Back INSTALLATION MANUAL COLOR DGPS/PLOTTER GP-1850WD COLOR GPS PLOTTER GP-1850W SAFETY INSTRUCTIONS SYSTEM CONFIGURATION.................................................................................. i EQUIPMENT LISTS .............................................................................................. ii 1. INSTALLATION ................................................................................................. 1 1.1 Installation of Display Unit ..........................................
SAFETY INSTRUCTIONS Safety Instructions for the Installer WARNING Do not work inside the equipment unless totally familiar with electrical circuits. Hazardous voltage which can shock, burn or cause serious injury exists inside the equipment. Turn off the power at the mains switchboard before beginning the installation. Post a sign near the switch to indicate it should not be turned on while the equipment is being installed.
This page is intentionally left blank.
SYSTEM CONFIGURATION The GP-1850W/1850WD mainly consists of a display unit and a GPS antenna. A DGPS beacon receiver is provided inside the display unit for GP-1850WD type. The mini chart card drive in the display unit loads electronic charts. External equipment which may be connected include an autopilot and a DGPS beacon receiver (GP-1850W). Antenna unit GPA-019 (GP-1850WD) Antenna unit GPA-017 (GP-1850W) Antenna unit Receives signal from GPS satellite and beacon reference station (GP-1850WD only).
EQUIPMENT LISTS Standard supply Name Type Code No. GP-1850W-E - GP-1850WD-E - GPA-017 - Qty Display Unit Remarks 1 for GP-1850W Antenna Unit 1 - GPA-019 for GP-1850WD Spare Parts* SP14-02501 004-375-260 1 Fuse Installation Materials* CP14-05200 000-041-496 1 Power cable, cable assy. Accessories* FP14-02410 000-041-535 1 FP14-02401, FP14-02403 *: Refer to Packing list at the end of this manual. Optional equipment Name DGPS Beacon receiver kit Antenna cable assy.
EQUIPMENT LISTS Optional equipment (con’t) Name Type Code No.
EQUIPMENT LISTS This page is intentionally left blank.
1. INSTALLATION 1.1 Installation of Display Unit Mounting considerations The display unit can be installed on a tabletop, on the overhead or flush mounted in a console or panel. Hard Cover Tabletop Overhead Tabletop, overhead mounting methods When selecting a mounting location for the display unit keep the following in mind: • Keep the display unit out of direct sunlight. • The temperature and humidity should be moderate and stable. • Locate the unit away from exhaust pipes and vents.
1. INSTALLATION • Rubber foot which absorb vibration (supplied) maybe attached as below if vibration is a problem. Rubber foot TM-166 No.18 black 45 5mm Aline with edge of hanger. Mounting procedure Follow the procedure below to mount the display unit on a tabletop or the overhead. Tabletop, overhead mounting 1. Fix the hanger by four tapping screws 5 X 16. 2. Screw knob bolts in display unit, set it to hanger, and tighten knob bolts. 3. Attach hard cover to protect LCD.
1. INSTALLATION Flush mounting Note: Use supplied pan head screws when the thickness of the bulkhead is from 11 to 14 mm. For bulkhead which exceeds 14 mm in thickness the length of the pan head screws should be bulkhead thickness plus 7.3±1.5 mm. Also the length of B should max. 7mm. B A 1. Prepare a cutout in the mounting location whose dimensions are as shown on the next page. 2. Fix the display unit by six pan head screws M4 X 20. Refer to the outline drawing on page D-2. 242 0.5 6-R2.
1. INSTALLATION 1.2 Installation of Antenna Unit Mounting considerations Install the antenna unit referring to the installation diagram on page D-3 or D-4. When selecting a mounting location for the antenna unit, keep in mind the following points: • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS satellite signal. • The location should be well away from a VHF antenna. A GPS receiver is interfered by a harmonic wave of a VHF antenna.
2. WIRING All wiring are terminated at the rear of the display unit. Display unit Antenna unit GPA-017 GPA-019 (GP-1850WD) (GP-1850W) Earth terminal Ground ANT XDR TEMP/SPD DGPS NMEA + GND 1 3 2 12 - 24 VDC External equipment DGPS beacon receiver (option for GP-1850W, Black RS-232C only) White Shield Display unit, rear view Power cable Connect the power cable to the power connector. Connect the leads to the battery (12 or 24 VDC); white to plus(+) terminal and black to minus(-) terminal.
