bottom conditions. The lower the frequency of the pulse, the wider the detection area. Therefore, the low frequency is useful for general detection and judging bottom condition.
4. VIDEO SOUNDER OPERATION Marker-zoom display The marker-zoom display expands a selected area of the normal sounder picture to full vertical size of the screen on the left-half window. You may specify the portion to expand by operating the VRM (Variable Range Marker), which you can shift with the [ENTER] knob. The area between the VRM and zoom marker is expanded. The length of the segment is equal to one division of the depth scale. Fish school 0'20" 0 42 Fish school 44 42.
4. VIDEO SOUNDER OPERATION Bottom-lock display The bottom-lock display provides a compressed normal picture on the right half of the screen and a 3 or 6 meter (10 or 20 feet) wide layer in contact with the bottom is expanded onto the left half of the screen. This mode is useful for discriminating bottom fish from the bottom echo. You may select the bottom lock range from the SOUNDER RANGE SETUP menu. For details, see paragraph 5.9.3. 0 20 - This part is zoomed.
4. VIDEO SOUNDER OPERATION A-scope display (display only) The A-scope display, available in all modes, shows echoes at each transmission with amplitudes and tone proportional to their intensities, on the right of the screen. It is useful for estimating fish species and seabed composition. To turn on the A-scope display, press the DISPLAY MODE soft key, select display mode desired, then press the A-SCPE soft key to turn the A-scope display on or off as appropriate.
4. VIDEO SOUNDER OPERATION 4.3 Automatic Sounder Operation Automatic sounder operation is useful when you are preoccupied with other tasks and do not have the time to adjust the display. 4.3.1 How the automatic sounder works The automatic sounder function automatically selects the proper gain, range scale and clutter suppression level according to depth. It works as follows: • Range changes automatically to locate the bottom on the lower half of screen.
4. VIDEO SOUNDER OPERATION 4.4 Manual Sounder Operation Manual operation is useful for observing fish schools and bottom using fixed gain setting. The gain, range and range shifting functions used together give you the means to select the depth you can see on screen. 4.4.1 Selecting the manual mode 1. 2. 3. 4. 4.4.2 If not displayed, press the [HIDE/SHOW] key to show the sounder soft keys. Press the AUTO/D. BOX soft key to show the auto mode window. Select OFF (MANUAL). Press the RETURN soft key.
4. VIDEO SOUNDER OPERATION Press the [GAIN] key to show the gain window, and rotate the [ENTER] knob to set the gain. Current level is shown on the bar. Press the RETURN key to finish. The setting range is 0-100. GAIN - HF ▲ 27 HIGH LOW ▼ Gain window Note 1: On the dual-frequency display, the gain can be independently set for LF and HF. Use the FREQ LF/HF soft key to select the frequency for which to adjust gain. Note 2: Gain cannot be adjusted in the automatic sounder mode.
4. VIDEO SOUNDER OPERATION 4.5 Measuring Depth, Time The VRM functions to measure the depth, and the time cursor measures time. 1. Rotate the [ENTER] knob to shift the VRM; counterclockwise the shift it downward, clockwise to shift it upward. You may also use the cursor pad to shift the VRM, in which case use ▲ or ▼. 2. Use ◄ or ► on the cursor pad to shift the cross-hair cursor to measure the elapsed time. Time to cursor intersection (Max. 99'59") Depth to VRM 0'33" 0 28.
4. VIDEO SOUNDER OPERATION 4.6 Reducing Interference Interference from other acoustic equipment operating nearby or other electronic equipment on your boat may show itself on the display as shown below. Interference from other sounder Electrical inteference Types of interference To reduce interference, do the following: 1. Press the [MENU] key. 2. Press the SOUNDER MENU soft key. 3. Select NOISE LIMITER and press the EDIT soft key to show the noise limiter window.
4. VIDEO SOUNDER OPERATION 4.7 Reducing Low Level Noise Dots (light-blue on the color model) may appear over most of the screen. This is mainly due to sediment in the water or noise. This noise can be suppressed by adjusting CLUTTER on the SOUNDER menu. Appearance of clutter When the sounder mode is Auto, the clutter suppression setting is fixed at AUTO. To reduce low level noise in manual sounder operation do the following: 1. Press the [MENU] key. 2. Press the SOUNDER MENU soft key. 3.
4. VIDEO SOUNDER OPERATION 4.8 Erasing Weak Echoes Sediment in the water or reflections from plankton may be painted on the display in green or light blue (color display) or “spots” on the background (monochrome display). These weak echoes may be erased as below. Weak echoes Appearance of weak echoes 1. Press the [MENU] key. 2. Press the SOUNDER MENU soft key. 3. Select SIGNAL LEVEL, and press the EDIT soft key to show the signal level window.
4. VIDEO SOUNDER OPERATION 4.9 White Marker (GD-1700C/1710C) The white marker functions to display a particular echo color in white. For example, you may want to display the bottom echo in white to discriminate fish echoes near the bottom. 1. Press the [MENU] key. 2. Press the SOUNDER MENU soft key. 3. Select WHITE MARKER, and press the EDIT soft key to open the white marker window. WHITE MARKER ▲ OFF ▼ White marker window 4. Use the cursor pad to select color to display in white.
4. VIDEO SOUNDER OPERATION 4.10 Picture Advance Speed The picture advance speed determines how quickly the vertical scan lines run across the screen. When selecting a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will contract it. The advancement speed may be set independent of or synchronized with ship’s speed. 4.10.1 Advancement independent of ship’s speed 1. Press the [MENU] key. 2.
