IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement.
SAFETY INSTRUCTIONS Read these safety instructions before you operate the equipment. WARNING CAUTION Indicates a condition that can cause death or serious injury if not avoided. Indicates a condition that can cause minor or moderate injury if not avoided. Warning, Caution Prohibitive Action WARNING The radar antenna sends the electromagnetic radio frequency (RF) energy. This energy can be dangerous to you, especially your eyes.
SAFETY INSTRUCTIONS WARNING WARNING Keep units other than the radar antenna away from the rain and water. Do not depend on one navigation device for the navigation of the vessel. Fire or electrical shock can occur if water gets inside the equipment. Always check your position against all available aids to navigation, for the safety of vessel and crew. Do not disassemble or modify the equipment. Fire or electrical shock can occur if the equipment is disassembled or modified.
TABLE OF CONTENTS FOREWORD ...................................................................................................................xi SYSTEM CONFIGURATION ........................................................................................xiii 1. OPERATIONAL OVERVIEW .................................................................................1-1 1.1 The NavNet 3D System ............................................................................................. 1-1 1.1.
TABLE OF CONTENTS 2.10.5 SST Alarm ....................................................................................................2-14 2.10.6 Speed ...........................................................................................................2-14 2.10.7 Trip Log Alarm ..............................................................................................2-14 2.10.8 Countdown Timer .........................................................................................2-14 2.10.
TABLE OF CONTENTS 4.10 How to Show or Hide All Points ............................................................................... 4-11 4.11 How to Go to a Point ................................................................................................ 4-12 4.11.1 How to go to an On-screen Point ................................................................. 4-12 4.11.2 How to go to Cursor Position ....................................................................... 4-13 4.11.
TABLE OF CONTENTS 6.8 How to Measure the Bearing to a Target..................................................................6-11 6.8.1 How to Measure Bearing with an EBL..........................................................6-11 6.8.2 How to Erase an EBL ...................................................................................6-12 6.8.3 How to Select True or Relative Bearing .......................................................6-12 6.9 How to Off-center the Picture ........................
TABLE OF CONTENTS 7.4 Manual Fish Finder Operation.................................................................................. 7-10 7.4.1 How to Select the Manual Mode .................................................................. 7-10 7.4.2 How to Select a Display Range.................................................................... 7-10 7.4.3 How to Shift the Range ................................................................................ 7-10 7.4.4 How to Adjust the Gain ............
TABLE OF CONTENTS 11. SIRIUS WEATHER RECEIVER ...........................................................................11-1 11.1 Weather Display Introduction ...................................................................................11-1 11.2 Weather Icons ..........................................................................................................11-2 11.3 Weather Menu ..........................................................................................................11-3 11.
TABLE OF CONTENTS 14.5 The Magnetron......................................................................................................... 14-3 14.6 Troubleshooting ....................................................................................................... 14-4 14.6.1 General Troubleshooting.............................................................................. 14-4 14.6.2 Radar Troubleshooting................................................................................. 14-4 14.6.
FOREWORD A Word to the Owner of the MFDBB Congratulations on your choice of the MFDBB Multi Function Display, an integral part of our new NavNet 3D series of multi-function displays. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment.
FOREWORD • Compliant with IEC 62252 Ed.1:2004 (Clauses 4.33, 5.33, Annex D) Fish finder (option) • Measures the depth to the bottom and displays underwater conditions in multi-colors according to echo strength. A monochrome presentation shows the echoes in shades of gray. (*Number of colors depends on network sounder, color sounder.) • The zoom mode enlarges the targets. • Automatic and manual operation. Auto mode automatically adjusts range, gain and clutter according to purpose, fishing or cruising.
SYSTEM CONFIGURATION RADAR SENSOR DRS2D/DRS4D RADAR SENSOR DRS4A/DRS6A/DRS12A/DRS25A OR DRS4A DRS6A DRS12A DRS25A POWER SUPPLY UNIT PSU-013*1 12-24 VDC*2 MONITOR MU-155C/170C, etc. AIS RECEIVER, HEADING SENSOR or EXTERNAL BUZZER VIDEO IN (CCD CAMERA, MAX. 4) GPS NAVIGATOR GP-330B PROCESSOR UNIT MPU-001 LINE OUT (SPKR, ETC.) USB DEVICE (MOUSE, KYBD) LINE IN (MIC, for future use) NMEA 2000 (GP-330B, ETC.
SYSTEM CONFIGURATION This page is intentionally left blank.
1. OPERATIONAL OVERVIEW This chapter provides the information necessary to get you started using your system. Some of the topics are how to turn on the equipment and an introduction to the main displays. Standards used in this manual • The keys and controls on the control panel are shown in bold face, for example the DISP key. Other items that have a label, for example, the soft controls related to the RotoKey, are shown in brackets in normal typeface. For example, [Head Up].
1. OPERATIONAL OVERVIEW Then, hold down the power switch of the MFD that was responsible for loss of power synchronization for three seconds. 1.1.1 How to sleep the equipment You can sleep the equipment when its use is not required continuously. With the Standard or Full RotoKey set active, push the RotoKey, rotate the key to select [Sleep] then push the key. To un-sleep the equipment, push the power key until the picture appears. 1.
1. OPERATIONAL OVERVIEW 9 10 8 12 11 7 13 14 6 15 5 4 16 3 1 2 17 DCU12 Control description No. Label Function 1 (MCU-001) BRILL (DCU12) Mouse operation Short-push: Turn ON the power on. Adjust the panel dimmer. On the DCU12 it also adjusts display brilliance. Long push: Turn the power off. - 2 Card drive Card drive for memory cards. - 3 SAVE/MOB SAVE: Save the current position as a point. MOB: Save the current position as an MOB position.
1. OPERATIONAL OVERVIEW No. 1-4 Label Function Mouse operation 8 POINTS/ROUTE POINTS: Save the cursor position as a point. ROUTE: Activate the route building tool. - 9 GO TO/LIST GOTO: Set the cursor position as the destination. LIST: Open the Points menu. - 10 CursorPad • Pad: Move the cursor. • Like the "left-click" button on a PC mouse. This button has the name “left-click“button in this manual. • Move the cursor. • Left mouse button 11 (right-click button) Show a pop-up menu.
1. OPERATIONAL OVERVIEW 1.3 Power ON and OFF Press to turn the power ON. To turn the power OFF, press and hold the same key. The message "All Network Devices will shut down in Xm XXs" displays the amount of time remaining until power off. When you turn on the power, two or three beeps sound and the lamp near the power switch lights. The start-up screen appears with the progress bar (at the bottom of the screen). The progress bar moves to the right as the procedure continues.
1. OPERATIONAL OVERVIEW 1.5 How to Select a Display Use the DISP key and the RotoKey to select a display, from the display selection window. The displays available depend on your system configuration and the HotPage settings on the [My NavNet] menu. (You can change the display selection window according to your needs and system configuration.) 1) Press the DISP key to show the display selection window. (The labels in the illustration below do not appear on the actual display.
1. OPERATIONAL OVERVIEW 1.6 SD Cards The SD card stores the tracks, routes, points, settings, etc. Set and remove SD cards as shown below. The recommended capacity for the cards is 128 MB to 2 GB. (The Secure Digital High Capacity (SDHC) SD cards cannot be used.) How to format an SD card You do not normally need to format an SD card for use with the system. If the card becomes damaged, format the card with a formatting program that is compatible with the specifications of the SD card.
1. OPERATIONAL OVERVIEW 1.7 Chart Plotter Introduction The chart plotter provides a small world map in raster format. A vector chart for the US coastline (with Alaska and Hawaii) is provided also. The plotter section has functions to enter way points, and create and plan routes. The chart plotter receives position information supplied from the position-fixing equipment like GPS or DGPS. Your position is marked on the screen with the boat icon.
1. OPERATIONAL OVERVIEW 1.8 Radar Introduction A radar system operates in the microwave part of the radio-frequency (RF) range. The radar detects the position and movement of objects. Objects are shown on the radar display at their measured distances and bearings in intensities according to echo strength. The radar display is available in head-up, course-up and north-up modes and orientation in true and relative motion. The relative motion display shows other vessels movement relative to your vessel.
1. OPERATIONAL OVERVIEW 1.9 Fish Finder Introduction The fish finder screen provides a “picture” of the echoes found by the fish finder. Echoes are scrolled across the screen from the right position to the left position. The number of minutes an echo is displayed on the screen is controlled by the picture advance speed. The echoes at the right position are the current echoes. These echoes can be from separate fish, a school of fish, or the bottom.
1. OPERATIONAL OVERVIEW 1.10 The Cursor The cursor is always displayed on the radar, chart plotter and fish finder displays and has the functions shown below. • Find the position, range and bearing to an object on the chart plotter and radar displays • Find the depth to an object on the fish finder display. • Select a position for a waypoint on the chart plotter display. • Select an item. For example, a waypoint on the chart plotter display.
1. OPERATIONAL OVERVIEW 1.11 Status Bar The status bar is the horizontal bar at the top of any display. This bar shows operation information with messages, and sensor state with the icons. The color of the bar changes according to the types of messages as shown below.
1. OPERATIONAL OVERVIEW 1.12 RotoKey and Soft Controls The main function of the RotoKey is to display the [soft controls], a revolving menu of soft controls which change with operating mode. A short-push or rotation of the key accesses a set of the functions that you select at the [My NavNet] menu, among [Basic], [Standard], [Full] and [Custom]. A long-push displays all of the soft controls for the current mode.
1. OPERATIONAL OVERVIEW 1.13 Pop-up Menus The pop-up menus let you quickly access the commands according to the selected object or active display. To display a pop-up menu, select an object and hit the rightclick button. A pop-up can also be shown if you push the same button in any position on the active display. The illustration below shows the Radar pop-up menu. Status icon Green: ON Gray: OFF No icon Push RotoKey to process item.
1. OPERATIONAL OVERVIEW 1.14 Data Boxes The data boxes show the navigation data. You can select the data to display in the boxes, and show or hide the boxes as necessary. A box can show one or more data. Multiple data are scrolled according to the scrolling time set on the [DataBox] menu. The data that you can show depends on your system configuration. You can show a maximum of five boxes, four at the bottom-left corner and the cursor data box at the top-right corner. The no.
1. OPERATIONAL OVERVIEW 1.15 Menu Introduction The menu system has a maximum of 15 main menus and related sub menus. The number of menus depends on equipment connected. To show the menu, press the MENU key. How to use the menu 1. Press the MENU key to open the menu. The last-used menu appears. The Alarm log automatically appears if an alarm condition is broken. The icons in the rectangle on the left show all the available menus.
1. OPERATIONAL OVERVIEW Menu description Menu icon Function Menu icon Select the shape for the boat icon, and control the track of your vessel. Function Set the ARPA and AIS targets, and manage the DSC message information feature. Targets Ship & Track Set points. Set the weather display. Weather Points Set routes. Routes Set the alarms. Alarms Set the chart plotter display. Set the items common to all modes, for example, key beep and the size of the font.
1. OPERATIONAL OVERVIEW ground color of the selector is blue, which indicates the menu is selected, but not active. 3. Do one of the following according to menu type: • For single sub menu, push the RotoKey to start the menu operation. • More than one sub menu, push the RotoKey. Rotate the RotoKey to select a sub menu then push the key to validate selection. Rotate the key right for selection in the left-to-right direction. Rotate the key left for selection in the opposite direction.
1. OPERATIONAL OVERVIEW Menu item type Status icon Status icon Alphanumeric data input box Depth Alarm Value Slider bar Procedure Items which you can activate or deactivate have a status icon. Push the RotoKey to show the icon in green to activate the item, or gray to deactivate. Rotate the RotoKey to select alphanumeric character (A-Z, 0-9) then push the key to validate selection. Rotate the key right for forward alphanumeric order. Rotate the key left for reverse alphanumeric order.
1. OPERATIONAL OVERVIEW 1.17 Boat Icon The boat icon marks current position, and the default shape is "simplified icon." If your vessel is different, you can change the shape of the boat icon to match your vessel. Appearance of simplified icon (default boat icon) 1. Press the MENU key to open the menu. 2. Open the [My NavNet-General] menu. 3. Use the RotoKey to select [Boat Icon]. 4. Use the RotoKey to select the boat icon which best matches your vessel. 5. Press the MENU key to close the menu.
1. OPERATIONAL OVERVIEW 1.18 Man Overboard (MOB) Use the MOB function if a person or object falls overboard. You need either position data from a navigation device, or heading and speed data to calculate position by dead reckoning. You activate the MOB from the chart plotter display and MOB position is marked on both the chart plotter and radar displays. To mark MOB position, long-push the SAVE/MOB key on the chart plotter display.
1. OPERATIONAL OVERVIEW MOB information There are two types of MOB information, simple and detailed. Simple information includes point name (MOB), and range and bearing to the MOB position. Detailed information includes simple information plus the information shown below.