2. WIRING Antenna unit Connect the antenna cable to the ANT connector. Ground The display unit contains several CPUs. While they are operating, they radiate noise, which can interfere with radio equipment. Ground the unit to prevent interference. The grounding wire should be 1.25 sq or larger and as short as possible. Connect the grounding wire to ship's ground.
2. WIRING Extension cable line-up (in case of 15 m, 30 m or 50 m) Fabricate the end of the antenna cable and attach the coaxial connector. Details are shown on the page 8. Antenna unit GPA-019S/017S : Connector Conversion cable assy. Antenna cable 1m 30 m or 50 m 1m To display unit Fabricate locally. (See the page 8.
2. WIRING How to attach the N-P-8DFB connector Outer sheath Armor Dimensions in millimeters. Inner sheath shield 50 Remove outer sheath and armor by the dimensions shown left. Expose inner sheath and shield by the dimensions shown left. 30 Cover with heat-shrink tubing and heat. Cut off insulator and core by 10mm. 10 30 Twist shield end. Ship on clamp nut, gasket and clamp as shown left. Clamp nut Gasket Clamp (reddish brown) Aluminum foil Fold back shield over clamp and trim. Trim shield here.
3. INITIAL SETTINGS 3.1 NMEA Setting NMEA port This setting should be done when connecting with other equipment, autopilot, radar or remote display. 1. 2. 3. 4. 5. Press the [MENU] key. Press the CONFIGURATION soft key. Press the SETUP NMEA PORT1 soft key. Press the cursor pad to select FORMAT. Press the EDIT soft key to display the following window. ▲ OUTPUT FORMAT SETUP PORT1 ▲ NMEA0183 Ver1.5 NMEA0183 Ver2.0 ▼ ENTER CANCEL DGPS 3D Output format window (PORT 1) 6.
3. INITIAL SETTINGS DGPS port Set the following when connecting with DGPS beacon receiver GR-80 or the DGPS beacon receiver is incorporated, PC to the DGPS port. Note: Signal level for DGPS port is RS232C. 1. 2. 3. 4. Press the [MENU] key. Press the CONFIGURATION soft key. Press the SETUP NMEA/DGPS PORT 2 soft key. Select FORMAT, and then press the EDIT soft key. The following window appears. ▲ OUTPUT FORMAT NMEA 0183 ▲▲▲ VER 1.5 ▲ NMEA0183 Ver1.5 NMEA0183 Ver2.
3. INITIAL SETTINGS 3.2 Output Data Sentences Select output data sentences for external equipment as follows. 1. 2. 3. 4. Press the [MENU] key. Press the CONFIGURATION soft key. Press the SETUP NMEA PORT1 soft key. Press the SELECT SNTNC. soft key to display the SELECT SENTENCE window. ▲ ▲ SELECT SENTENCE AAM APB ON BOD BWR* GGA GLL ON RMA RMB ON RMC ON VTG ON WPL XTE ZDA ON SELECT SNTNC. ON/OFF RETURN DGPS 3D *: BWR for Rhumb line BWC for Great circle Select sentence window 5. 6. 7. 8. 9.
3. INITIAL SETTINGS Input/Output data sentences Port Format Input NMEA NMEA-0183 Ver. 2.0 Ver. 1.5 Output IEC1162 Input NMEA-0183 Ver. 2.0 DGPS Ver. 1.5 RS232C Output RTCM104 Data Remarks TLL*1, MTW, WPL*1, DBT/DPT WPL: GP only NMEA Ver 1.5: DBT NMEA Ver 2.0: DPT AAM, APB, BOD, BWC/BWR, GGA, GLL, RMA, RMB, RMC, VTG, WPL, XTE, ZDA, MTW, GTD*2 GREAT CIRCLE: BWC RHUMB LINE: BWR TLL*1, MTW, WPL*1, DBT/DPT WPL: GP only NMEA Ver 1.5: DBT NMEA Ver 2.
3. INITIAL SETTINGS 3.4 DGPS Setting When external GPS beacon receiver (output: RS-232C only) is connected or the DGPS beacon receiver is incorporated, set the DGPS mode referring to the following procedure. 1. Press the [MENU] key. 2. Press the GPS/DGPS/TD OPTIONS soft key. 3. Press the DGPS/WAAS SETUP OPTIONS soft key. FORMAT DGPS/WAAS MODE BEACON FREQUENCY BEACON BAUD RATE WAAS SEARCH CORRECTIONS DATA SET DGPS/WAAS ALARM DGPS WAAS NMEA OFF 0183 VER 1.