4. VIDEO SOUNDER OPERATION 4.10.2 Advancement synchronized with ship’s speed With speed data provided by a speed measuring device, picture advance speed may be automatically synchronized with ship’s speed. As shown in the figure below the horizontal scale of the display is not influenced with the speed dependent picture advance mode active, thus it permits judgment of fish school size and abundance at any speed. Fish school shrinks as speed is increased; expanded as speed is decreased.
4. VIDEO SOUNDER OPERATION 4.11 Display Colors (GD-1700C/1710C) You can select the number of colors and background color to display as follows: 1. Press the [MENU] key. 2. Press the SOUNDER MENU soft key. 3. Select HUE, and then press the EDIT soft key to show the hue window. HUE ▲ 1 ▼ Hue window 4. Use the cursor pad to select hue number, referring to the table below. (You can see the result of your selection on the display.) Hue no. and background and echo colors Hue No.
4. VIDEO SOUNDER OPERATION 4.12 Alarms The sounder section has five conditions which generate visual and aural alarms: bottom alarm, fish alarm (bottom lock), fish alarm (normal) and water temperature alarm (temperature sensor required). For 1700C/1710C, note that the alarm icon is red when an alarm setting is violated, and changes to background color when the [CLEAR] key or CLEAR ALARM soft key is pressed. The color does not change when another alarm is violated.
4. VIDEO SOUNDER OPERATION 4.12.2 Bottom alarm The bottom alarm sounds when the bottom echo is within the alarm range set. To activate the bottom alarm the depth must be displayed. Note that the bottom alarm is turned on or off reciprocally with the bottom alarm on the plotter alarm menu. 1. Press the [ALARM] key to show the ALARM menu. 2. Use the cursor pad to select BOTTOM ALARM. 3. Press the EDIT soft key to show the bottom alarm window. BOTTOM ALARM ▲ ¡ ON 0000.0-0000.
4. VIDEO SOUNDER OPERATION 4.12.4 Fish alarm (B/L) The bottom-lock fish alarm sounds when a fish echo is within a predetermined distance from the bottom. Note that the sensitivity of the fish alarm can be set on the SOUNDER SYSTEM SETUP menu. 1. Press the [ALARM] key to show the ALARM menu. 2. Use the cursor pad to select FISH ALARM (B/L). 3. Press the EDIT soft key to show the fish alarm (B/L) window. FISH ALARM (B/L) ▲ ¡ ON 0000.0-0000.0 ft ¤ OFF ▼ Fish alarm (B/L) window 4.
4. VIDEO SOUNDER OPERATION 4.12.5 Water temperature alarm There are two types of water temperature alarms: WITHIN RANGE and OUT OF RANGE. The WITHIN RANGE alarm sounds when the water temperature is within the range set, the OUT OF RANGE alarm sounds when the water temperature is higher or lower than the range set. This alarm requires water temperature data. Note that the water temperature alarm is turned on or off reciprocally with the water temperature alarm on the plotter alarm menu. 1.
4. VIDEO SOUNDER OPERATION 4.12.6 When an alarm setting is violated... When an alarm setting has been violated the buzzer sounds and the speaker icon appears (in red on the color model). Press the [CLEAR] key to silence the alarm. For color models, press the [ALARM] key, CLEAR ALARM soft key to change the speaker icon from red to black. You can see which alarm has been violated on the alarm menu display. In the example below the fish alarm has been violated. To see which alarm(s) has been violated; 1.
4. VIDEO SOUNDER OPERATION Alarm messages The table below shows the sounder alarm messages and their meanings Sounder alarm messages and their meanings Message DEPTH ALARM! FISH ALARM! TEMPERATURE ALARM! 4.13 Meaning Bottom alarm violated. Fish alarm violated. Water temperature alarm violated. Water Temperature Graph The water temperature graph (appropriate sensor required) plots water temperature on the sounder display. (See the figure on page 4-3.) It can be turned on or off as below. 1. 2. 3. 4. 5.
4. VIDEO SOUNDER OPERATION 4.15 Interpreting the Sounder Display 4.15.1 Zero line The zero line (sometimes referred to as the transmission line) represents the transducer’s position. Zero line Shift Zero line 4.15.2 Bottom echo Echoes from the bottom are normally the strongest and are displayed in reddish-brown (color model) or darkest tone (monochrome model) but the color (tone on the monochrome model) and width will vary with bottom composition, water depth, frequency, sensitivity, etc.
4. VIDEO SOUNDER OPERATION 4.15.3 Fish school echoes Fish school echoes will generally be plotted between the zero line and the bottom. Usually the fish school/fish echo is weaker than the bottom echo because its reflection property is much smaller compared to the bottom. The size of the fish school can be ascertained from the density of the display. Size of fish school Small school Large school Fish school echoes 4.15.
5. CUSTOMIZING YOUR UNIT This chapter describes the various options which allow you to set up your unit to suit your needs. For mode-specific menus, e.g. radar, plotter and sounder, make sure that you select the appropriate display when making changes or viewing menu options. 5.1 General Setup This paragraph shows you how to set up functions common to the plotter, radar and sounder displays. This is done on the GENERAL SETUP menu, which you may display from any mode.
5. CUSTOMIZING YOUR UNIT Contents of general setup menu Item Description Key Beep Turns key beep on/off. On, Off Language Chooses menu language. English, French, German, Italian, Portuguese, Spanish Range Unit Chooses unit of range and speed measurement. nm, kt; km, km/h; sm, mph; nm & yd, kt; nm & m, kt; km & m, km/h; sm & yd, mph Temperature Unit Chooses unit of water temperature measurement. °C,°F Depth Unit Chooses unit of depth measurement.
5. CUSTOMIZING YOUR UNIT Contents of general setup menu (con’t from previous page) Item Description Settings Range & Bearing Mode Chooses how to calculate range and bearing. Rhumb Line: Straight line drawn between two points on a nautical chart. Great Circle: Shortest course between two points on the surface of the earth. Bearing Readout Chooses bearing display format for course, course over ground and cursor bearing.