1. OPERATIONAL OVERVIEW 1.19 Dual-Head Display The dual-head display lets you use primary and secondary displays on the main bridge. The Processor Unit MPU-001 can output two picture data to the displays connected to its DVI1 and DVI2 ports. You can select how to show the pictures on the two displays: the same picture on both displays or picture split across both displays. This is set at the installation. Primary Display Secondary Display DVI1 DVI2 Processor Unit MPU-001 No.1 MCU-001 USB Mouse No.
1. OPERATIONAL OVERVIEW Item Feature Description Operating characteristics Switching application There are two ways to change active display: 1) Operate the CTRL key. The cursor moves to the center of the active screen after the cursor is moved between screens. 2) Move the cursor into the display with the mouse or Cursorpad. Hotpage selection Ten hotpages available for both displays. Hotpage editing Hotpage can be edited on both displays. No. of mouse One No.
1. OPERATIONAL OVERVIEW 1.20 Facsimile Receiver FAX-30 The FURUNO Facsimile Receiver FAX-30 installs in the NavNet network and controlled from a NavNet display. Below are the steps to start fax operation. 1. At installation of this equipment, connect the FAX-30 to the NavNet and check that the equipment identifies the FAX-30, through the Installation Wizard. 2. Select the "full screen" FAX display. For the procedure, refer to the section 13.3 "How to Set the Display Selection Window".
1. OPERATIONAL OVERVIEW 1.21 AIS Transponder FA-30, FA-50 The FURUNO AIS Transponder FA-30 (FA-50) installs in the NavNet network and can be controlled from a NavNet display. To access the main menu of the transponder, do the following: 1. Open the main menu and select the [System] menu. 2. Open the [Other Sensors] sub menu. 3. Use the RotoKey to click the FA-30 (FA-50) button to show the main menu of the transponder. 4.
1. OPERATIONAL OVERVIEW 1.22 DSC Message Information The DSC (Digital Selective Calling) message information feature provides, on the chart plotter and radar displays, the MMSI no. and position* of the ships that have transmitted a DSC message to you. A hexagon-shaped marker marks a ship’s position. The marker is color-coded according to the type of DSC message sent, red for distress and dark-blue for non-distress. * Position at the time of message transmission. Position information is not updated.
1. OPERATIONAL OVERVIEW 1.22.3 Operations Available with the DSC Marker With the DSC marker pop-up you can • Delete the selected DSC marker (and its data from the DSC list). • Set the position of the DSC marker as your destination. (See section 4.11.) • Save the position of the DSC marker as a point. (section 4.2.) 1. Put the cursor on a DSC marker then push the right-click button to show the DSC marker pop-up. 2. Rotate the RotoKey to select desired item then push the RotoKey. 3.
1. OPERATIONAL OVERVIEW How to add an MMSI no. to the DSC list 1. Show the DSC list then push the RotoKey twice to select []. 2. Push the RotoKey to show the DSC list pop-up. 3. The cursor is selecting [Edit]; push the RotoKey to show the MMSI and Nick Name input window. 4. The cursor is selecting [MMSI]; push the RotoKey. 5. Use the RotoKey to enter MMSI no. (See the instructions on page 1-19 for how to enter data.) 6. Use the RotoKey to select [Nick Name] then push the RotoKey. 7.
1. OPERATIONAL OVERVIEW This page is intentionally left blank.
2. CHART PLOTTER This chapter shows you how to do the following: • Use and prepare the chart plotter • Set chart plotter related alarms • Control the track 2.1 Charts 2.1.1 Chart Description A world map in raster chart format is included in your unit. A vector chart for the US coastline (Alaska and Hawaii included) is provided also. To use this chart plotter as a navigational aid, have electronic charts (stored in the hard disk) for the area you navigate. Contact your dealer about charts for your area.
2.
2.
2. CHART PLOTTER 2.2 Chart Scale You can change the chart scale to change the amount of information shown, or zoom in or out at the location you select. The selected chart scale appears at the top lefthand position on the screen. In the full screen display, the value shown is 1/2 the distance from the top of the screen to the bottom of the screen. There are two methods to change the chart scale, the RANGE key, and the cursor with the RotoKey.
2. CHART PLOTTER 2.3 Orientation Mode The chart can be shown in head-up, course-up or north-up orientation. To select an orientation mode, use the RotoKey to select the [Head Up], [North Up] or [Course Up] soft control. Another method is to put the cursor on the orientation mode icon at the top-left position then push the left-click button. Orientation mode icon Description of orientation modes Head-up: Displays the chart with the current compass heading of your vessel at the top of the screen.
2. CHART PLOTTER 2.5 The Boat Icon The boat icon appears at current position. The default shape is “simplified icon”. Other shapes are available, from the menu, like yacht and sailboat. The boat icon has the functions indicated below also. • The Heading line is a straight line that runs from your position and this line shows the current heading. • The COG/SOG predictor is a vector line that runs from the boat icon. This predictor shows estimated course and speed of your vessel.
2. CHART PLOTTER Boat icon pop-up menu The Boat Icon pop-up menu controls the COG/SOG predictor, heading line and track. To display this pop-up, put the cursor on the boat icon then push the right-click button. Boat icon pop-up menu Turn on or off as appropriate. To set COG/SOG predictor time, select Set COG/SOG Predictor Time and hit left-click button to show the Ship & Track menu. COG/SOG Predictor Time Select COG/SOG Predictor Time and push RotoKey. Rotate RotoKey to select a time.
2. CHART PLOTTER 2.6 How to Find the Range and Bearing to a Location The "ruler" feature measures the range and bearing between any two points on your chart. Range and bearing between the two points are digitally indicated on the screen. 1. Use the Cursorpad to put the cursor on the starting point. 2. Long-push the RotoKey. 3. Use the RotoKey to select [Ruler]. 4. Use the CursorPad to move the cursor to the 2nd point. A dashed line runs between the start point and the 2nd point.
2. CHART PLOTTER 2.8 Multiple Chart Plotter Displays A maximum of three chart plotter displays can be shown on one screen. The multiple chart plotter display lets you see the conditions around your vessel on both short and long ranges. Also, you can see how your vessel moves toward your destination from more than one angle. For example, you can show one display in 2D and another in 3D. The following features can be adjusted individually.
2. CHART PLOTTER 2.9 Cartographic Text and Objects on Vector Charts This section shows you how to show or hide the various cartographic objects and text information that appear on vector charts. 2.9.1 Control Visibility of Text and Object Information The [Chart-Vector] menu controls the visibility of text and object information, for example, buoy names and light description. Chart-vector menu items Chart Symbols: Select the chart symbol type.
2. CHART PLOTTER Name: Show or hide geographic names. Shallow Contour: Show shallow depth contours in dark blue. Safety Contour: Show safety depth contours in medium blue. Deep Contour: Show deep depth contours in light blue. Depths greater than 1800 feet are shown in white. Traffic Routes: Show or hide traffic routes. Display Routes Bearings: Show or hide route bearings. Soundings: Show or hide depth soundings.
2. CHART PLOTTER Chart-config menu description S-52 Vector Chart Display Mode: Set the level of information to show on the chart. The selections are [Basic], [Standard], [Other], [Fishing], [Custom], and [Default]. The chart features are turned on or off according to setting. Unknown Object: Unknown objects that appear on the chart. Chart Data Coverage: Geographic names and geographic objects. Bottom Features: Improved seabed presentation. Traffic Routes: Marine traffic routes.
2. CHART PLOTTER 2.10 Alarms This section describes the alarms available with the chart plotter: • XTE alarm • Anchor watch alarm • Proximity alarm • Depth alarm • Sea surface temperature alarm • Sea surface temperature shear • Speed alarm • Trip log alarm • Countdown timer • Alarm clock 2.10.1 XTE Alarm The XTE alarm tells you when your vessel is not on course by more than the set value. When the XTE alarm is active, two dashed lines mark the XTE alarm boundaries, red for starboard, green for port.
2. CHART PLOTTER 2.10.3 Proximity Alarm The proximity alarm tells you when your vessel is near a point for which an avoidance circle, set on the [Points] list, is active. When your vessel is within the set value, audio and visual alarms are released. 2.10.4 Depth Alarm The depth alarm tells you when the depth to the bottom is over or under the value you set. Requires depth data. 2.10.
2. CHART PLOTTER 2.10.10 How to Set an Alarm 1. Press the MENU key to open the menu. 2. Open the [Alarms-General] menu. 3. Use the RotoKey to select an alarm item then do one of the following: a) For the alarms which have a status icon, push the RotoKey to activate or deactivate the alarm. Show the icon in green to activate the alarm, or gray to deactivate the alarm. b) For the depth, speed and SST alarms, select the combo box of the item then push the RotoKey to show the alarm options.
2. CHART PLOTTER 4. Use the RotoKey to select the [Alarm Value] box for the alarm. 5. Use the RotoKey to set a value. Rotate the key to select a value then push the key to validate the setting. 6. Press the MENU key to close the menu. 2.10.11 Internal/External Alarm The audio alarm is output from this equipment in the default setting. The alarm can be output from this equipment, from external equipment or from both this equipment and external equipment. 1. Press the MENU key to open the menu. 2.
2. CHART PLOTTER 2.10.13 Alarm Log The [Alarm-Log] menu shows the names, date and time that current and past alarms were broken.
2. CHART PLOTTER 2.11 Track The track (or movement) of your vessel is plotted on the screen with position data. Your track lets you see how your vessel has moved. The track is saved to the hard disk if the track is active. A line runs between each track point. The hard disk stores a maximum 10,000 points. When the memory for track points becomes full, the oldest track points are deleted to get space for new track points. Your track remains on the screen when the power is removed.
2. CHART PLOTTER 2.11.3 Track Thickness You can set the thickness of the track to thin, medium or thick. If you are following the same track many times, you can show the track in the thinnest width to keep the screen clear. 1. Press the MENU key to open the menu. 2. Open the [Ship & Track] menu. 3. Use the RotoKey to select [Track Thickness]. 4. Use the RotoKey to select a thickness. 5. Press the MENU key to close the menu.
2. CHART PLOTTER 2.11.4 Track Color Track can be displayed in a single color or multiple colors. For multiple colors, you can display the track according to the conditions shown below. • Depth range • Depth difference • Sea surface temperature range • Sea surface temperature difference • Speed • Date To select the track color: 1. Press the MENU key to open the menu. 2. Open the [Ship & Track] menu. 3. Use the RotoKey both to select [Define Track] and open the options menu. 4.
2. CHART PLOTTER 6. Use the RotoKey to set values. Refer to the description below and on the next page. 999 ft Depth range Sea surface temperature range Speed Depth variation Fixed color Date Sea surface temperature variation Fixed color: Single-color track in white, blue, purple, cyan, green, yellow and red. Depth range: Change the color of the track with depth. Set the a depth limit for each color. For example, the default setting for white is 33 ft.
2. CHART PLOTTER Sea surface temperature range: Change the color of the track with change in sea surface temperature. Set a limit for each color. For example, if the default setting for white is 41.0°F, the track is white for temperatures up to 41.0°F. Sea surface temperature variation: Paint the track in a different color when the sea surface temperature changes by the figure set here. If the setting is +00.
2. CHART PLOTTER 4. Use the RotoKey to enter name. Rotate the key to select a character then push the key to validate your selection. You can use a maximum of eight characters for the name. (To save the track under the name shown in the [Rename] box, push the RotoKey continuously until the box closes. Use the RotoKey to push the OK button.) 5. Press the MENU key to close the menu. 2.11.7 How Replay a Saved Track You can replay saved track on the display to use the track to create a route.
2. CHART PLOTTER 2.11.9 How to Find Information About a Track Simple track information provides the depth and temperature for the location selected on a track. (Depth and temperature sensors are required.) Put the cursor on any part of a track to get this information. Detailed track information includes simple track information plus the information shown below. Press the left-click button to show detailed track information.
2. CHART PLOTTER • Arrows on the track point in the direction to follow the route. Activate Trackback Course to follow (red dashed line) Track First destination Route point Arrows point in direction to follow route Trackback route following options When you are following a trackback route, you can do the following from the Route pop-up menu. • Cancel the route. • Restart following the route. • Reverse the following direction. • Put a point on the route.
2. CHART PLOTTER This page is intentionally left blank.
3. 3D DISPLAY, OVERLAYS 3.1 3D Display The 3D display has native 3D chart design that allows full time 3D presentation. This true 3D environment gives you all of the information you require with no restrictions on the information you can see. You can plan your routes, enter points, etc. like on the 2D chart. The 3D display provides a 3D view of land and sea around your vessel. Land is shown in different shades of light-brown according to height above the sea level.
3. 3D DISPLAY, OVERLAYS How to activate and deactivate the aerial view by the SHIP/3D button Before you do this procedure, open the [Chart-General] menu and activate [3D Pan/ Tilt Mode]. This sequence allows you to adjust the pitch and orientation. 1. Long-push the SHIP/3D button to start the 3D display. 2. Rotate the RotoKey to adjust the pitch, i.e., the vertical angle of view. The range of adjustment is 1-90°. 3. Push the RotoKey to validate the setting. 4.