3. INITIAL SETTINGS 6. Select BEACON FREQUENCY by the cursor pad. 7. Press the EDIT soft key to display the following message. BEACON FREQUENCY AUTO MANUAL ▼ ▲ 284.0 kHz ▼ Beacon frequency window 8. Select AUTO or MANUAL by the cursor pad. When you select MANUAL, operate the cursor pad to move the cursor to frequency dialog box. And press the cursor pad to select the frequency desired. AUTO: DGPS reference station can be searched automatically. 9. Press the [ENTER] key. 10.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) The DGPS beacon receiver GR-7000A can be incorporated in the GP-1850W to provide it with DGPS capability. Two kinds of kit are available as shown. GR-7000A-1650-15N-019S GR-7000A-1650-10N-019 Name Type Code No. Qty Antenna Unit GPA-019 000-142-416 1 Beacon Receiver GR-7000A 000-143-249 1 Connector Assy.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) Disassembly Procedure 1. Turn off the power. Wait at least one minute before opening the cover, to allow capacitors to discharge. 2. Remove nuts attached to DGPS, NMEA and power supply connectors at the rear of the display unit. Removing cover assembly 3. Remove nut and washer attached to ANT connector. 4. Remove ten screws at rear of the display unit to detach panel/chassis assembly from the cover assembly.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) Installation of beacon receiver Procedure 1. Dismount chassis assembly from panel/chassis assembly by disconnecting the connector and PH8P from J8 on MAIN Board shown in the figure below. Remove two ties (CV-100). Chassis assembly PH8P Connector Panel assembly Dismounting chassis assembly 2.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) Handling of Coaxial Cable • Do not touch the connector with bare hands; use gloves. • Use radio pincers to remove, and pull out straightly. • Plug in connector straightly. 3. Fasten the GR-7000A (DGPS beacon receiver) to the heat sink with four 3X8 screws as shown in the figure below. Screws (3 X 8), 4pcs. DGPS beacon receiver GR-7000A GN-8091 Installation of DGPS beacon receiver 4.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) 5. Close the cover of GR-7000A passing the two cables out through respective notches in the cover. 6. Plug PH6P-W-L240 connector to J2 on the GR-7000A through the cover. 7. Wire cable assembly as shown in the figure below. Reattach this tape as shown right after the DGPS connection. To J8 of ANLG Board GN-8091 J2 Connector PH6P-W-L240 GR-7000A J1 J3 J2 Wiring the Cable assembly 8. Mount the ANLG board on the heat sink referring to step 2.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) 9. Connect J1 of GR-7000A to J8 of ANLG board (Refer to previous page). 10. Mount chassis assembly on the panel assembly. Connect 8P connector and 6P connector to Main board as shown in the figure below. Attaching chassis assembly 11. Reassemble the display unit.
4. INCORPORATION OF DGPS BEACON RECEIVER KIT (for GP-1850W) Note: When reattaching the cover, confirm the following parts are attached. • Inside of the cover: Shield gasket, GN gasket (See the figure below.) • On ANLG Board: Connector gasket (See the page 16.) GN gasket Shield gaskets Checking the beacon receiver 1. 2. 3. 4. 5. Press the [MENU] key. Press the CONFIGURATION soft key. Press the SYSTEM MENU soft key. Press the SELF TEST soft key.
This page is intentionally left blank.
ACCESSORIES ACCESSORIES SPARE PARTS UNIT （E017) FP14-02403 FP14-02401 000-808-732 000-805-494 TM-166 No.18 ｸﾛ 000-804-742 5X16 SUS304 1種 M4X20 SUS304 004-375-270 FP14-02401 000-549-064 FGBO-A 5A AC125V 000-041-403 000-041-808 GPA-017 SP14-02501 DESCRIPTION/CODE № GP-1850W-E OTHER INSTALLATION MATERIALS OUTLINE GP-1850W 2 4 6 1 3 1 1 Q'TY （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.