5. CUSTOMIZING YOUR UNIT 5.2 Plotter Setup This paragraph provides the information necessary for setting up the plotter display. 5.2.1 Navigation options Navigation options, for example, waypoint switching method, may be set on the PLOTTER SETUP menu. 1. Show the plotter display, then press the [MENU] key open the main menu. 2. Press the PLOTTER SETUP soft key. WAYPOINT SWITCHING ARRVL ALM CRCL COURSE VECTOR LINE SET GOTO METHOD 1POINT QP INTERNAL PLOTTER SETUP EDIT D.
5. CUSTOMIZING YOUR UNIT Function key setup The function keys provide one-touch execution of a desired function. The default plotter function key settings are as shown in the table below. Function Key 1 2 3 4 5 Start/stop recording/plotting own ship’s track. Edit mark/line. Ruler (measure range and bearing between two points). Function Key Label TRK EML RUL Add new waypoint. Alphanumeric waypoint list.
5. CUSTOMIZING YOUR UNIT 4. Select function desired with the cursor pad or [ENTER] knob, then press the ENTER soft key or [ENTER] knob to register your selection. 5. Press the [MENU] key to close the menu. Plotter function keys Menu Item Function Function Key Label OFF Assigns no function. — ADD: ADD NEW WPT Registers waypoint at cursor position. Place cursor for waypoint location, then press function key. ADD MWP: MOVE WPT Moves selected waypoint to different position.
5. CUSTOMIZING YOUR UNIT 5.3 Chart Setup This paragraph shows you how to setup digital charts, from offsetting chart position to turning chart attributes on or off. 5.3.1 Chart offset In some instances position may be off by a few seconds. For example, the position of the ship is shown to be at sea while it is in fact moored at a pier. You can compensate for this error by offsetting chart position as shown in the procedure below. 1.
5. CUSTOMIZING YOUR UNIT 5.3.2 FURUNO, NavCharts™ chart attributes FURUNO, NavCharts™ chart attributes may be turned on or off from the CHART DETAILS menu, which you may display as follows: 1. Press the [MENU] key. 2. Press the CHART SETUP and CHART DETAILS soft keys.
5.
5. CUSTOMIZING YOUR UNIT CNTOUR LINE soft key 1. Press the [MENU] key. 2. Press the CHART SETUP and CHART DETAILS soft keys. 3. Press the CNTOUR LINE soft key. DEPTH < 10m RED DEPTH = 10m YELLOW DEPTH > 10m LIGHT BLUE DEPTH INFORMATION RED CNTOUR LINE EDIT 10m = APPROX. 30ft OR 5fa OR 6pb DEPTH < 10m ON DEPTH = 10m ON DEPTH > 10m ON DEPTH INFORMATION ON RETURN GD-1700 Contour line menu (FURUNO, NavCharts™) 5-10 EDIT 10m = APPROX.
5. CUSTOMIZING YOUR UNIT 5.3.3 C-MAP chart attributes C-MAP chart attributes may be turned on or off from the CHART DETAILS menu as follows: 1. Press the [MENU] key. 2. Press the CHART SETUP and CHART DETAILS soft keys.
5.
5.
5. CUSTOMIZING YOUR UNIT Settings description Basic: Shows basic characteristics of objects. Detailed: Shows detailed characteristics of objects. Multiple: Shows multiple icons for complex objects. Off: Turns item off. On: Turns item on. Plotter: Shows item on plotter display. Plotter/Contour: Shows contour on plotter display. Plotter/Overlay: Shows item on plotter and overlay displays. Plot/No Sector: Shows item on plotter display. Sector not shown. Single: Shows single icon for complex objects.
5. CUSTOMIZING YOUR UNIT 5.4 Data Boxes Setup You may select the data to show in the data boxes for the plotter, radar and sounder displays. Six boxes may be displayed in case of small size data box and two for large size data box. 1. Display the plotter, radar or sounder display, whichever you want to set. 2. Press the [MENU] key to open the main menu. 3. Press one of the following sets of soft keys depending on the display selected at step 1. a) Plotter mode: PLOTTER SETUP, D.
5. CUSTOMIZING YOUR UNIT 5.5 Hot Page Setup Five user-arrangeable hot pages are provided for quick selection of desired display. 1. Press the [MENU] key followed by pressing the SYSTEM CONFIGURATION, SYSTEM SETUP, HOT PAGE & NAV DISP SETUP and HOT PAGE SETUP soft keys in that order. HOT PAGE 1 HOT PAGE 2 HOT PAGE 3 HOT PAGE 4 HOT PAGE 5 Hot page setup menu 2. Use the cursor pad to select the hot page number to set, then press the EDIT soft key. The full-screen selection window appears.
5. CUSTOMIZING YOUR UNIT 3. Rotate the [ENTER] knob to select the full-screen picture desired and push the [ENTER] knob. A set of combination screens, corresponding to the full-screen selected, appears. HOT PAGE 1 10 20 ----- Combination screen selection window 4. Rotate the [ENTER] knob to select the full screen or combination screen desired and push it to set. 5.6 Navigator Setup This section provides the information necessary for selecting the type of navigator connected to your plotter. 5.6.
5. CUSTOMIZING YOUR UNIT Contents of nav setup menu Item Position Source Description Chooses source of position data. Speed Averaging Calculation of ETA is based on average ship’s speed over a given period. If the period is too long or too short, calculation error will result. Change this setting if the ETA seems wrong. GPS uses UTC time. If you would rather use local time, enter the time difference between it and UTC. Use the +<-->- soft key to switch from plus to minus and vice versa.