3. 3D DISPLAY, OVERLAYS 3.1.2 Underwater Display The underwater display provides a look into the water from above the water. This display is available between 7 yards and 1.003 nm. To activate the underwater display, use the RotoKey to select the [3D] and [Underwater] soft controls. You can rotate the picture with W and X on the ScrollingPad. Land Your ship Depth to bottom Underwater Depth contour Underwater display 3.1.
3. 3D DISPLAY, OVERLAYS 3.1.4 How to Make the 3D View Clearer In the 3D display, some topographical features are easier to see if you use the “3D Exaggeration” feature. This feature expands both objects on the chart and the underwater vertically so that you can easily see the shape of the objects and position. To adjust the exaggeration feature, open the [Chart-General] menu and set the level with [3D Exaggeration]. See the available options in the figure shown below.
3. 3D DISPLAY, OVERLAYS 3.2 Overlays Four chart overlays are available on the chart plotter display. These overlays are depth shading, weather, satellite photo, and animation. 3.2.1 Depth Shading Overlay The depth shading overlay shows the depths in red (shallow), yellow (medium) and green (deep). This overlay is available in both 2D and 3D presentations. Use this overlay to find depths. Transparency levels can be adjusted so that the chart data is visible under the color shading.
3. 3D DISPLAY, OVERLAYS 3.2.2 Weather Overlays The weather overlays put weather information on the 2D and 3D displays. These displays are available only in North America and with connection of a Sirius weather receiver. Four types are available: Wx Radar, Wx Data, and Adv Wx Data, and Marine Zone. Use the RotoKey to select [Weather] and a weather soft control then push the RotoKey to hide or show the selected weather display. For detailed information about weather overlays, see chapter 11.
3. 3D DISPLAY, OVERLAYS Weather data overlay The weather data overlay provides forecast data that includes weather radar, sea surface temperature, storm tracks, pop-up weather alerts, etc.
3.
3. 3D DISPLAY, OVERLAYS Marine zone overlay The coastal waters are divided into zones for forecasts.
3. 3D DISPLAY, OVERLAYS 3.2.3 Satellite Photo Overlay You can put the satellite photo for your area on the 2D and 3D displays. Use the RotoKey to select [Overlay] and [Sat Photo] then push the RotoKey to show or hide the satellite photo High-resolution satellite images for the USA coastline are not provided standard, but are available at no cost (except shipping and handling). Users can install multiple satellite photos on the hard drive of the NavNet 3D.
3. 3D DISPLAY, OVERLAYS 3.2.5 Radar Overlay The radar overlay display puts the radar picture on the top of the navigation chart. To display the radar overlay, use the RotoKey to select [Overlay] followed by [Radar]. Push the RotoKey to show or hide the radar overlay. How to set the level of radar echo transparency Open the [Radar] menu and use the RotoKey to select [Echo Transparency for Overlay]. Rotate the RotoKey to set the level of transparency then push the RotoKey.
3. 3D DISPLAY, OVERLAYS 3.2.6 Tidal Information Overlay The NavNet 3D has worldwide tidal and tidal current information. You can overlay this information on the chart plotter display. The tidal information symbol ( ) appears at the locations of tidal recording stations. When you select a symbol, you can get a graph of predicted maximum and minimum tide heights, and times for sunrise and sunset. How to display the tidal information overlay 1. Push the RotoKey to show the soft controls. 2.
3. 3D DISPLAY, OVERLAYS How to show simple tidal information You can display simple information (name, local time and tide height) about a tide by when you put the cursor on a tide icon.
3. 3D DISPLAY, OVERLAYS How to display the tide graph The NavNet 3D has worldwide tide and current information. You can show the tide graph by three methods. • Use the CursorPad to a tidal symbol then push the left-click button to show the tide graph. • Use the CursorPad to select a tidal symbol, push the right-click button then select [Tide Graph] from the pop-up menu.
3. 3D DISPLAY, OVERLAYS 3.2.7 Tidal Current Overlay The tidal current overlay is made from the tidal current data received from NOAA satellites, available in North America. 1. Push the RotoKey to show the soft controls. 2. Use the RotoKey to select [Overlay] followed by [Currents]. 3. Push the RotoKey to show or hide the tidal current display. Arrows of more than one color and size appear on the screen and are pointing in different directions. The arrow indicates the movement of the tidal current.
3. 3D DISPLAY, OVERLAYS This page is intentionally left blank.
4. POINTS 4.1 About Points In navigation terminology, a point is any location you mark on the chart plotter display. A point can be a fishing spot, reference point and other important locations. You can use a point you have entered to set a destination. This unit has 2,000 points into which you can enter position information.
4. POINTS 4.2 Hot to Mark a Point You can mark a point • At current position • At cursor position • From the Points list 4.2.1 How to Mark a Point at Current Position Press the SAVE/MOB key to mark a point at current position. The following occurs. • The default point symbol is put at current position. • The point is saved to the Points list under the youngest empty point number 4.2.2 How to Mark a Point at Cursor Position Use the CursorPad to put the cursor on a location. Press the POINTS/ROUTE key.
4. POINTS 4.2.3 How to Mark a Point from the Points List A point marked from the Points list is put at the current position. To put the point at a different location, edit the point data (position, symbol, etc.) before marking a point. 1. Long-push the GO TO/LIST key to show the [Points] menu. 2. Use the RotoKey to select any tab at the top of the menu. (You can select any tab when you mark a point.
4. POINTS 3. The cursor is selecting [Total]. Push the RotoKey twice then the right side of the display shows the point information like in the illustration shown below. Total no. of points Point settings Point name, range and bearing to point and point group name appear here. 4. If necessary, change the point settings. See section 4.7 "How to Edit a Point from the Points List". 5. Use the RotoKey to click the OK button. 6. Press the MENU key to close the menu. 4.
4. POINTS 4.4 Default Point Settings When you save a point, the equipment saves the point according to the shape, color and group name set on the [Points-General] menu. If those settings do not meet your requirements, you can the settings as shown below. 1. Long-push the GO TO/LIST key to show the [Points] menu. 2. Select the [General] sub menu, shown below. 3. Use the RotoKey to select [Point Symbol], [Point Color] or [Group Name].
4. POINTS 4.5 How to Move a Point You can move a point by two methods: • Move the symbol to a new location. • Enter new position manually on the [Points] list. 4.5.1 How to Move an On-screen Point 1. Set the cursor on the point to move. The point becomes larger if the point is selected correctly. 2. Hit the right-click button to show the Point pop-up menu. Move Go To Edit Rename Delete 3. [Move] is selected. Push the RotoKey. 4. Use the CursorPad to move the symbol to the new location.
4. POINTS 4.6 How to Delete a Point You can delete points by two methods, on the screen and from a Points list. 4.6.1 How to Delete a Point on the Screen Method 1: CANCEL key Put the cursor on the point to delete and press the CANCEL key. Method 2: Pop-up menu 1. Put the cursor on the point to delete. 2. Push the right-click button to show the Points pop-up menu. 3. Rotate the RotoKey to select [Delete]. 4. Push the RotoKey to delete the point from both the screen and the Points list.
4. POINTS 4.7 How to Edit a Point from the Points List You can edit the points you have entered from the [Points] menu. You can select the point to edit on-screen, or from a Points list. 1. On the screen, use the CursorPad to select the point to edit, push the right-click button and select [Edit] from the pop-up menu. (You can also select the point if you long-push the GO TO/LIST key.) Settings for the point selected appear on the right-half of the screen. PT 00 ... 0 m 80.
4. POINTS 5. Select [Point Color] to change the color of the square part of the point symbol. Seven colors are available: red, yellow, green, cyan, purple, blue, and white. 6. Select [Group] to put the point in a point group. [Fishing], [Navigation], [Danger] and [Entertainment] are the default groups. Navigation Danger Entertainment 7. [Depth] and [Water Temperature] are the depth and water temperature at the point location. (You need depth and water temperature data to show this data.
4. POINTS 4.8 How to Find a Point 4.8.1 How to Show a Point at the Center of the Screen You can easily move a point to the center of the screen if you select it on the [Points] menu. 1. In the chart plotter mode, long-push the GO TO/LIST key to open the [Points] menu then open a Points list. 2. Select a point then push the RotoKey. The Points List pop-up menu appears. 3. Use the RotoKey to select [Find on Map]. 4.
4. POINTS • Add new. Add new group. The default group name is GROUP XXX (XXX=next three-digit group number). • Delete. Delete selected group name. Points in the group are not deleted. • Visible. Control visibility of points in a group. 6. Press the MENU key to close the menu. 4.10 How to Show or Hide All Points You can show or hide all points. A point which is currently used in navigation cannot be removed from the screen until the navigation is stopped. 1.
4. POINTS 4.11 How to Go to a Point Select the point to go to from the three methods shown below. • Select the point on the screen • Select the point from the Points list • Select the point with the cursor After you have selected a point, you can do the following. • Restart the cross-track error (XTE) indication. • Stop and restart Go To. Before you try to go to a point, make sure that the path to the point is clear. Make sure to zoom your chart to check for hazards which appear on a smaller scale. 4.11.
4. POINTS 4.11.2 How to go to Cursor Position The benefit of using the cursor position is you do not have to use a saved point. The point is erased when the navigation is cancelled. GO TO/LIST key Put the cursor on the location then push the GO TO/LIST key. Use the RotoKey to select [Go To] or [Go To by Position]. To set the position accurately, use [Go To by Position]. Set the position in the [Validate position] box with the RotoKey.
4. POINTS A red dashed line runs between current position and the point. This line is the course to follow to get to the point. The point arrival area is indicated with a circle, or both circle and line. You can select the arrival area indication method with [Waypoint Switching Mode] in the [Routes-General] menu. To receive an aural alarm when you are within a preset distance, turn on [Waypoint Notification] and set [Switching Circle Radius] on the [Routes-General] menu.
4. POINTS 4.11.3 How to go to a Point Selected from the Points List 1. Long-push the GO TO/LIST key to open the [Points] menu then open the Alpha list. 2. Use the RotoKey to select a point. 3. Push the RotoKey to show the [Points] Menu pop-up. The cursor selects [Go To]. Push the RotoKey. New Point Edit Delete Find on Map The menu is erased and the chart plotter display appears. A red dashed line runs between current position and the point. This line is the course to follow to get to the point.
4. POINTS 4.12 How to Restart and Cancel Navigation to a Point 4.12.1 Restart Navigation When you go to a point, you can restart the navigation to the point from current location. When you steer to keep away from an obstruction or the vessel drifts, you go off course as shown in Line 1 in the figure. If you do not need to return to the original course, you can go to the point from the current position as shown in Line 2 in the figure. Line 2 Obstacle Line 1 Original course 1.
5. ROUTES 5.1 What is a Route? A route is a series of points entered in the order to use for navigation. A route can contain up to a maximum of 100 points, and this equipment stores 200 routes. You create a route by pointing and clicking geographical positions on the screen. These positions are marked with blue solid circles. You can follow a route that you have created if you use the GOTO feature.
5. ROUTES 5.2 How to Create a Route 5.2.1 How to Create a New Route The route points of an inactive route are marked on the display with a blue square and a blue line runs between points. 1. Put the cursor on the 1st point for the route. 2. Push the right-click button to show the Cursor Position pop-up menu. Go To Go To by Position New Point New Route Center on Boat Acquire Target 3. Use the RotoKey to select [New Route]. 4. Use the CursorPad to move the cursor to the next point in the route.
5. ROUTES 5.2.2 How to Insert a Point on a Route You can put a point between route legs when you need an additional point along a route. 1. Put the cursor on a leg of the route. 2. Push the right-click button to show the Routes pop-up menu. 3. Use the RotoKey to select [Insert point]. A dashed line runs between the two points on the selected leg. Drag cursor to location where to insert point 4. Move the cursor where to put a point then press the left-click button. A solid line replaces the dashed line.
5. ROUTES 5.2.4 How to Extend a Route You can extend a route from the last point on the route. 1. Place the cursor on a leg of the route. 2. Push the right-click button to show the pop-up menu. 3. Use the RotoKey to select [Extend Route]. A dashed line runs from the last point to the cursor. 4. Use the cursor to select a location then push the left-click button. 5. Repeat step 4 to enter more points, if necessary. 6. Push the RotoKey to finish. 5.2.
5. ROUTES 5.2.6 How to Join Two Routes You can join two routes to create a new route. The new route takes the name of the 1st route selected and the 2nd route selected is deleted. All route data is updated. How the routes are joined depends on route selection order. The last point of the 1st route selected is joined to the 1st point of the 2nd route selected. The example below shows how two routes are joined according to selection order.
5. ROUTES 5.3 Routes List The saved routes are stored in the Routes list. The list stores the following route data for each route: • Name of route • Length of route • Number of route points • Distance between legs and total distance • Bearing between legs • TTG between legs and total TTG To show the routes list: 1. Press the MENU key to open the menu. 2. Open the [Routes] list. 3. Use the RotoKey to select the route to view.
5. ROUTES 5.4 How to Find Information About a Route on the Screen Put the cursor on a route to get simple route information (name and length of route). Push the left-click button to get detailed information. This information includes name of route, length of route, no. of points, range and bearing to next point, and total time to go. Simple route information 5.