ACCESSORIES ACCESSORIES SPARE PARTS UNIT FP14-02403 FP14-02401 000-808-732 000-805-494 TM-166 No.18 ｸﾛ 000-804-742 5X16 SUS304 1種 M4X20 SUS304 004-375-270 FP14-02401 000-549-064 FGBO-A 5A AC125V 000-142-416 000-041-812 GPA-019 SP14-02501 DESCRIPTION/CODE № GP-1850WD-E OTHER INSTALLATION MATERIALS OUTLINE GP-1850WD（E019) 2 4 6 1 3 1 1 Q'TY （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.
A-3 14CP-X-9857 -0 ＰＡＣＫＩＮＧ ＬＩＳＴ 1/1 GP-1850WD（E) N A M E ユニット O U T L I N E DESCRIPTION/CODE № Q'TY UNIT GP-1850WD-E 指示器 1 DISPLAY UNIT 000-041-812 予備品 SPARE PARTS SP14-02501 FGBO-A 5A AC125V ﾋｭｰｽﾞ 3 FUSE 000-549-064 付属品 ACCESSORIES FP14-02401 FP14-02401 ﾊｰﾄﾞｶﾊﾞｰ組品 1 HARD COVER ASSY. 004-375-270 付属品 ACCESSORIES FP14-02403 M4X20 SUS304 +ﾅﾍﾞｾﾑｽﾈｼﾞB 6 WASHER HEAD SCREW 000-804-742 5X16 SUS304 1種 +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 4 +TAPPING SCREW 000-805-494 TM-166 No.
A-4 20AG-X-9404 -1 CODE NO. 1/1 TYPE 工事材料表 GP-80,GP-90,SC-55,GP-3500/F GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 INSTALLATION MATERIALS 番 号 NO. 名 称 NAME 略 図 OUTLINE ｱﾝﾃﾅｹｰﾌﾞﾙ組品 1 型名／規格 DESCRIPTIONS 用途／備考 REMARKS 8D-FB-CV *30M* ｹｰﾌﾞﾙ組品 選択 TO BE SELECTED 選択 TO BE SELECTED 1 ANTENNA CABLE ASSY. CODE NO. 2 数量 Q'TY 000-111-547 8D-FB-CV *50M* 1 CABLE ASSY. CODE NO. 000-117-599 ＦＵＲＵＮＯ （略図の寸法は、参考値です。 ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ. DIMENSIONS IN DRAWING FOR REFERENCE ONLY.
A-5 CODE NO. 004-372-420 TYPE CP20-01701 20AG-X-9405 -1 1/1 工事材料表 INSTALLATION MATERIALS 番 号 NO. 名 称 NAME 略 図 OUTLINE 変換ｹｰﾌﾞﾙ組品 1 型名／規格 DESCRIPTIONS 2 CONVERT CABLE ASSY. ﾋﾞﾆｰﾙﾃｰﾌﾟ 1 VINYL TAPE ｺﾈｸﾀ(N) 000-835-215 N-P-8DFB 1 CONNECTOR CODE NO. 絶縁ﾃｰﾌﾟ 4 000-123-809 NO360 02X19X10000 ｸﾛ ｴｽﾛﾝ CODE NO. 3 用途／備考 REMARKS NJ-TP-3DXV-1 CODE NO. 2 数量 Q'TY Uﾃｰﾌﾟ 000-111-549 0.5X19X5M 1 SELF-BONDING TAPE CODE NO. 000-800-985 ＦＵＲＵＮＯ （略図の寸法は、参考値です。 ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
D-2
D-3 Feb.
D-4 Feb.
Jan.5'04 H.
C B A 0.2m,φ5.3 DPYC-1.5 *1 ５６ １２ （−） 整流器 （＋） RECTIFIER PR-62 *2 *1 IV-8SQ 1 2 3 NOTE *1. LOCAL SUPPLY. *2. OPTION. *3. FITTED AT FACTORY. *4. OPTIONAL LEVEL CONVERTER REQUIRED FOR CURRENT LOOP OR RS422 OUTPUT. NMEA J6 TD-A TD-B RD-H RD-C NC SHIELD 1 2 3 4 5 6 7 1 2 3 4 5 6 DWG.No. SCALE APPROVED P アカ RED アオ BLU C4425-C01- C MASS Y. Hatai kg E. MIYOSHI TAKAHASHI. T P NMEA0183 Ver 2.0/1.
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : AUG . 2002 A2 : AUG . 27, 2004 Pub. No.