5. CUSTOMIZING YOUR UNIT Contents of GPS setup menu Item Local Time Offset Geodetic Datum Position Smoothing Spd/Cse Smoothing Description GPS uses UTC time. If you would rather use local time, enter the time difference between it and UTC. Use the +< - ->- soft key to switch from plus to minus and vice versa. Geodetic datum is a reference for geodetic survey measurements consisting of fixed latitude, longitude and azimuth values associated with a defined station of reference.
5. CUSTOMIZING YOUR UNIT Contents of GPS sensor settings menu (con’t from previous page) Item Description Settings GPS Speed Averaging Calculation of ETA is based on average ship’s speed over a given period. If the period is too long or too short, calculation error will result. Change this setting if calculation error occurs. The default setting is suitable for most conditions. 0-999 seconds Latitude, Longitude Offset Offsets latitude position to In addition, refine position accuracy.
5. CUSTOMIZING YOUR UNIT WAAS SETUP Press the WAAS SETUP soft key to show the WAAS SETUP display. Note: This function requires GP-320B antenna. Also, confirm that your display unit has the program version no. shown below. NavChart type: Ver.12 and after (1710C: Ver.4 and after) C-map type: Ver.8 and after (1710C: Ver.4 and after) Contents of WAAS SETUP menu Item Description Settings WAAS MODE Select ON to use the WAAS mode.
5. CUSTOMIZING YOUR UNIT 5.6.3 TD display setup The TD SETUP menu sets which Loran C or Decca chain to use to display TD position. (Connection of a Loran C or Decca navigator is not necessary to display TD position.) 1. Press the [MENU] key. 2. Press the SYSTEM CONFIGURATION, NAV OPTION and TD SETUP soft keys to display the TD SETUP menu. TD LORAN-C SETUP GRI 9940:11-27 U.S. WEST COAST CORRECTION 1 +000.0 µs CORRECTION 2 +000.0 µs DECCA CHAIN 01 R-G S BALTIC CORRECTION 1 +00.00 lane CORRECTION 2 +00.
5. CUSTOMIZING YOUR UNIT 6. If necessary, you may enter a position offset to refine Loran C position accuracy. Select (GRI) CORRECTION 1 or CORRECTION 2, then press the EDIT soft key. Enter correction value with the cursor pad and [ENTER] knob, then press the ENTER soft key or the [ENTER] knob. Use the +<− −>- soft key to switch from plus to minus and vice versa. 7. Press the RETURN soft key twice. 8. Press the GENERAL SETUP soft key followed by the NEXT PAGE soft key. 9.
5. CUSTOMIZING YOUR UNIT 5.7 Nav Data Display Setup The nav data display shows various navigation data, fed from a navigator, network equipment, etc. You may select the data to display and where to display it as follows: 1. Press the [MENU] key to open the main menu. 2. Press the SYSTEM CONFIGURATION, SYSTEM SETUP, HOT PAGE & NAV DISP SETUP and NAV DATA DISPLAY SETUP soft keys.
5. CUSTOMIZING YOUR UNIT 5.8 Radar Setup This paragraph explains how to customize the radar display to suit your operational needs. Note: The RADAR RANGE SETUP soft key is inoperative. 5.8.1 Radar display setup The radar display may be set up from the RADAR DISPLAY SETUP menu, which contains items such as EBL reference and cursor position format. 1. Press the [MENU] key to show the main menu. 2. Press the RADAR DISPLAY SETUP soft key.
5. CUSTOMIZING YOUR UNIT Contents of radar display setup menu Item EBL Reference Cursor Position Tuning TX Sector Blanking Noise Rejection Description Settings References EBL bearing, shown in the True, Relative EBL data box, to North (True) or heading (Relative). Relative with no heading input. True only in course-up, north-up and true motion. Chooses how to display cursor position. LAT/LON: Lat/Long position TD: Loran C or Decca Note: “RNG & BRG-TRUE” requires TDs heading data and true bearing..
5. CUSTOMIZING YOUR UNIT Contents of radar display setup menu (con’t from previous page) Item Description Settings Background Color (GD-1700C,GD-1710C) Chooses colors of background, range rings and characters. Effective when HUE soft key is set for “MANUAL.
5. CUSTOMIZING YOUR UNIT 5.8.2 Function key setup The function keys provide one-touch execution of a desired function. The default radar function key settings are as shown in the table below. Function Key 1 Default Function Turn heading line off. Function Key Label HL 2 3 4 Turn range rings on/off. Turn echo trail on/off. Turn display offcenter on/off. RNG TRL OFC 5 STBY/TX TX If the above settings are not to your liking you may change them as follows: 1. Press the [MENU] key. 2.
5. CUSTOMIZING YOUR UNIT 4. Select function desired with the cursor pad, then press the ENTER soft key or [ENTER] knob to register your selection. 5. Press the [MENU] key to close the menu. Radar function keys Menu Item Function Function Key Label OFF Assigns no function. — HL: HDG LINE OFF Turns heading line off. HL MOD: MODE Selects presentation mode. GAI: GAIN Shows gain sensitivity adjustment window. GAI SEA: A/C SEA Shows A/C SEA adjustment window.
5. CUSTOMIZING YOUR UNIT 5.9 Sounder Setup This section shows you how to customize your network sounder to your liking. You can set fish alarm sensitivity, fine tune sensor data, etc. 5.9.1 System setup 1. Show the sounder display, then press the [MENU] key. 2. Press the SOUNDER SYSTEM SETUP soft key.
5. CUSTOMIZING YOUR UNIT Sounder system setup menu description (con’t from previous page) Item Description Settings TVG (LF, HF) TVG (Time Varied Gain) compensates for propagation attenuation of the ultrasonic waves. It does this by equalizing echo presentation so that fish schools of the same size appear in the same density in both shallow and deep waters. In addition, it reduces surface noise. Note that if the TVG level is set too high short range echoes may not be displayed.