5. ROUTES 5.6 How to Change the Name of a Route The default route name is “RTE” plus the number of the youngest empty route number (RTE-001 - RTE-200). To change the name, follow the procedure shown below. 1. Press the MENU key to open the menu then select the [Routes] tab in the [Routes] menu. 2. Use the RotoKey to select a route. Push the key to show the Routes List pop-up menu. 3. Use the RotoKey to select [Rename] to show the [Rename] box. 4. Use the RotoKey to enter a new name.
5. ROUTES 5.8 How to Show or Hide All Routes All routes can be shown or hidden. An active route cannot be removed from the screen unless route following is stopped. 1. Long-push the RotoKey to show the soft controls. 2. Use the RotoKey to select [Routes]. 3. Use the RotoKey to select [Show] then push the key to show or hide all routes. 5.9 How to Follow a Route Before you follow a route, make sure that the path to the route is clear.
5. ROUTES 5.9.2 How to Follow a Route Selected from the Routes List 1. Press the MENU key to open the menu. 2. Open the [Routes-Routes] menu. 3. Use the RotoKey to select a route then push the key to show the Routes pop-up menu. 4. [Go To] is selected. Push the RotoKey. A red dashed line runs between current position and the point. This line is the course to follow to get to the point. The point arrival area is indicated with a circle, or both circle and line.
5. ROUTES 5.9.4 How to Show Information About a Route 1. Put the cursor on a route leg of the active route then push the right-click button to show the Routes pop-up menu. 2. Use the RotoKey to select [Route Info]. The display shows route information for the route selected. • Each route point name • Distances between points • Bearings between points • Time-to-go between points • Total distance • Bearing from the first to the last route points • Total time-to-go 5.9.
5. ROUTES 5.10 Operations When You Follow a Route 5.10.1 Restart Navigation When you follow a route, you can restart the navigation to the next point on the route from current location. When you steer to keep away from an obstruction or the vessel drifts, you go off course as shown in Line 1 in the figure. If you do not need to return to the original course, you can go to the point from the current position as shown in Line 2 in the figure. Line 2 Obstacle Line 1 Original course 1.
5. ROUTES 5.10.3 Stop Following a Route 1. Use the CursorPad to put the cursor on the dashed line of the route. 2. Push the right-click button to show the Route Follow pop-up menu. Restart Reverse Extend Route Route Info 3. Use the RotoKey to select [Cancel Route]. The arrival area, XTE alarm lines and set course are erased from the screen. The red lines turns blue. 5.10.4 Skip a Leg on a Route There are times when you do not need to follow all legs in an active route.
5. ROUTES 5.10.5 Waypoint Switching Mode When you reach a route point, your unit automatically changes to the next route point according to the waypoint switching mode selected on the menu. Cross Line: Change the waypoint when the vessel moves through an imaginary cross line (vertical line) that moves through the center of the destination point. Circle: Change the waypoint when the vessel comes within the circle. Cross Line & Circle: Change the waypoint when one of the above two conditions is met.
5. ROUTES 5.10.6 Route Auto Zoom You can get automatic range change after you have moved past a route point. Use this feature to find the next point in a route when the point is not within the current display range. 1. Press the MENU key to open the menu. 2. Open the [Routes-General] menu. 3. Use the RotoKey to select [Route Auto Zoom] then push the key to activate or deactivate the zoom. 4. Press the MENU key to close the menu. 5.10.
5. ROUTES 5.10.8 Waypoint Arrival Notification The waypoint notification feature releases audio and visual alarms when you are near a route point by some distance. You set the distance with [Switching Mode Circle Radius] on the [Routes] menu. Activate or deactivate this feature as follows. 1. Press the MENU key to open the menu. 2. Open the [Routes-General] menu. 3. Use the RotoKey to select [Waypoint Notification] then push the key to activate or deactivate this feature. 4.
6. RADAR This chapter provides the information necessary for radar operation. The topics include how to do the following. • Adjust the gain • Reduce sea and rain clutter • Measure the range and bearing to a target • Reduce radar interference • Expand echoes • Set a guard zone • Understand the radar display Your radar can be tuned automatically or manually and automatic is the default method. For manual tuning, see section 13.5.3. 6.
6. RADAR 6.2 How to Adjust the Gain The GAIN/TX key adjusts the gain (sensitivity) of the radar receiver. This key operates like the volume control of a broadcast receiver, which amplifies received signals. The correct setting shows some background noise on the screen. If you do not use enough gain, weak echoes are erased. If you use more gain than necessary, the background noise hides both weak and strong targets. Automatic gain adjustment 1.
6. RADAR 6.3 How to Reduce Sea Clutter The reflected echoes from waves appear at the central part of the display and have the name "sea clutter". The sea clutter increases in width as the height of waves and the height of the antenna above the water increase. If the sea clutter is strong, targets can be hidden inside the clutter, like in the left-hand figure shown below.
6. RADAR Manual sea clutter adjustment 1. Press the GAIN/TX key to show the Gain-Sea-Rain adjustment window. (You can also show the window if you put the cursor near the site of the window.) 2. Press the GAIN/TX key again to select [Sea]. 3. Rotate the RotoKey to adjust the sea clutter level. 4. Push the RotoKey to validate the setting and close the window.
6. RADAR 6.4 How to Reduce Rain Clutter When your vessel is in or near rain or snow, the reflections from the rain or snow appear on the screen. These reflections have the name “rain clutter.” When the rain clutter is strong, targets in or near the clutter are hidden in the clutter. Reflections from the rain clutter are easily identified from true targets by their wool-like echoes. The Rain control breaks the continuous display of echoes from the clutter into a random pattern.
6. RADAR 6.5 Range Scale The range setting controls the size of the area (in nautical miles, kilometers or statute miles) that appears on your display. The range ring interval is set automatically according to the range scale. This automatic selection allows for accurate range measurements on any range setting. The range and range ring interval appear at the top left-hand corner of the display.
6. RADAR 6.6 Orientation Mode The orientation mode controls the relationship between your vessel and all the other targets. The heading data is required in modes except the head-up mode. When the heading data is lost, the orientation mode automatically goes to head-up. A red “X” is also put on the compass icon on the status bar. Restore the compass signal to show the heading indication. Select the orientation mode again if necessary.
6. RADAR North-up Targets are shown at their measured distances and their true (compass) directions from your vessel. North is at the top of the screen. The heading line changes its direction according to your heading. True motion display Your vessel and vessels in motion move across the radar image at their correct speeds and positions (L/L). When your vessel gets near the edge of the screen, the vessel is automatically returned to the center of the screen.
6. RADAR 6.7 How to Measure the Range to a Target You can measure the range to a target three methods: • By the range rings • By the cursor (see section 1.10) • By the Variable Range Marker (VRM) Use the fixed range rings to get a rough estimate of the range to a target. These rings are the concentric solid circles about your vessel. The number of rings is automatically controlled by the selected range scale. The interval is displayed at the upper-left position of the screen.
6. RADAR 4. Push the RotoKey to finish. The VRM is then fixed at the range selected. 153 Target VRM1 + VRM2 VRM box 6.7.3 How to Deactivate a VRM 1. Push the RotoKey to show the soft controls. (In the default arrangement, a shortpush activates VRM1 and a long-push activates VRM1 and VRM2.) 2. Select [VRM] and [Clear 1] or [Clear 2]. The selected VRM and its indication are erased. You can also erase a VRM with the EBL/VRM pop-up menu.
6. RADAR 6.8 How to Measure the Bearing to a Target The Electronic Bearing Line (EBL) measures the bearing to targets. 6.8.1 How to Measure Bearing with an EBL There are two EBLs, No. 1 and No. 2. Each EBL is a straight dashed line from the center of the screen to the edge. The dashes of the No. 1 EBL are shorter than those of the No. 2 EBL. To measure the bearing to a target with an EBL: 1. Push the RotoKey to show the soft controls.
6. RADAR 6.8.2 How to Erase an EBL 1. Push the RotoKey to show the soft controls. (In the default arrangement, a shortpush activates EBL1 and a long-push activates EBL1 and EBL2.) 2. Select [EBL] and [Clear1] or [Clear2]. The selected EBL and the related EBL indication are erased. You can also erase and EBL with the EBL/VRM pop-up menu. Put the cursor in the EBL box then push the right-click button to show the EBL/VRM pop-up menu. Rotate the RotoKey to select the EBL then push the key to erase. 6.8.
6. RADAR 6.9 How to Off-center the Picture You can off-center your position to expand the view field without selecting a larger range scale. The position can be off-centered in the bow, stern, port or starboard direction, but not more than 75% of the range in use. To off-center the radar picture, operate the ScrollingPad. To return your vessel to the center of the screen, press the SHIP/3D button.
6. RADAR 6.10 Heading Line The heading line indicates your heading in all orientation modes. This line connects between your position to the outer edge of the radar display. The line is at zero degrees on the bearing scale in the head-up mode. The orientation of the line changes in the north-up, course-up and true motion modes with the movement of your vessel. To show or hide the heading line: 1. Put the cursor where there is no symbol then push the right-click button. The Radar pop-up menu appears. 2.
6. RADAR 6.11 How to Reduce Radar Interference Radar interference can occur when your vessel is near the radar of another vessel that operates on the same frequency band with your radar. The interference shows on the screen in many bright dots. The dots can be random or in the shape of dotted lines that run from the center to the edge of the display. You can identify the interference from the normal echoes, because the interference does not appear in the same location at the next rotation of the antenna.
6. RADAR 6.12 Guard Alarm The purpose of the guard alarm is to provide audio and visual warnings against targets (vessels, islands, landmasses, etc.) when a radar target enters the area you select. 6.12.1 How to Set a Guard Zone You can set a guard zone by two methods. Use the Radar pop-up menu or the soft controls ([Guard Zone]→[Zone] 1(2)). The procedure shown below shows how to set a zone with the pop-up menu. 1. Push the right-click button to show the Radar pop-up menu. 2.
6. RADAR 6.12.2 How to Activate or Deactivate a Guard Zone Put the cursor on a line of the guard zone. Push the rightclick button to show the Guard Alarm pop-up menu. Use the RotoKey to activate or deactivate the alarm. If a target enters the zone, the buzzer sounds and the message "Target enters Guard Zone 1 (or 2), Press Menu Button." appears in the text area. The audio alarm stops when you press the CANCEL key or MENU key.
6. RADAR 6.14 Echo Trails Echo trails show the movements of radar targets relative or true to your vessel in imitation afterglow. This function helps alert you to possible collision conditions. (a) True target trails (No smearing of stationary targets) 6.14.1 (b) Relative target trails Targets moving relative to own ship How to Hide or Show Trails Long-push the RotoKey to show the soft controls. Use the RotoKey to select [Echo Trail] then push the key to hide or show trails. 6.14.
6. RADAR 6.14.4 Echo Trail Reference Trail movement can be set for relative or true. The relative trails show the relative movements between targets and your vessel. True motion trails show the movements of targets according to the targets over-the-ground speeds and courses. True trails require position and heading information. 1. Press the MENU key to open the menu. 2. Open the [Radar-General] menu. 3. Use the RotoKey to select [Echo Trails] and trail reference. True Relative True 4.
6. RADAR 6.15 Echo Stretch The radar adjusts the reflected echoes from long-range targets, but the echoes are normally displayed weak and small. If you have a weak, long-range target that requires closer inspection, use the echo stretch to magnify the target. This function magnifies the targets and sea clutter and radar interference. For this reason, correctly adjust the sea clutter and radar interference before you activate the echo stretch. To activate or deactivate the echo stretch: 1.
6. RADAR 6.17 Automatic Shift The position of your vessel, or sweep origin, can be automatically moved to expand the view field without selecting a larger scale. The amount of automatic shift is calculated according to the speed of your vessel. The and the amount of shift is limited to 50% of the range in use. For example, the auto shift speed is 15 knots and the speed of your vessel is 10 knots. The amount of shift is then approximately 33%.
6. RADAR 6.19 How to Show, Hide, Cancel an Active Route You can show, hide or cancel the active route from the radar display. To hide or show the active route, long-push the RotoKey, then select [Active Rte]. Push the RotoKey to show or hide the active route. To cancel route navigation, set the cursor on the line that connects between the boat icon and the destination then push the right-click button. The "Cancel Route" pop-up appears. Push the RotoKey to cancel the route. Destination 6.
6. RADAR 6.21 Echo Color Echo color is available in single colors of yellow or green or “True.” True paints echoes in colors from red, green and yellow in the order of increasing echo strength. 1. Press the MENU key to open the menu. 2. Open the [Radar-General] menu. 3. Use the RotoKey to select [Echo Color]. 4. Use the RotoKey to select color desired. 5. Press the MENU key to close the menu. 6.22 Background Color Select the background color for daytime and nighttime operations. 1.
6. RADAR 6.24 Dual-Range Display The dual-range display scans and displays two different radar ranges at the same time, with a single antenna. There is no time delay between the two pictures and you have separate control of each picture. This feature lets you keep a close watch on close-range targets and far targets.