5. CUSTOMIZING YOUR UNIT 5.9.2 Sensor setup The SENSOR SETUP menu lets you further refine speed, water temperature and depth data fed from the network sounder. 1. Show the sounder display, then press the [MENU] key. 2. Press the SOUNDER SYSTEM SETUP and SENSOR SETUP soft keys to show the SENSOR SETUP menu. The current ship’s speed, water temperature, depth and speed of sound are shown at the bottom of the menu. SPEED CALIBRATION + 00% TEMP CALIBRATION + 0°F DEPTH CALIBRATION +0.
5. CUSTOMIZING YOUR UNIT 5.9.3 Sounding range, zoom range, bottom lock range This paragraph shows you how to set custom ranges for basic range, zoom range (marker and bottom zoom) and bottom lock range. All default basic ranges are restored whenever the unit of depth measurement is changed. Therefore, change the depth unit before changing the basic ranges. 1. Show the sounder display, then press the [MENU] key to open the main menu. 2.
5. CUSTOMIZING YOUR UNIT 5.9.4 Function key setup The function keys, shown when the soft keys are turned off, provide one-touch execution of a desired function. The default sounder function key settings are as shown in the table below. Function Key 1 2 3 4 5 Default Function Output current position. Suppress clutter. Erase weak signal. Suppress noise. Set picture advancement speed. Function Key Label TLL CLT SLV NL PA If the above settings are not to your liking you may change them as follows: 1.
5. CUSTOMIZING YOUR UNIT 5. Select function desired with the cursor pad. 6. Press the ENTER soft key or the [ENTER] knob to register your selection. 7. Press the [MENU] key to close the menu. Sounder function keys Menu Item Function Function Key Label OFF Assigns no function. MOD: AUTO MODE Display automatic mode selection window. MOD GHF: GAIN - HF Displays high frequency gain adjustment window. GHF GLF: GAIN - LF Displays low frequency gain adjustment window.
5. CUSTOMIZING YOUR UNIT This page is intentionally left blank.
6. DATA TRANSFER 6. DATA TRANSFER This chapter provides information for saving and replaying data to and from memory cards, uploading and downloading data, loading waypoint data from Yeoman, and outputting data through the network. Note: The data transfer function is not available for the optional memory card interface unit CU-200. 6.1 Memory Card Operations The memory cards store these data: marks, lines, waypoints, routes, track, and setting data. 6.1.
6. DATA TRANSFER 6.1.2 Saving data to a memory card 1. Insert a formatted memory card into the slot. 2. Press the [MENU] key followed by the CONFIGURATION, DATA TRANSFER, UPLOAD/DOWNLOAD DATA and SAVE DATA TO MEMORY CARD soft keys to show the SAVE DATA menu. ▲ TRACKS OFF MARKS & LINES OFF WAYPOINTS & ROUTES OFF SETTING DATA* OFF SAVE DATA EDIT SAVE FORMAT RETURN * = Plotter data only Save data menu 3. 4. 5. 6. 7. 8. Use the cursor pad to select item to save. Press the EDIT soft key.
6. DATA TRANSFER Memory card messages Various memory card messages appear to alert you to memory card-related error. These are tabulated below. Memory card messages Message Reason Remedy Memory card is not inserted. Please insert memory card. Push ENTER knob to continue. Memory card not inserted. Push the [ENTER] knob to return to the SAVE DATA display and then insert card. Memory card is not formatted. Push ENTER knob to continue. Unformatted memory card.
6. DATA TRANSFER 6.1.3 Playing back data from a memory card Data (marks, lines, track, waypoints, routes and setting data) can be loaded from a memory card and displayed on the screen. This feature is useful for observing past data and setting up the equipment for a specific purpose with “setting data.” 1. Press the [MENU] key followed by the SYSTEM CONFIGURATION and DATA TRANSFER soft keys. 2. Press the UPLOAD/DOWNLOAD DATA soft key. 3.
6. DATA TRANSFER 6.2 Uploading, Downloading Data You can upload/download waypoints, routes, marks and lines from/to a PC, through the DATA 3 port at the rear of the display unit. Note that radar and sounder data cannot be uploaded or downloaded. 6.2.
6. DATA TRANSFER 7. To change the baud rate, press the SELECT BPS soft key. BAUD RATE ▲ ¤ ¡ ¡ 4800 bps 9600 bps 19200 bps ▼ Baud rate window 8. Select baud rate, then press the ENTER soft key. 9. Press the DWLOAD or UPLOAD soft key. You are asked if you are ready to download or upload waypoints and routes. 10. Push the [ENTER] knob to download or upload data. Waypoint data format PFEC, GPwpl, llll.llll, a, yyyyy.
6. DATA TRANSFER Route data menu $PFEC, GPrtc, xx, c----c 1 2 Route data format 1: Number of sentences required for one complete route data (1 to 4). See Note 2. 2: Number of sentences currently used (1 to 4) 3: Message mode (Always set to C) 4: Route No. (001 to 300, 3 digits required) 5 through 12: Waypoint name (Max. 8 names, length of each waypoint name is fixed to 7 byte) Note 2: A route can may contain 35 waypoints, and the GPRTE sentence for one route data may exceed 80 byte limitation.
6. DATA TRANSFER 6.3 Loading Waypoint Data from Yeoman Waypoint data can be loaded from a Yeoman to this equipment. Connect the Yeoman to any DATA port on this equipment and then follow the procedure below. 1. 2. 3. 4. 5. Press the [MENU] key. Press the SYSTEM CONFIGURATION key. Press the DATA TRANSFER soft key. Press the RECEIVE YEOMAN DATA soft key. You are asked if you are sure to receive waypoint data from Yeoman equipment. Push the [ENTER] knob to receive the data.
6. DATA TRANSFER 6.4 Receiving Data Via Network Equipment You can receive waypoints, routes, marks and lines from NavNet equipment. 1. 2. 3. 4. Press the [MENU] key. Press the SYSTEM CONFIGURATION soft key. Press the DATA TRANSFER soft key. Press the RECEIVE DATA VIA NETWORK soft key. HOST NAME PLOT1 - - MARKS & LINES OFF WAYPOINTS & ROUTES OFF RECEIVE DATA EDIT RCV RETURN Receive data menu 5. Select HOST NAME, then press the EDIT soft key. HOST NAME PLOT1--- Host name window 6.
6. DATA TRANSFER 10. Press the RCV soft key followed by the [ENTER] knob. The message “NOW RECEIVING DATA.” is displayed. If no data could be found, the message “(HOST NAME)’ IS NOT FOUND.” appears. 11. When the transfer is completed, the message “DATA TRANSFER COMPLETED. PUSH ENTER KNOB TO CONTINUE.” appears. Push the [ENTER] knob. 12. Press the [MENU] key to close the menu. 6.5 Outputting Data Through the Network Follow the procedure below to output data through the network. 1.
7. MAINTENANCE, TROUBLESHOOTING This chapter provides information necessary for keeping your unit in good working order and remedying simple problems. WARNING Do not open the equipment. Hazardous voltage which can cause electrical shock exists inside the equipment. Only qualified personnel should work inside the equipment. 7.1 Preventive Maintenance Regular maintenance is important for optimum performance.
7. MAINTENANCE, TROUBLESHOOTING 7.2 Replacement of Fuse The fuse on the power cable protects the equipment from reverse polarity of the ship’s mains and equipment fault. If the fuse blows, find out the cause before replacing it. Use the correct fuse (10A for 12 V, 5A for 24 V). Using the wrong fuse will damage the equipment and void the warranty. CAUTION Use the proper fuse. Use of a wrong fuse can cause fire or damage the equipment. 7.
7. MAINTENANCE, TROUBLESHOOTING 7.4 Simple Troubleshooting This section provides simple troubleshooting procedures which the user can follow to restore normal operation. If you cannot restore normal operation do not attempt to check inside the unit. Any trouble should be referred to a qualified technician. 7.4.1 General General troubleshooting If… you cannot turn on the power Then… • check for blown fuse. • check that the power connector is firmly fastened.
7. MAINTENANCE, TROUBLESHOOTING 7.4.3 Radar Requires a network radar. Radar troubleshooting If… But… you pressed the [POWER/BRILL] key and the RADAR soft key to show the radar picture picture does not appear marks, legends appear no echo appears the picture is not updated or it freezes Then… • check that the antenna cable is firmly fastened. • check that radar source is correct. — • check Tx fuse in the power cable. If it is blown, replace it. • check antenna cable.
7. MAINTENANCE, TROUBLESHOOTING 7.4.4 Sounder Requires Network Sounder ETR-6/10N, ETR-30N. Sounder troubleshooting If… you selected a sounder display with the DISP key But… no sounder display appears Then… • check that the network sounder’s signal cable is firmly fastened. • check that the network sounder is plugged in. The LED of the network sounder should flash every second. • check that sounder source is correct.
7. MAINTENANCE, TROUBLESHOOTING 7.5 Diagnostics This paragraph provides the procedures for testing the equipment for proper operation. Four tests are provided: Memory I/O test, Keyboard test, Remote controller test, and Test pattern. 7.5.1 Memory I/O test The memory I/O test provides for individual testing of the display unit, GPS Receiver GP-310B/320B, Network Sounder ETR-6/10N, ETR-30N and ARP, displaying program number and checking for proper operation. 1. 2. 3. 4. 5.
7. MAINTENANCE, TROUBLESHOOTING Display unit test Press the DISPLAY UNIT TEST soft key at the MEMORY I/O TEST menu to test the display unit. The equipment displays program version number and checks devices. Results for device checks are shown as OK or NG (No Good). For any NG, request service. A test connector is required to check ports. “ - - “ shown when no test connector is connected. Chart number shown for C-MAP cards only. Press the RETURN soft key to return the MEMORY I/O TEST menu. PROGRAM No.
7. MAINTENANCE, TROUBLESHOOTING Network sounder test (Requires Network Sounder ETR-6/10N, ETR-30N) Press the NETWORK SOUNDER TEST soft key at the MEMORY I/O TEST menu to test the Network Sounder ETR-6/10N or ETR-30N. The equipment displays network sounder program version number, checks the ROM and RAM, and displays water temperature (appropriate sensor required) and depth. The results of the ROM and RAM check are shown as OK or NG (No Good). For any NG, request service.
7. MAINTENANCE, TROUBLESHOOTING 7.5.2 Test pattern The test pattern test checks the display for proper display of colors (GD-1700C/1710C) or tones (GD-1700). 1. 2. 3. 4. 5. Press the [MENU] key to show the menu. Press the SYSTEM CONFIGURATION soft key. Press the SYSTEM SETUP soft key. Press the TEST & CLEAR soft key. Press the TEST PATTERN soft key to show the test pattern. BLACK BLUE GREEN GREEN RED RETURN WHITE RETURN RETURN PRESS ENTER KNOB TO CHANGE PATTERN.
7. MAINTENANCE, TROUBLESHOOTING 7.5.3 Keyboard, remote controller test The keyboard test checks the controls on the display unit and remote controller for proper operation. 1. 2. 3. 4. 5. Press the [MENU] key to show the menu. Press the SYSTEM CONFIGURATION soft key. Press the SYSTEM SETUP soft key. Press the TEST & CLEAR soft key. Press the KEYBOARD & REMOTE TEST soft key.