6. RADAR 6.25 FAR-2107 Radar Series and NavNet 3D The FAR-2107 radar series (program no. 02.50 or earlier, C specification) can be connected to your NavNet 3D, and some functions can be controlled from the NavNet 3D. The table shown below shows which features can be controlled from the NavNet 3D. Note that you should turn off Guard Polygon at the radar to control the radar from the NavNet 3D.
6. RADAR 6.26 How to Understand the Radar Display 6.26.1 False Echoes Echo signals can appear on the screen at positions where there is no target or disappear where there are targets. You can identify false targets when you understand why the false echoes appear. A description of false echoes follows. Multiple echoes Multiple echoes occur when a transmitted pulse returns from a solid object like a large vessel, bridge, or breakwater.
6. RADAR Shadow sector Funnels, stacks, masts, or derricks in the path of the antenna stop the radar beam. If the angle opposite the antenna is more than one or two degrees, a sector or shadow sector appears on the screen. Targets are not displayed within the sector. Radar antenna Radar mast Shadow sector Sidelobe echoes Each time the radar transmits, some radiation leaves on each side of the beam. This lost energy has the name "sidelobes.
6. RADAR 6.26.2 Search and Rescue Transponder (SART) A vessel in distress uses a radar-SART to show a series of dots on the radar display of nearby vessels to indicate distress. A SART transmits when it receives a radar pulse from any X-Band (3 cm) radar within a range of approximately 8 nm. When a SART receives a radar pulse, the SART transmits a response across all the radar frequency band. The SART first sweeps quickly (0.4 μs) through the band. The SART then slowly sweeps (7.
6. RADAR Racon (Radar Beacon) A racon is a radar transponder that sends a characteristic signal when the racon receives a radar pulse (normally only the three-centimeter band). If the racon signal is sent on the same frequency as that of the radar, the signal appears on the radar display.
6. RADAR 6.27 ARPA Operation The ARPA (Automatic Radar Plotting Aid) shows the movement of a maximum of 30 radar targets. The targets can be acquired manually or automatically. All 30 targets can be acquired manually when the ARPA acquisition area is not active. If the ARPA acquisition area is active, that total is equally divided between manual and auto acquisition. ARPA requires speed and heading data. WARNING No one navigational aid should be relied upon for the safety of vessel and crew.
6. RADAR 6.27.2 How to Manually Acquire a Target After you acquire a target, the radar marks the target with a broken square and a vector appears within 30 s. The vector indicates the direction of the target. Within 90 s after you acquire the target, the first tracking step is finished and the target is tracked continuously. At this point, the broken square changes to a solid circle. ARPA Symbol Meaning At acquisition of the target.
6. RADAR How to acquire a target for ARPA from the radar overlay display 1. On the radar overlay display, use the CursorPad to put the cursor on a target. 2. Press the right-click button to show the pop-up menu. 3. Use the RotoKey to select [Acquire Target] then push the key. 6.27.3 How to Display Target Data You can find the course, speed, range, bearing, etc. of an ARPA target. For simple data, put the cursor on the ARPA target.
6. RADAR 6.27.6 CPA/TCPA Alarm The CPA/TCPA alarm helps warn of possible collision conditions. The ARPA continuously monitors the predicted range at the Closest Point of Approach (CPA) and predicted time to CPA (TCPA) of each tracked target. When the predicted CPA or TCPA is less than their set values, the buzzer sounds and a text message appears. The ARPA symbol changes to a (red) triangle. This alarm helps you keep your vessel away from collision by warning of targets on a collision course.
6. RADAR 6.27.7 How to Set an ARPA Acquisition Area Any target that enters a ARPA acquisition area is acquired and tracked automatically. When a target leaves the area, the buzzer sounds. You can stop the buzzer with the CANCEL key. 1. On the radar display, push the right-click button to show the Radar pop-up menu. 2. Use the RotoKey to select [Set Guard 1] or [Set Guard 2], the guard zone to set. The cursor appears at the cursor location. 3.
6. RADAR How to erase the acquisition zone and return to full manual acquisition Put the cursor on a line of the guard zone then push the right-click button. (The line becomes thicker if correctly selected.) The Guard Zone pop-up appears. Use the RotoKey to select [Clear Guard]. 6.27.8 Track History Display The track of ARPA targets can be shown on the display with a line from the rear of the targets.
6. RADAR This page is intentionally left blank.
7. FISH FINDER This chapter describes the functions of the fish finder, which requires the Bottom Discrimination Sounder BBDS1, Network Sounder DFF series, ETR-6/10N or ETR-30N, or Color LCD Sounder FCV-1150. Many procedures in this chapter require you to open the “fish finder source menu.” This menu has the name [DFF1/BBDS1/DFF1-UHD], [DFF3/FCV], [ETR-6/10N] or [ETR-30N], depending on your system. Instead of writing all menu names, we write "fish finder source.
7. FISH FINDER 7.2 How to Select a Display Your fish finder has as many as seven display modes. These modes are single frequency, dual frequency, marker zoom, bottom zoom, bottom lock, A-scope, and bottom discrimination (requires Bottom Discrimination Sounder BBDS1 and specified transducer). 7.2.1 Single Frequency Display The single frequency display shows either the low-frequency or high-frequency picture on all the screen. Select a frequency according to your purpose.
7. FISH FINDER 7.2.2 Dual Frequency Display The dual frequency display provides both low- and high-frequency pictures. Use the dual frequency display to compare the same picture with two different sounding frequencies. The low-frequency picture is on the left, and the high-frequency is on the right. 0.0 High frequency Low frequency 36.8 Freq.
7. FISH FINDER 7.2.3 Zoom Displays How to activate a zoom display Push the RotoKey to show the soft controls. Select [Zoom], [Btm Lock], [Btm Zoom] or [Mkr Zoom] as necessary. Select [Off] to quit the zoom display and go to the single frequency display. How to change the active zoom display Click the zoom display selector icon (at the top-left corner) with the left-click button to change the active zoom display.
7. FISH FINDER Bottom-zoom display The bottom-zoom display expands the bottom and the fish near the bottom according to the zoom range selected on the [Fish Finder-fish finder source] menu. This display helps you find the density of the bottom. A bottom displayed with a short echo tail normally indicates the bottom is soft (sand bottom, etc.). A long echo tail indicates a hard bottom. Bottom zoom display Single freq. display 0.0 0 Bottom 40 20 Zoom marker 45.
7. FISH FINDER 7.2.4 A-scope Display (display only) The A-scope display appears at the right 1/16 of the screen and is available in any fish finder mode. This display shows the echoes at each transmission with the amplitudes and tone in balance with their intensities. This display helps you identify possible fish species and bottom structure. 0 Weak reflection (small fish or noise) 20 Fish echo Strong reflection (bottom) 46.
7. FISH FINDER 7.2.5 Bottom Discrimination Display The bottom discrimination display, available with the Bottom Discrimination Sounder BBDS1 and appropriate transducer, identifies probable bottom composition. The display is available in all screen divisions, single or dual frequency mode and occupies the bottom 1/6 of the screen in the full screen display. There are two types of bottom discrimination displays: standard and probability.
7. FISH FINDER Bottom discrimination display, probability mode Bottom discrimination window (4-color) Bottom discrimination display Mud (gray) Sand (orange) Gravel (red) Note: Above example does not contain gravel. Mud probability (Approx. 25%) Graph Sand probability (Approx. 25%) explanation Rocks (reddish-brown) Rocks probability (Approx.
7. FISH FINDER 5. Use the RotoKey to select [Mode] then push the RotoKey. 6. Use the RotoKey to select [Graphic] or [4 Color] then push the RotoKey. Graphic: Show the bottom discrimination window in graphic form. (Not available when [Bottom discrimination] is selected to [Probability].)4 color: Show the bottom discrimination window in 4 colors. 7. Use the RotoKey to select [Bottom disc window]. 8. Push the RotoKey to show or hide the bottom discrimination window. 9. Press the MENU key to close the menu.
7. FISH FINDER 7.4 Manual Fish Finder Operation Use the manual operation to see schools of fish and the bottom echo with a fixed gain setting. The gain, range and range shift functions let you select the depth you can see on the screen. The basic range provides a "window" into the water column and range shift moves the "window" to the depth that you select. 7.4.1 How to Select the Manual Mode Use the RotoKey to select [Auto] followed by [Off]. 7.4.
7. FISH FINDER 7.4.4 How to Adjust the Gain The gain controls how echoes of different strengths are displayed. Set the gain to show a slight amount of noise on the screen. Increase the gain for greater depths and lower the gain for shallow waters. Gain too high Gain proper Gain too low Press the GAIN/TX key to show the gain window. [Gain HF] is selected. Rotate the RotoKey to adjust the gain then push the key to set. The current level is shown on the bar, and the setting range is 0-100(%).
7. FISH FINDER 7.5 Picture Advance Speed The picture advance speed controls how quickly the vertical scan lines move across the screen. A fast advance speed expands the size of a school of fish horizontally on the screen. A slow advance speed shortens the school of fish. Use a fast advance speed to see the hard bottom. Use a slow advance speed to see the smooth bottom. Fast Slow 1. Press the MENU key to open the menu. 2. Open the [Fish Finder-fish finder source] menu. 3.
7. FISH FINDER 7.6 How to Reduce Interference Interference from other fish finders and electrical equipment appears on the screen as shown in the illustration. When these types of interference appear on the screen, use the interference rejector to reduce the interference. Three or four levels are available depending on the fish finder source. Turn off the interference rejector when there is no interference, so that you do not erase weak echoes.
7. FISH FINDER 7.7 How to Measure Depth, Time Between Locations You can measure the depth to an object with the VRM. Also, you can measure the time (elapsed time) from the right edge to a location. For example, you can measure how many minutes ago an echo appeared. To measure the depth or the time to a location, operate the CursorPad to put the VRM on the object to measure depth or time. Read the depth below the VRM and the time at the top of the screen.
7. FISH FINDER 7.8 How to Erase Weak Echoes Sediment in the water and reflections from plankton appear on the display in low-intensity colors. You can erase these weak echoes with [Color Erase] on the [Fish Finder-fish finder source] menu. Weak echoes 1. Press the MENU key to open the menu. 2. Open the [Fish Finder-fish finder source] menu. 3. Use the RotoKey to select [Color Erase]. 4. Rotate the RotoKey to select the percentage of colors to erase then push the RotoKey to validate your setting.
7. FISH FINDER 7.9 How to Equalize Echo Strength A school of fish at a depth deeper than a school of equal strength in shallow water appears in weaker colors. This condition is caused by the movement attenuation of the ultrasonic wave. To display the schools of fish in the same colors, use the TVG. The TVG automatically increases the gain with depth so that echoes of the same strength and different depths are shown in the same colors.
7. FISH FINDER 7.10 White Marker The white marker displays the selected echo color in white. Use this feature to distinguish fish near the bottom from the bottom echo. 1. Press the MENU key to open the menu. 2. Open the [Fish Finder-fish finder source] menu. 3. Use the RotoKey to select [White Marker]. White Light-blue Blue Green Yellow Orange Red Reddish-brown 4. Use the RotoKey to select the echo color to display in white. 5. Press the MENU key to close the menu. 7.
7. FISH FINDER 5. Use the RotoKey to set the start depth. Rotate the knob to set numeric then push the key to validate the setting. End depth (from bottom) Start depth (from sea surface) Alarm range Alarm range marker End depth (from sea surface) Start depth (from bottom) Scenario for fish alarm Scenario for bottom-lock alarm 6. Set the end depth in same method. 7. Press the MENU key to finish. 7.11.2 How to Activate or Deactivate the Alarm Fish alarm Push the RotoKey to show the soft controls.
7. FISH FINDER 7.12 ACCU-FISHTM The ACCU-FISHTM feature estimates the length of each fish and shows a fish symbol and depth value or fish length. This feature requires appropriate transducer and either Network Sounder BBDS1, DFF series or Color LCD Sounder FCV-1150. Application consideration • The information given by this feature is intended for reference only. • ACCU-FISHTM uses both low-and high-frequency echoes for the measurements regardless of the frequency mode in use.
7. FISH FINDER 7.12.1 How to Set ACCU-FISHTM 1. Press the MENU key to open the menu. 2. Open the [Fish Finder-DFF1/BBDS/DFF1-UHD, or -DFF3/FCV] menu as applicable. 3. Use the RotoKey to select [Measurement]. 4. Use the RotoKey to select [Accu Fish] to activate ACCU-FISHTM or [Off] to deactivate ACCU-FISHTM. 5. Select [Fish Info]. 6. Select [Fish Size] or [Depth]. Fish size or depth is displayed in red. 60 60 15 15 Solid (Small) Solid (Large) Striped (Small) Striped (Large) 7. Select [Info Size].
7. FISH FINDER 7.12.2 Fish Size Correction The fish size shown on the display can be different from the true fish. If the size is wrong, add an offset to the measured value to get accurate indication on the screen. Use the RotoKey to select [Fish Size Correction] on the [Fish Finder-DFF1/BBDS1/ DFF1-UHD, or -DFF3/FCV] menu. Rotate the RotoKey to set correction percentage then push the RotoKey. The setting range is -80% to +100%, in intervals of 10. Fish Size Correction Setting 7.
7. FISH FINDER 7.14 Fish Finder Menu Operation This section describes the fish finder functions not described in previous sections. 7.14.1 Fish Finder-General Menu Fish Finder Source: Select the name of the fish finder connected to the network. Day Background Color: Select the background color for use during daylight hours. The options are black, dark blue, light blue, and white. Night Background Color: Select the background color for use at nighttime. The options are black and dark blue.
7. FISH FINDER 7.14.2 Fish Finder-DFF1/BBDS1/DFF1-UHD, -DFF3/FCV, -ETR-6/10N and -ETR-30N Menus Range Setup ETR-6/10N, ETR-30N sub menu Note: The section belows provides only descriptions not previously mentioned. DFF3/FCV sub menu DFF1/BBDS1/DFF1-UHD sub menu DFF1/BBDS1/DFF1-UHD, DFF3/FCV, ETR-6/10N, ETR-30N Bottom Range Shift Area: Select the area where to show the bottom echo, when Auto Range is active.
7. FISH FINDER Transmit Rate: Change the pulse repetition rate, in 20 levels and Auto. Use 20 (highest power) in normal use. Lower the Tx rate in shallow waters to prevent second reflection echoes that appear between the surface and the bottom echo. Max automatically sets pulse repetition rate and pulse length according to depth. Auto automatically sets the transmit rate according to ship’s speed, and is inoperative when there is no speed data.
7. FISH FINDER 7.15 NavNet 3D and LCD Color Sounder FCV-1150 The FCV-1150 can be connected to your NavNet, and some functions can be controlled from the NavNet. The table shown below shows those features that can be controlled from the NavNet. This feature is available with the FCV-1150 software version 0252359-03.01 or higher.
7. FISH FINDER Function Controllable from NavNet RX band Yes Shift Yes Speed of sound No Split range Yes Tx line display, Tx line area No TX power 7-26 Remarks Set at FCV-1150 On/Off only TX pulse length Yes TX rate Yes Water temp.
7. FISH FINDER 7.16 Interpreting the Display Color bar The color bar at the left edge of the display shows the range of colors used to display different echo strengths. The top color (reddish-brown) is the strongest color and the lower colors the weaker colors. Use the bar as a reference to estimate the density of a school of fish, fish species and the hardness of the bottom. STRONG REDDISH-BROWN RED ORANGE YELLOW GREEN LIGHT-BLUE BLUE DEEP BLUE WEAK No Signal 49.
7. FISH FINDER Bottom characteristic The tail from a hard bottom is longer than the tail from a soft bottom, because the hard bottom reflects more of the ultrasonic pulse. An echo from shallow water gives a stronger reflection than the echo received from deep water. A longer bottom tail appears on slopes, because of the difference in travel time at both edges of the beam angle.
7. FISH FINDER Density of a school of fish If two schools appear with the same color at different depths, the one in deeper water is denser because the ultrasonic wave attenuates as it propagates and the school of fish in deep water tends to be displayed in a weaker color. Fish echo Less reddish (Sparse echo) Reddish (Dense echo) Difference in signal strength Strong echo Weak echo Plankton A plankton layer appears as a large amount of green or blue dots, and is a possible location for fish.
7. FISH FINDER Surface noise When the sea is rough or the vessel moves over a wake, surface noise can appear at the top of the screen. Surface noise Air bubbles in the water When the sea is rough or the vessel makes a quick turn, there can be blank spots in the bottom echo. See the illustration. These blank spots are caused by air bubbles which stop the movement of the sound wave. These air bubbles can occur with the low-frequency ultrasonic waves.
8. FILE OPERATIONS This chapter covers file operations, using SD cards. Topics include • How to import tracks, routes, points and user setup • How to export tracks, routes, points and user setup • How to manage files on the hard disk and an SD card • How to request and import update files Use SD cards whose capacity is 128 MB to 2 GB. (For downloading software updates from the NavNet homepage (www.navnet.com) the capacity should be 2 GB or better.
8. FILE OPERATIONS 8.2.1 Files Menu Description Import Points & Routes Import points and routes from an SD card. When you import points and routes from an SD card, all points and routes currently stored in the MFD are replaced with those on the SD card. Import Tracks Import track from an SD card. Use this function to create a route using past tracks. Like with Import Points & Routes, imported tracks are displayed with current tracks.
8. FILE OPERATIONS 8.3 Exporting Tracks, Points and Routes, User Setup When the capacity for track is reached, the oldest track is erased to clear space for new track. Points and routes cannot be entered when their related memories are full. If you need to save track, points and routes permanently, save them to a SD card. You can also save user settings to a SD card to use the settings on other MFD units. 1. Insert a blank formatted SD card in either card slot. 2. Press the MENU key to open the menu. 3.
8. FILE OPERATIONS 8.4 How to Import Tracks, Points and Routes, User Setup You can import tracks, points, routes and user setup to the hard disk of a NavNet unit. Use this feature to use the same data across the NavNet network. 1. Insert applicable SD card in either card slot. 2. Press the MENU key to open the menu. 3. Open the [Files] menu. 4. Select [Import Tracks], [Import Points and Routes] or [Import User Setup]. 5. Rotate the RotoKey to select [Yes] then push the key. 6.
8. FILE OPERATIONS 5. Use the RotoKey to select the file to delete the push the RotoKey. You are asked if you are sure to delete the selected file. 6. Rotate the RotoKey to select [Yes] then push the key to delete the selected file. 7. Press the MENU key to close the menu.
8. FILE OPERATIONS 8.6 How to Update the System Software You can download the current software and chart for the NavNet 3D from www.navnet.com, if you use the "request update file" feature. This feature saves the information (program and chart version numbers) about your system to a SD card. You load the file saved to the SD card on your PC and open the NavNet homepage. Follow the instructions on the homepage to check your software and chart version numbers.
8. FILE OPERATIONS 5. The data in the SD card is copied to the hard disk of the NavNet 3D. When the copy is completed. the software uploader is automatically updated. The message “Now Initializing” appears. It may take several minutes before you move to the next step. 6. The screen shows a list of the network components in your NavNet 3D system that need updating. You can select what to be updated in each session by marking in the checkboxes beside the listed network components.
8.
9. CAMERA/VIDEO The camera/video function allows you to use your unit to play back images from a video player, on-board camera, network camera or DVD player. Network camera images can be seen across the NavNet 3D network. A video signal can be seen only on the MFD that receives the video signal. A maximum of four IP cameras can connect to the Navnet system. You can monitor the images from four cameras on the full screen or the 1/4 screen.
9. CAMERA/VIDEO 9.2 How to Set the Video Display 9.2.1 How to Select the Input Source You can select the input source from the menu or with the RotoKey. Below is the procedure with the RotoKey. 1. Activate the camera mode then push the RotoKey. 2. Rotate the RotoKey to select [Vid Source] then push the RotoKey. The selections are as follows: 3. Select each input source (Input1 - Input4). 4. Push the RotoKey to select or deselect the input. 9.2.
9. CAMERA/VIDEO 9.2.3 How to Set the Cycle Period The default cycle period is five seconds. The cycle times of 10 and 30 seconds are available also. 1. Press the MENU key. 2. Open the [Camera] menu. 3. Use the RotoKey to select [Time Interval]. 4. Use the RotoKey to select a time interval. 5. Press the MENU key to close the menu. 9.3 How to Show Video ID You can show video ID at the top-left corner. Use the RotoKey to select [Video ID] then push the key to show or hide the video ID.
9. CAMERA/VIDEO 9.4 How to Adjust the Video Image 1. Long-push the RotoKey to show the soft controls that adjust the video signal. Soft controls for adjustment of video (Brightness, Colors, Contrast) 2. Rotate the RotoKey to select [Brightness], [Colors] or [Contrast] then push the key. 3. Rotate the RotoKey to adjust the slider bar then push the key to validate your setting. 9.5 How to Control an Axis IP Camera An AXIS IP camera can be controlled from the NavNet display.
10. INSTRUMENT DISPLAY The instrument display gives you a maximum of five navigation and environment displays: • Engine • Steering • True wind • Apparent wind • True wind and weather In the default arrangement, the instrument display is available when the number of hot pages (display selections) is nine or ten. (Select the number of hot pages on the on the [My NavNet-General] menu.
10. INSTRUMENT DISPLAY 10.1 How to Prepare the Hot Page The instrument display is available when the number of hot pages in the display selection window is nine or ten. Select the number of hot pages to display as in the procedure shown below. 1. Press the MENU key to open the menu. 2. Open the [My NavNet-General] menu. 3. Use the RotoKey to select [Hotpage Number]. 4. Use the RotoKey to choose [Nine] or [Ten] to enable the instrument display. 5. Press the MENU key to close the menu. 10.
10. INSTRUMENT DISPLAY 10.3 Selecting an Instrument Display You can show engine, steering, wind or wind/weather data in the instrument display if you have the related sensors. Select the data to display as follows: 1. Activate the instrument display then push the CTRL key to select the instrument display with the yellow cursor. 2. Push the RotoKey to show the soft controls for selection of an instrument display. 3. Rotate the RotoKey to choose desired display then push the key to validate your selection.
10. INSTRUMENT DISPLAY 10.4.2 Engine Display The engine display shows the information listed below. The engine must output engine data in NMEA 2000 format to show the engine data. • Abnormal engine temperature and engine trouble lamps • Tachometer • Oil pressure • Engine temperature • Boost pressure Engine-related warning lamps Temp (green): Lights for high engine temperature. Warning (red): Lights for engine trouble or than high temperature.
10. INSTRUMENT DISPLAY 10.4.3 Wind and Weather Display The wind and weather display shows • Wind direction • Air temperature • Wind chill temperature • Dew point temperature • Barometric pressure • Relative humidity • Wind speed and direction Analog true wind direction 64.40 Air temperature 39.65 Wind chill temperature 50.80 Dew point temperature 1013 Barometric pressure 120.6 23.0 Digital true wind direction +60.
10. INSTRUMENT DISPLAY 10.4.4 True Wind Display The true wind display provides digital and analog indications of true wind speed and angle, and heading. Analog true wind angle Analog and digital true wind speed Heading Digital true wind angle Angle (S: Starboard, P: Port) 10.4.5 Apparent Wind Display The apparent wind display provides digital and analog indications of apparent wind speed and angle, and heading.
11. SIRIUS WEATHER RECEIVER When connected to the Sirius Weather Receiver BBWX1, this MFD provides the weather information for your area and Sirius satellite radio services. Before you use the weather application: • Purchase the Sirius Weather Receiver BBWX1. • Purchase a Sirius weather service subscription. Contact Sirius Satellite Radio INC., for additional information. • Connect the BBWX1 and the MFD displays then turn on both of those units.
11. SIRIUS WEATHER RECEIVER 11.2 Weather Icons The table below shows the weather icons that appear on the Sirius Satellite Weather display. You can show or hide these icons from the [Weather] menu. Color Icon Buoy or CMAN sta. Pink Storm cast Dark yellow (recorded in last 0-5 min.) Medium yellow (recorded in last 5-10 min.) Light yellow (recorded in last 10-15 min.
11. SIRIUS WEATHER RECEIVER 11.3 Weather Menu The [Weather] menu adjusts the following weather-related items: • Overlay transparency • Color scale • Weather radar (US or Canada) • Standard weather data • Advanced weather data 11.3.1 Displaying the Weather Menu 1. Press the MENU key to open the menu. 2. Use the RotoKey to open the [Weather-Sirius] menu. 3. Use the RotoKey to select the weather item to show or hide. 4. Push the RotoKey to show or hide the item. 5. Press the MENU key to close the menu.
11. SIRIUS WEATHER RECEIVER 11.3.2 Weather Menu Description You can show sea surface temperature (SST), wave forecast and wind forecast together on the full screen display. In the split window configuration, only one can be displayed on either screen. Only one of the three can be shown in “plain color” when all three are displayed, and SST has priority. Overlay Color Transparency Adjust the level of transparency for the weather overlay. Select this item with the RotoKey then push the key.
11. SIRIUS WEATHER RECEIVER Precipitation indication on CANRAD Weather radar color Transparent (low precipitation) Light green Medium green Dark green Yellow Orange Light red Dark red Level (mm per hour) 0.00 to 0.20 mm/hr 0.21 to 1.00 mm/hr 1.01 to 4.00 mm/hr 4.01 to 12.00 mm/hr 12.01 to 24.00 mm/hr 24.01 to 50.00 mm/hr 50.01 to 100 mm/hr over 100.01 mm/hr Weather Data Wind Forecast Select how to show the wind forecast. There are two types of wind icon styles: Vane feathers and Plain colors.
11. SIRIUS WEATHER RECEIVER Sea Surface Temperature This data layer shows the temperature of the sea surface in shades of red and blue. Lower temperatures are in blue. Surface Features/Pressure Activate this feature to get surface pressure with meteorological symbols. Put the cursor on a surface pressure icon to show the name of the surface pressure.