7. MAINTENANCE, TROUBLESHOOTING 7.6 GPS Status Display The GPS status display provides data about the GPS satellites. It is available with connection of the GPS Receiver GP-310B/320B or a GPS navigator outputting the data sentence GSA or GSV. 1. Press the [MENU] key. 2. Press the SYSTEM CONFIGURATION, NAV OPTION and GPS SENSOR SETTINGS soft keys to display the GPS SENSOR SETTINGS menu. 3. Press the GPS STATUS soft key. 4. Press the RETURN soft key to quit the GPS status display.
7. MAINTENANCE, TROUBLESHOOTING 7.7 Clearing Memories Your equipment has a memory for each of the plotter, radar and sounder sections. These memories can be cleared to start operation with default settings. The following data are not cleared: Heading adjustment, timing adjustment, MBS level, tuning point, tuning indication (short, medium, long), video level, dead sector, antenna height, STC curve, antenna type, on time, tx time. 1. 2. 3. 4. 5. Press the [MENU] key to open the menu.
7. MAINTENANCE, TROUBLESHOOTING 7.8 Error Messages In addition to alarm messages your equipment also displays error messages. Error messages Error Message Meaning Connection with the ETR was cut. Network sounder disconnected. Connection with the RADAR was cut. Radar disconnected. Low Voltage! Internal Battery Voltage of battery on circuit board in display unit is low. No bearing pulse detected. No bearing pulse from radar antenna. Check antenna cable.
7. MAINTENANCE, TROUBLESHOOTING This page is intentionally left blank.
APPENDIX Menu Overview MENU key Plotter CHART SETUP MENU Key CHART OFFSET (offsets chart position.) TRACKS & OWN SHIP TRACK DISP (ON, OFF) MARKS OWN SHIP TRACK COLOR (RED, YELLOW, GREEN, LIGHT BLUE, PURPLE, BLUE, WHITE)* CONTROL TARGET TRACK DISPLAY (ON, OFF) TARGET TRACK COLOR (RED, YELLOW, GREEN , LIGHT BLUE, PURPLE, BLUE, WHITE)* INTERVAL (TIME, DISTANCE) TIME INTERVAL (0 - 99m59s, 10 seconds) DISTANCE INTERVAL (0 - 99.99nm/km/sm, 0.
APPENDIX 2 1 Page 1 CHART DETAILS WAYPOINT O (N,PLOTTER/OVERLAY*, PLOTTER* , OFF) WAYPOINT NAME O (N,PLOTTER/OVERLAY*, PLOTTER* , OFF) (C-MAP LAT/LON GRID ON, ( PLOTTER/OVERLAY*, PLOTTER* , OFF) chart) CHART BORDER LINEON, ( PLOTTER/OVERLAY*, PLOTTER* , OFF) BACKGROUND (WHITE, BLACK) PORT & SERVICEON, ( PLOTTER/OVERLAY*, PLOTTER* , OFF) ATTENTION AREA(ON,PLOTTER/OVERLAY*, PLOTTER* , PLOTTER CONTOUR*, OFF) NAV LANE ( ON,PLOTTER/OVERLAY*, PLOTTER* , OFF) * = Denotes GD-1700C/1710C only.
APPENDIX 3 SYSTEM GENERAL KEY BEEPON, ( OFF) CONFIGURATION SETUP LANGUAGE ( ENGLISH, OTHERS) RANGE UNIT Page 1 (nm, kt; km, km/h; sm, mph; nm&yd, kt; nm&m, kt; km&m, km/h; sm&yd, m TEMPERATURE UNIT°F, ( °C) DEPTH UNIT (m, ft, fa, pb) TEMPERATURE SOURCE ETR, ( NMEA) DEPTH SOURCE ETR, ( NMEA) RESET TRIP LOG (YES, NO) SPEED SOURCE (ETR, NMEA) LAT/LON DISPLAY (DD ° MM. MM', DD ° MM. MMM',DD° MM. MMMM', DD° MM' SS.
APPENDIX 4 PORT SETUP SYSTEM SETUP GPS/NMEA FURUNO GPS SENSOR PORT (YES, NO) OUTPUT FORMAT (NMEA 0183 Ver.1.5, 2.0) LAT/LON FORMAT (DD° MM. MM' DD° MM. MMM' DD° MM. MMMM') OUTPUT DESTINATION (YES, NO) SELECT SNTNC soft key* NMEA PORT FURUNO GPS SENSOR (YES, NO) OUTPUT FORMAT (NMEA 0183 Ver.1.5, 2.0) LAT/LON FORMAT (DD° MM. MM' DD° MM. MMM' DD° MM. MMMM') OUTPUT DESTINATION (YES, NO) SELECT SNTNC soft key* PC/NMEA/ OUTPUT FORMAT EXT. BUZZ (NMEA 0183 Ver.1.5, 2.
APPENDIX 5 MEMORY I/O TEST TEST & CLEAR DISPLAY UNIT TEST GPS SENSOR TEST* NETWORK SOUNDER TEST** ARP TEST*** KEYBOARD & REMOTE TEST (Tests keyboard and remote controller.) TEST PATTERN (Displays test pattern.) MEMORY CLEAR DISPLAY UNIT (YES, NO) GPS SENSOR (YES, NO)* NETWORK SOUNDER (YES, NO)** HOT PAGE HOT PAGE SETUP & NAV DISP (Sets up hot pages 1-5.) SETUP NAV DATA DISPLAY SETUP (Configures nav data displays.