11. SIRIUS WEATHER RECEIVER Advanced Weather Data Storm Tracks The storm track icons show major storms in your area. These storms include tropical disturbances, depressions, storms and cyclones, hurricanes, typhoons and super typhoons. These symbols are displayed in three different colors: Grey, historical; Redcurrent, and Orange, forecast.
11. SIRIUS WEATHER RECEIVER Storm Cell Cast You can find the direction and speed of a storm when you put the cursor on the icon. For additional information, press the left-click button.
11. SIRIUS WEATHER RECEIVER Lightning The lightning icons show where lightning has hit, within the last 5, 10 and 15 minutes. The fill color of the icon indicates when the lightning hit occurred. See the table below for color and period. The number of lightning bolt markers indicates the number of times lightning has hit. Lightning icons Description of lightning icons Lightning icon Color Period Orange Last 0-5 min. Medium yellow Last 5-10 min. Light yellow Last 10-15 min.
11. SIRIUS WEATHER RECEIVER City Forecasts City weather forecasts are available where city icons are shown. For simple information, put the cursor on the city icon ( button. ).
11. SIRIUS WEATHER RECEIVER Buoys You can check the historical or current weather information at buoys. For simple information, put the cursor on the buoy icon ( left-click button. ).
11. SIRIUS WEATHER RECEIVER 11.4 Weather Reports Marine zone forecasts, marine warnings, tropical information and weather alerts are sent to your unit. You can see those items on the [Weather] menu when you open the related sub men. Sirius sends warning messages to tell you about bad weather. You can see these messages when you open the [Weather-Alert] Box menu. 11.4.1 Marine Zone Forecast These forecasts cover the following areas, and are available at ranges 32 nm and less.
11. SIRIUS WEATHER RECEIVER 11.4.2 Marine Warning Display the marine warnings (US coastal or near shore). NO REPORT AVAILABLE FOR THIS MARINE ZONE. 11.4.3 Tropical Statement Below is an example of a tropical weather statement.
11. SIRIUS WEATHER RECEIVER 11.4.4 Marine WatchBox The message "Weather Alarm, Press Menu Button." appears on the status bar when a tornado or thunderstorm warning is received. To see the information about the warning, press the MENU key to open the [Alert Box] in the [Weather] menu. The message is opened in the [Alert Box]. A sample warning message is shown below. You can show or hide the [WatchBox] warning message with [Sirius Marine WatchBox] in the [Alarm-General] menu.
11. SIRIUS WEATHER RECEIVER 11.5 Sirius Satellite Radio The Sirius satellite radio provides round-the-clock, 100% commercial-free music from every genre plus sports, news, talk and comedy. To show the Sirius satellite radio screen, long-push the DATA/VOL key, or select [Sat Radio] with the RotoKey then push the RotoKey. • Use the ScrollingPad to select channel as shown below.
11. SIRIUS WEATHER RECEIVER This page is intentionally left blank.
12. AUTOMATIC IDENTIFICATION SYSTEM (AIS) 12.1 AIS Overview AIS is a system that continuously transmits the identification and position of your vessel to other nearby vessels. All such vessels also receive data from other AIS equipped vessels and display their positions and other relevant information. The AIS broadcasts this information over a VHF transceiver.
12. AUTOMATIC IDENTIFICATION SYSTEM (AIS) 12.3 AIS Target Symbols Symbol Target type Color Description AIS target Light-blue or Green*1 COG is marked on the symbol with a solid line and arrow. Dangerous AIS target Red The CPA and TCPA of a target put the target on a collision course. Lost AIS target Light-blue or Green*1 An AIS target becomes a lost target if a signal is not received from the AIS target for x* minutes.
12. AUTOMATIC IDENTIFICATION SYSTEM (AIS) 3. Use the RotoKey to select [Proximity AIS Target Alarm] then push the key to activate (status icon is green) or deactivate the alarm. 4. Use the RotoKey to set the alarm value at [Proximity AIS Target Alarm Value]. 5. Press the MENU key to close the menu. 12.5 How to Ignore AIS Targets In the default setting, all AIS targets within 12 nm from your vessel are shown on the display.
12. AUTOMATIC IDENTIFICATION SYSTEM (AIS) 12.6 How to Display Target Data The name, course, speed, range, bearing, etc. of an AIS target can be shown on the display. For simple data, put the cursor on an AIS target. For detailed data, put the cursor on the target then push the left-click button. Name COG/SOG CPA/TCPA Range/Bearing PEGASUS 56.2°T/6.8 kt 3 m/55m03s 6.366 nm/26.
13. HOW TO ADJUST SETTINGS After you understand the basic operating procedures of your equipment, you can set the equipment according to your needs • Set the equipment according to your system configuration. • Change how the equipment operates and displays information. All the adjustments are done from the menu. To restore the default settings for the selected sub menu, use the [Set Default] button that is provided on each sub menu.
13. HOW TO ADJUST SETTINGS 13.1 RotoKey The user can select how many soft controls to make available with the RotoKey in the chart plotter, radar, fish finder and camera modes. The three quantities are basic, standard and full. If those quantities do not meet your requirements, a “custom” set of keys is also available. The table below shows the soft controls available for use in the chart plotter, radar, fish finder and camera modes.
13. HOW TO ADJUST SETTINGS Control label Routes New List Reset Nav Skip WPT Cancel Nav Reverse Show Level 1 Control routes Animate Animate Countdown Ruler Ruler tool Tide Graph Sleep Function Create a new route. Show Routes list. Restart XTE. Skip waypoint on a route Stop following a route. Reverse route following direction. Show or hide routes now displayed. Animate weather or tidal current forecast. Start or stop countdown timer. Measure range and bearing between two points. Show tide graph.
13. HOW TO ADJUST SETTINGS Control label Guard Zone Zone 1 Zone 2 Clear 1 Clear 2 Targets ARPA AIS History Cancel All Clear Lost DSC Active Route Sleep Level 1 Control guard zones. Activate guard zone 1. Activate guard zone 2. Deactivate guard zone 1. Deactivate guard zone 2. Control ARPA and AIS targets. Show or hide ARPA display. Show or hide AIS display. Show or hide history display. Stop tracking on all ARPA targets. Clear lost ARPA target. Turn DSC message info on/off. Show or hide active route.
13. HOW TO ADJUST SETTINGS Soft controls available in the camera mode Control label Vid Source Input1 Input2 Input3 Input4 IP1 IP2 IP3 IP4 Vid Cycle Cycle1 Cycle2 Video ID Brightness Colors Contrast Sleep 13.1.1 Level1 Select video source. Input 1 Input 2 Input 3 Input 4 IP camera 1 IP camera 2 IP camera 3 IP camera 4 Select video switching cycle. Select video switching cycle 1. Select video switching cycle 2. Show or hide video ID. Adjust brightness of video image. Select number of colors to show.
13. HOW TO ADJUST SETTINGS 13.1.2 How to Set the RotoKey If the Basic, Standard or Full sets of soft controls are not acceptable, you can select the soft controls to use on the [My NavNet] menu. To use your selections, set RotoKey in the [My NavNet-General] menu to [Custom]. 1. Press the MENU key to open the menu. 2. Open the My [NavNet-General] menu. 3. Open the [Chart], [Radar], [Fish Finder] or [Instruments] sub menu as appropriate. For example, open the [Radar] sub menu. 4.
13. HOW TO ADJUST SETTINGS 13.2 Data Boxes The section 1.14 shows how to select the data to show in the data boxes. This section shows you set the boxes from the [DataBox] menu. 13.2.1 How to Set the Data Boxes 1. Press the MENU key to open the menu. 2. Open the [DataBox] menu. 3. Use the RotoKey to select [Data Box] 1-4 or [Cursor Data Box] then push the RotoKey. For example, select [Data Box 1].
13. HOW TO ADJUST SETTINGS 4. Select how to show data in the data box. Off: Turn off the data. Single: Display data individually. Split: Display two items per box. For example, SOG and COG show both of those data in one box. ("Pos" is a special example, because it is a two-line display.) 5. Use the RotoKey to select the [Data Box Value] combo box related to the data box number selected at step 3. 6. Use the RotoKey to select or deselect data as appropriate. 7.
13. HOW TO ADJUST SETTINGS 13.2.2 How to Show or Hide all Data Boxes You can show or hide all data boxes. Select [DataBox Display] at the bottom of the [DataBox-General] menu then push the RotoKey to show or hide all data boxes. You can also hide or show the data boxes with the DATA/VOL key. 13.2.3 How to Adjust Transparency of Data Boxes You can adjust the degree of transparency for the data boxes with the [Transparency] slider. The available degree of transparency is 0-80(%).
13. HOW TO ADJUST SETTINGS 13.3.2 How to Set a Hotpage This section shows how to set a hotpage. The procedure shown below describes how to put the radar, chart plotter and fish finder displays in a three-way split screen. 1. Press the DISP key to show the display selection screen. 2. Long-push the RotoKey to show the hotpage arrangement screen, shown below. Select display division. Select display. (Display availability depends on display division and system configuration.) 3.
13. HOW TO ADJUST SETTINGS 6. The yellow rectangle moves to the bottom-right 1/4 screen. Rotate the RotoKey to select a display (for example, the fish finder display) then push the key. Your arrangement of displays appears on the screen and the display selection window is updated according to your arrangement.
13. HOW TO ADJUST SETTINGS 13.4 Global Menu The [Global] menu has two sub menus for general setting of the equipment. The [Global-General] menu includes font size, brilliance settings, position format, etc. The [Global-Units] menu sets units of measurement for range, depth, height, speed, etc. 13.4.1 Global-General Menu The [Global-General] menu is where you can turn off the key beep, and select position format, time display format, font size, etc. See the next page for full description.
13. HOW TO ADJUST SETTINGS Global-General menu description Menu item Function Options Key Beep Activate or deactivate the key beep which ON, OFF sounds when a key (incl. RotoKey) is operated. Font Size Select the font for all indications, menus and the like. After you change the font size, the system is reset to use the new font. Small, Medium, Large Point Size Change the size of all icons.
13. HOW TO ADJUST SETTINGS 13.4.2 Global-Units Menu The [Global-Units] menu lets you select units of measurement for range, length, depth, height, sea surface temperature, speed, wind speed, air pressure, oil /boost pressure, and volume.
13. HOW TO ADJUST SETTINGS 13.5 System Menu The [System] menu has menus for general system settings, sensor calibration, radar, fish finder. 13.5.1 System-General Menu The [System-General] menu selects the language to use, sets the message window dwell time, shows the connection diagram, etc. Language: Select the language to use. See section 1.13. Message Window Dwell Time: Set the number of seconds to leave a message window open before the window is closed.
13. HOW TO ADJUST SETTINGS 13.5.2 System-Calibration Menu The [System-Calibration] menu lets you enter the offsets for external sensors (speed, wind, temperature) to show true values on the display. Draft: In the default setting, the fish finder shows the depth from the transducer. For depth from the surface, set the draft of your vessel here. Speed Through Water: If the speed indication is wrong, add an offset to the speed output by the speed sensor to get the correct speed indication.
13. HOW TO ADJUST SETTINGS 13.5.3 System-Radar Menu The [System-Radar] menu provides the radar functions like manual tuning, tx sector area (area of no transmission) and pulse length. Manual Tuning: If you require manual tuning, do the following: 1. Use the RANGE key to select the 24-mile range. 2. Press the MENU key to open the menu. 3. Open the [System-Radar] menu. 4. Turn off Auto Tuning. 5.
13. HOW TO ADJUST SETTINGS 13.5.4 System-DFF1/BBDS1/DFF1-UHD, -DFF3/FCV Menu cy Transmission: Turn transmission on/off. Leave on normally. Transmission Power: Interference can appear on the screen when the fish finder on your vessel and another vessel have the same TX frequency. To prevent this interference, lower your TX power and ask the other vessel to lower their TX power. The TX power is available in Off, Min, 1-10, and 10 provides the highest TX power.
13. HOW TO ADJUST SETTINGS can not identify the fish near the bottom from the bottom echo, increase the bottom level. For the DFF1/BBDS1/DFF1-UHD, set both of these items to “-20”. External KP: Turn on to sync with external keying pulse. Stc HF (LF): Delete unnecessary echoes (plankton, air bubbles, etc.) near the surface that hide the fish near the surface. The setting range is 0-10, and 0 is Off. “10” deletes unnecessary echoes from the surface to approximately 16 ft.
13. HOW TO ADJUST SETTINGS 13.5.6 System-ETR-30N Menu cy cy Stc HF (LF): Delete unnecessary echoes (plankton, air bubbles, etc.) near the surface. Use this feature to clear the surface of unnecessary echoes to look for surface fish. The setting range is 0-10, and 0 is Off. “10” deletes unnecessary echoes from the surface to approximately 16 ft. If the echoes near the surface are erased completely, decrease the Stc.
13. HOW TO ADJUST SETTINGS 13.6 My NavNet-General Menu This section provides the information for the items in the [My NavNet] menu that are not described in other chapters. XX.XX Off Off My NavNet Reminder The [My NavNet Reminder] tells you to check your [My NavNet] settings every 10 times you turn on the power. You can activate or deactivate this message. Demo Mode The demo mode helps you understand the features of your system.
13. HOW TO ADJUST SETTINGS To control the demo mode from the chart plotter display: 1. Right-click the chart plotter display to show the pop-up menu. 2. Use the RotoKey to select [Manual Mode] then push the key to activate or deactivate the demo mode. System ID and Version Show the ID and version number of your system.
13. HOW TO ADJUST SETTINGS 13.7 How to Control Charts This section shows you how to manage your chart catalog, from the [Chart-Data Catalog] menu. From this menu you can browse, update, add and delete charts. 13.7.1 How to View Your Charts 1. Press the MENU key to open the menu. 2. Open the [Chart-Data Catalog] menu. *1 *2 *3 Preview of chart selected from chart list. Chart list *1 Navnet ID *2, 3 One (chart) memory slot=2 GB. A total of 24 GB in the hard drive is allotted for charts. 3.
13. HOW TO ADJUST SETTINGS 13.7.2 How to Update Charts You can update the charts that you have on your hard disk from the NavNet web site www.navnet.com. 1. Put the SD card that contains the chart data into one of the slots in the card drive. 2. Press the MENU key to open the menu. 3. Open the [Chart-Data Catalog] menu. 4. Rotate the RotoKey to select the [Install data from SDcard] button then push the RotoKey. The message shown below appears. Application will now exit to perform data installation.
13. HOW TO ADJUST SETTINGS 13.7.3 How to Add a Chart You can purchase the charts for your area from the NavNet web site www.navnet.com. Download a chart to a SD card then follow the instructions in the procedure on this page. 13.7.4 How to Delete a Chart You can delete unnecessary charts from the hard drive. For example, you do not require a chart of Europe because you navigate along the US coastline. 1. Press the MENU key to open the menu. 2. Open the [Chart-Data Catalog] menu. 3.
13. HOW TO ADJUST SETTINGS This page is intentionally left blank.
14. MAINTENANCE, TROUBLE SHOOTING This chapter has information about maintenance and troubleshooting that the user can follow to care for the equipment. NOTICE WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified persons can work inside the equipment. 14.1 Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.
14. MAINTENANCE, TROUBLE SHOOTING 14.2 Fuses The Processor Unit (MPU-001) and the Display Control Unit (DCU12) have a fuse that protects them from high electric current and equipment fault. If you cannot turn on the power, check the fuse to see if it has blown. Find the reason for the blown fuse before you replace the fuse. If the fuse blows again after the replacement, contact your dealer for information. A wrong fuse can damage the equipment. WARNING Use the proper fuse.
14. MAINTENANCE, TROUBLE SHOOTING 14.4 How to Clean the Filter in the Processor Unit Clean the filter in the Processor Unit when the filter becomes dusty. Remove the filter and clean it with water and a mild detergent. Let the filter dry then set it to the Processor Unit. Filter 14.5 The Magnetron When the life of the magnetron is reached, the targets do not appear on the radar display.
14. MAINTENANCE, TROUBLE SHOOTING 14.6 Troubleshooting This section provides simple troubleshooting procedures which the user can follow to restore normal operation. If you cannot restore normal operation, do not check inside the unit. Have a qualified technician check the equipment. 14.6.1 General Troubleshooting Problem Remedy You can not turn on the power. • • • • • There is no response when a key is pressed. Turn off and on the power. If you do not get a response, the key is damaged.
14. MAINTENANCE, TROUBLE SHOOTING 14.6.3 Chart Plotter Troubleshooting Problem Remedy Position is not fixed. Check that antenna connector is fastened and navigator is correctly connected. The track of your vessel is not plotted. Check that the track is turned on. (Put the cursor on the boat icon to open the pop-up menu and check that "Tracks" is on.) 14.6.4 Fish Finder Troubleshooting Problem Remedy You selected a fish finder display with the DISP key, but no picture appears.
14. MAINTENANCE, TROUBLE SHOOTING 14.7 GPS Status Display The GPS status display shows the signal strength and location in the sky for each GPS satellite received. 1. Open the [System-General] menu. 2. Click the [GPS Status] button to show the GPS status display. 3. Push the RotoKey to close the display and return to the previous display. DOP 1 ALT +3.20 m • The date and time appear at the top-left corner of the display.
APPENDIX 1 MENU TREE Ship & Track MENU key 1 General Points General Routes General COG/SOG Predictor (On, Off) COG/SOG Predictor Time (0m10s, 0m30s, 1m00s, 2m00s, 5m00s, 10m00s, 15m00s, 30m00s) Heading Line (On, Off) Boat Icon Orientation (Heading, COG) Track Interval (Distance, Time) Distance Interval (00.01 - 99.
APPENDIX 1 MENU TREE 1 Chart General Photo Transparency on Water (0 - 80%) Popup Information (On, Off) Aerial View Bathymetry (On, Off) Depth Color Transparency (0 - 80%) Auto Depth Color Scale (On, Off) Depth Color Scale Style (Classic Hue, Blue Hue) Manual Depth Color Range (0 - 9000 ft) 3D Exaggeration (Very Low, Low, Medium, High, Very High) 3D Pan/Tilt Mode (On, Off) Auto Shift Maximum Speed (0.0 - 99.
APPENDIX 1 MENU TREE 1 Radar General Radar Source Echo Color (True, Green, Yellow) Echo Transparency for Overlay (0% - 80%) Day Background Color (Black, Dark Blue, White) Night Background Color (Black, Dark Blue, White) Own Ship Icon (On, Off) EBL Reference (Relative, True) Sweep Fade (On, Off) Watchman (Off, 5 m, 10 m, 20 m) Echo Trails (True, Relative) Echo Trails Time (15s, 30s, 1m, 3m, 6m, 15m, 30m, Continuously) Echo Trail Style (Multi Color, Single Color) Echo Trail Color (Blue, Yellow, Green) Auto
APPENDIX 1 MENU TREE 1 Camera Camera Data Box General Targets General Weather Sirius Scrolling Cycle 1 (Input1, Input2, Input3, Input4, IP1, IP2, IP3, IP4) Scrolling Cycle 2 (Same choices as Scrolling Cycle 1.
APPENDIX 1 MENU TREE 1 Alarm General Alarm (Off, Internal, External, Internal & External) Speaker Alarm Output (On, Off) Speed-Based Output (On, Off) Speed-Based Output Value (00.0 - 99.9 kt) External Alarm Input (Off, MOB, Save Point) XTE Alarm Value (000 yd - 999 yd) XTE Alarm (On, Off) Anchor Watch Alarm (On, Off) Anchor Watch Alarm Value (000 - 999 yd) Proximity Alarm (On, Off) Depth Alarm Value Depth Alarm (Off, Over, Under) (000 - 900 ft) SST Alarm Value or Shear (000.0°F - 150.
APPENDIX 1 MENU TREE 1 Global General Units Files 1 AP-6 General Key Beep (On, Off) Font Size (Small, Medium, Large) Point Size (Normal, Small, Big) Day/Night Mode (Day, Dusk, Night) Great Circle Navigation (On, Off) Bearing Display (True, Magnetic) Position Format (DDD.dddddd, DD°MM.mmmm, Loran C Station & GRI Loran-C, MGRS) (Select Loran C Station and GRI.) Time Zone (Select time zone.
APPENDIX 1 MENU TREE 1 System General Language (English and others) Message Window Dwell Time (0m05s - 1m59s) Connection Diagram GPS Status Installation Wizard Reset Default Settings Exit Menu Calibration Draft (-15.0 ft - +99.9 ft) Speed Through Water (-50% - +50%) Sea Surface Temperature (SST) (-99.9°F - +99.
APPENDIX 1 MENU TREE 2 1 Memory My Navnet Display Set Factory Default Radar Select Antenna Set Factory Default Fish Finder Exit Menu Select Fish Finder Set Factory Default General My Navnet Reminder (On, Off) Roto Key (Basic, Standard, Full, Custom) Hotpage Number (Five, Six, Seven, Eight, Nine, Ten) Boat Icon (A Simplified Icon, Commercial Fishing, Motor Boat Cruiser, Super Yacht, Sail Boat, Sport Fishing) Demo Mode (Off, Internal, External. For internal, select demo file.) Initial Speed (00.
APPENDIX 1 MENU TREE 2 3 Animate (On, Off) Countdown (On, Off) Ruler (On, Off) Tide Graph (On, Off) Sleep Radar 2 Tx Auto Sea Advanced Coastal North Up (On, Off) Head Up Course Up (On, Off) Head Up (On, Off) True Motion (On, Off) Auto Shift (On, Off) Filters Int Reject (On, Off) Stretch (On, Off) Average (On, Off) Rings (On, Off) Hdg Ln Off (On, Off) Echo Trail (On, Off) Clr Trail (On, Off) EBL EBL1 (On, Off) Clear 1 (On, Off) EBL 2 (On, Off) Clear 2 (On, Off) VRM VRM 1 (On, Off) Clear 1 (On, Off) VRM
APPENDIX 1 MENU TREE 2 Fish Finder Mode Auto Zoom HF (On, Off) LF (On, Off) Dual (On, Off) Fishing (On, Off) Crusing (On, Off) Off Btm Lock (On, Off) Btm Zoom (On, Off) Mkr Zoom (On, Off) Off Btm disc*1 (On, Off) *1 BBDS1 only A-Scope (On, Off) *2 BBDS1, DFF series, FCV-1150 only 2 Auto Range* (Off, On) Split Range*2 HF (On, Off) Temp (On, Off) LF (On, Off) Fish Alarm (On, Off) Off (On, Off) Sleep Instruments Steering (On, Off) Engine (On, Off) Wind & Wx (On, Off) True Wind (On, Off) App Wind (On, Of
FURUNO MFDBB SPECIFICATIONS OF MULTI FUNCTION DISPLAY MFDBB 1 PLOTTER FUNCTION 1.1 Display mode Course plot, NAV data, NAV instrument data*, Engine monitoring* 1.2 Projection Mercator 1.3 Usable area 85° latitude or below 1.4 Memory capacity Track: 10,000 points, Point: 2,000 points Route: 200 courses w/ 100 waypoints each 1.5 MOB 1 point 1.6 Language Chinese, Dutch, Danish, Finish, French, German, Italian, Japanese, Norwegian, Portuguese, Spanish, Swedish, UK/US 1.
FURUNO 3.3 MFDBB CAN bus PGN (NMEA2000) Input 059392/904, 060928, 061184, 065280, 126208/720/992/996, 127245/250/251/257/488/489, 128259/267, 129025/026/029/033/044/538/540/808, 130306/310/311/577/817/818/819/820 Output 059392/904, 060928, 061184, 126208/720/992/996, 127245/251/258, 128259/267, 129025/026/029/033/283/284, 130306/310/311/577/816/817/818/819 3.4 Ethernet I/O sentences Same as NMEA0183 format 4 DISPLAY CONTROL UNIT (DCU12) 4.1 Screen type 12.1-inch color TFT LCD, 246 x 184.
INDEX Numerics 3D display description ............................................... 3-1 exaggeration ........................................... 3-4 A ACCU-FISHTM considerations ....................................... 7-19 setting up............................................... 7-20 Adv Wx Data soft control........................... 3-8 Advanced weather data ............................ 3-8 Advanced weather overlay........................ 3-8 AIS hide, show .............................................
INDEX updating ...............................................13-24 vector .......................................................2-1 Chart-Vector menu...................................2-10 City forecasts .........................................11-10 Clutter (fish finder) ...................................7-11 COG/SOG predictor ...................................2-6 Color bar ..................................................7-27 Color erase (fish finder) ...........................
INDEX wind and weather .................................. 10-5 Interference fish finder............................................... 7-13 radar ...................................................... 6-15 K Key beep ............................................... 13-13 L Land features .......................................... 2-12 Language ..................................... 1-19, 13-15 Light description ...................................... 2-10 Light sectors.........................................
INDEX Range rings................................................6-9 Raster soft control ......................................2-1 RotoKey customizing .................................. 13-2, 13-6 description..............................................1-13 operation ................................................1-13 set selection ...........................................13-5 Route log..................................................5-15 Routes active route on radar ..............................
INDEX radar ...................................................... 14-4 True motion reset ...................................... 6-8 True wind display .................................... 10-6 Tuning, manual ..................................... 13-17 Tx sector blanking ................................. 13-17 U Units of measurement ........................... 13-14 Unknown object....................................... 2-12 V Vector chart bottom features .....................................
FURUNO Worldwide Warranty for Pleasure Boats (Except North America) This warranty is valid for products manufactured by Furuno Electric Co. (hereafter FURUNO) and installed on a pleasure boat. Any web based purchases that are imported into other countries by anyone other than a FURUNO certified dealer may not comply with local standards.
FURUNO Warranty for North America FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS warranty on products from the date of installation or purchase by the original owner. Products or components that are represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty period stated above.
FURUNO ELECTRIC CO., LTD. 9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, Japan Tel: +81 798-65-2111 Fax: +81 798-65-4200 Pub NO. DOC-961 EC Declaration of Conformity We FURUNO ELECTRIC CO., LTD.