APPENDIX Radar MENU Key RADAR EBL REFERENCE (TRUE, RELATIVE) DISPLAY SETUP CURSOR POSITION (LAT/LON, RNG&BRG-REL, TD, RNG&BRG-TRUE) TUNING AUTO, ( MAN) TX SECTOR BLANKING (ON (FROM°, 0.0SECTOR 001 °)), OFF) NOISE REJECTION OFF, ( LOW, HIGH) BACKGROUND COLOR B (LACK/GREEN, BLACK/RED, BLUE/WHITE, DARK BLUE/WHITE, WHITE/GREEN)* ECHO COLOR (YELLOW, GREEN, MULTI-COLOR)* * = GD-1700C/1710C only. WATCHMAN TIME ( 5, 10, 20 (minutes)) RANGE UNITnm, ( km, sm) D. BOX soft key (Same items as on plotter menu.
APPENDIX Sounder MENU Key SOUNDER NOISE LIMITER (OFF, LOW, MEDIUM, HIGH) * = GD-1700C/1710C only MENU CLUTTER (0-16, AUTO) WHITE MARKER (1-8 (8 color), 1-16 (16 color), OFF)* ZOOM MARKER (ON, OFF) SL1-SL2: Monochrome SL1-SL3: 8 color SL1-SL6: 16 color HUE (1-9, 1)* SIGNAL LEVEL (OFF, SL1, SL2, SL3, SL4, SL5, SL6) PICTURE ADVANCE (2/1, 1/1, 1/2, 1/4, 1/8, 1/16, STOP) TEMPERATURE GRAPH (ON, OFF) PRR LEVEL (0-20, SPD SENSING PRR, 20) D. BOX soft key (Same items as on plotter menu. See page A-2.
APPENDIX ALARM key Radar Alarms ALARM key SET GUARD 1 (ERASE GUARD 1) SET GUARD 2 (ERASE GUARD 2) Plotter Alarms ALARM key AUDIO ALARM (INT & EXT BUZZ, INTERNAL BUZZ, OFF) ARRIVAL ALARM (ON, OFF, default range: 0.010 nm(km/sm)) ANCHOR WATCH ALARM (ON, OFF, default range: 0.010 nm(km/sm)) PROXIMITY ALARM (ON, OFF) XTE ALARM (ON, OFF, default range: 0.
APPENDIX Geodetic Chart List 001: WGS84 002: WGS72 003: TOKYO : Mean Value (Japan, Korea, and Okinawa) 004: NORTH AMERICAN 1927 : Mean Value (CONUS) 005: EUROPEAN 1950 : Mean Value 006: AUSTRALIAN GEODETIC 1984 : Australia and Tasmania Island 007: ADINDAN : Mean Value (Ethiopia and Sudan) 008: : Ethiopia 009: : Mall 010: : Senegal 011: : Sudan 012: AFG : Somalia 013: AIN EL ABD 1970 : Bahrain Island 014: ANNA 1 ASTRO 1965 : Cocos Island 015: ARC 1950 : Mean Value 016: : Botswana 017: : Lesotho 018: : Malaw
APPENDIX World Time Chart A-10
APPENDIX Icons Icon Meaning North marker. Points to North. Correct chart and suitable scale - full chart reliability. Chart overenlarged. • Chart card not inserted. • Wrong chart card inserted. • Chart scale too small. Plotter, radar, sounder alarm setting violated. Track is not being recorded or plotted. Chart offset applied. SA VE Voyage-based route is being created. Latitude and longitude position offset applied. Voltage of battery on circuit board in display unit is low.
APPENDIX This page is intentionally left blank.
SPECIFICATIONS VIDEO PLOTTER GD-1700 COLOR VIDEO PLOTTER GD-1700C/1710C 1 DISPLAY UNIT 1.1 Indication System 1.2 1.
2.9. MOB 1 point 2.10. Quick Routes 1 course with 35 waypoints max. 2.11. Electronic Chart FURUNO chart card or NAVIONICS chart card available C-MAP chart card also available for C-MAP NT Model 2.12. Alarms Arrival and Anchor watch, Cross track error and proximity alarms, Ship’s speed in and out alarms, Water temperature, Bottom alarm, Trip alarm, Fish alarm (ETR required) 3 POWER SUPPLY 3.1 Rated Voltage/Current GD-1700: 12-24 VDC: 1.4-0.7 A GD-1700C: 12-24 VDC: 1.7-0.
INDEX A A/C RAIN...................................................... 3-5 A/C SEA ....................................................... 3-4 ACQ soft key............................................... 3-35 ALARM key plotter ..................................................... 2-53 radar....................................................... 3-30 sounder .................................................. 4-20 Alarms anchor watch .......................................... 2-55 arrival......................
INDEX Colors (GD-1700C/1710C) EBL soft key.................................................. 3-15 echoes (radar) ..........................................5-27 EBL/VRM key ................... 3-14, 3-15, 3-22, 3-23 echoes (sounder)......................................4-19 Echo averaging............................................. 3-28 radar display .............................................5-27 Echo offset (sounder) ................................... 5-30 Compass display .....................
INDEX H Memory Heading line.................................................. 3-17 clearing..................................................... 7-12 Head-up mode.............................................. 3-10 testing......................................................... 7-6 Highway display.............................................. 2-5 Memory cards HL OFF soft key............................................ 3-17 error messages ..........................................
INDEX P switching waypoints in route navigation ... 2-51 Picture advance speed .................................4-17 voyage based ........................................... 2-39 PLOTTER SETUP menu ................................5-4 PLOTTR CNTRL soft key .............................1-13 Port, port services icons .........................................................2-13 navigating to .............................................2-47 Position offset (GPS Receiver) .....................
INDEX color.......................................................... 2-20 W displaying other targets'............................ 2-19 WAAS ......................................................xii, 5-21 displaying own ship's................................ 2-18 Watchman .................................................... 3-32 erasing all own ship's ............................... 2-24 Water temperature alarm ............................. 4-23 erasing all targets' ................................
