(Elemental Chlorine Free) The paper used in this manual is elemental chlorine free. Printed in Japan PUB.NO.
IMPORTANT NOTICE • No part of this manual may be copied or reproduced without written permission. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications are subject to change without notice. • The example screens (or illustrations) shown in this manual may not match the screens you see on your display. The screen you see depends on your system configuration and equipment settings.
SAFETY INSTRUCTIONS Safety Instructions for the Installer Safety Instructions for the Operator WARNING WARNING Do not open the equipment. Only qualified personnel should work inside the equipment. Do not open the cover unless totally familiar with electrical circuits and service manual. Do not disassemble or modify the equipment. Improper handling can result in electrical shock. Fire, electrical shock or serious injury can result.
TABLE OF CONTENTS FOREWORD ........................................................................................................ iii SYSTEM CONFIGURATION................................................................................ iv EQUIPMENT LISTS .............................................................................................. v 1. MOUNTING ....................................................................................................... 1 1.1 Display Unit.........................
FOREWORD A Word to the Owner of the MU-170C FURUNO Electric Company thanks you for purchasing the MU-170C 17” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers.
SYSTEM CONFIGURATION RGB Radar, Video Plotter, Navigator, Video Sounder, Scanning Sonar, etc. DVI 12-24 VDC FAR-21X7 series, etc. VIDEO (NTSC/PAL) CCD camera, Video cassette recorder, etc.
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Display Unit MU-170C - 1 Remote Controller Set* RMC-200 000-012-629 1 set Spare Parts* SP19-00401 001-416-700 1 set Installation Materials* CP19-00500 000-012-654 1 set Accessories* FP19-01001 001-416-740 1 set Remarks w/hard cover *: See packing list of this manual. Option Name Code No.
1. MOUNTING Refer to the outline drawing of this manual for mounting dimensions. Note: The face of the LCD monitor is made of glass. Handle it with care. 1.1 Display Unit The display unit may be mounted on a desktop (optional bracket kit required) or flush mounted in a panel. When selecting a mounting location, keep in mind the following points: • Locate the unit out of direct sunlight. • The unit weighs 7.5 kg (flush mounting) or 12.9 kg (desktop mounting).
Flush mounting See the outline drawing of this manual for mounting dimensions. CAUTION Hold the hard cover and display unit together when lifting the display unit. The display unit may fall out if only the hard cover is held. 1. Remove the hard cover and four cosmetic caps from the unit. 2. Using the paper template supplied, make a cutout in the mounting location. 3. Set the display unit to the cutout, and fasten it with four self-tapping screws (5x40, supplied as accessories).
Desktop mounting The display unit can be mounted on a desktop, using the optional bracket kit (Type: MU-170C Hanger, Code No.: 000-153-819). Contents of bracket kit Name Hanger L Hanger R Pole Hole plug Hex bolt (M10x30) Flat washer (M10) Spring washer (M10) Hex bolt (M5x25) Flat washer (M5) Spring washer (M5) Qty 1 1 1 2 2 2 2 4 4 4 1. Assemble two hangers and pole with two hex bolts (M10x30), spring washers and flat washers, and cover holes for hex bolts with the hole plugs. 2.
1.2 Remote Controller Setting battery 1. Open the back cover of the remote controller and set two batteries supplied. WARNING Ensure battery polarity is correct. Wrong polarity may cause the batteries to explode. 2. Close the back cover of the remote controller. Writing the device name on the label Write the device name (ex. “FCV-1200L”) for each “signal” name on the label supplied with the remote controller. Attach the label to the remote controller at the location shown below.
2. WIRING Connect external equipment to the MU-170C by referring to the drawing below, the table on the next page and the interconnection diagram in this manual. Note: The MU-170C does not have a “hot plug” function. Therefore, when the power switch of the MU-170C and the equipment connected to it are on, do not connect or disconnect the interconnection cable to prevent damage to equipment. ( )(+) Fuse Blue Red VIDEO3 TB-1 14AWG-2C-PVC *5M* (Supplied) VIDEO2 CCD camera, Video cassette recorder, etc.
Port, cable and connectable equipment Used cable Port Name TB-1 DVI-D RGB1 VIDEO1 000-154-337 Standard 000-149-054 Option 3COX-2P-6C 5M 000-146-500 Option 3COX-2P-6C 10M 000-146-501 Option Name Type Power cable DVI Cable 14AWG-2C-PVC *5M* DVI-D/D SINGLELINK5M Analog RGB Cable RGB2 Code No.
3. ADJUSTMENTS Adjust the MU-170C according to the equipment connected. 3.1 RGB/DVI Setting RGB1 and RGB2 screens can be adjusted independently. Also, DVI screen can be adjusted similarly. 1. Adjust the display currently selected, at the DISP selection window. (See section 4.3.) 2. Press the MENU key to show the main menu. The main menu disappears if there is no operation for one minute. 3. Press the ◄ or ► key to select RGB1, RGB2 or DVI as appropriate.
Menu item Function Available range Adjusts the image size horizontally. H_SIZE Horizontal size: Narrow (◄) ↔ Wide (►) Variable depending on signal type Adjusts the image size vertically. V_SIZE Vertical size: Narrow (◄) ↔ Wide (►) Adjusts the timing of sampling so that the flicker PHASE** 1-32 disappears and the text is clear. Increases or decreases contrast level. CONTRAST 1-64 Dark (◄) ↔ Bright (►) Moves the image position horizontally.
3.2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens can be adjusted independently. The picture-in-picture window for each can be adjusted similarly. Also, the size of the picture-in-picture window can be adjusted at VIDEO1 (2 or 3) setting menu. Picture-in-picture window Picture-in-picture window 1. Set to the display currently selected, at the DISP selection window. (See section 4.3.) 2. Press the MENU key to show the main menu. 3. Press the ◄ or ► key to select VIDEO1, VIDEO2 or VIDEO3 as appropriate.
3.3 Menu Window Setting 3.3.1 Adjusting the menu window The menu window can be moved and translucentized on the OSD (On Screen Display) menu. 1. Press the MENU key to show the main menu. 2. Press the ◄ or ► key to select OSD.
3.3.2 Changing the signal name You can change the signal name which is shown on the DISP selection window (page 16) and PIP selection window (page 17). It is useful to use the name of the device connected (ex. “FCV-1200L”). 1. Press the MENU key to show the main menu. 2. Press the ◄ or ► key to select OSD.
3.4 Remote Controller Setting A remote controller can be set to be operative with a specific display unit, in the case of multiple MU-170C display units. It is useful to label the display unit and the corresponding remote controller with same name. 1. Press the MENU key to show the main menu. 2. Press the ► key to select SYSTEM.
4. OPERATION 4.1 Controls Display unit MENU key Shows the main menu. DISP key Shows the DISPLAY selection window. Power key LED Optical sensor Arrow keys Select menu item. PIP key Shows the PIP selection window. BRILL key Shows the BRILL adjustment window. Display unit Power key Press the power key ( ) to turn the power on or off. Note: Even if the power switch is off, a small amount of current flows through the equipment.
Remote controller RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 PIP1 PIP2 PIP3 + MENU BRILL Remote controller Key name Function RGB1* Shows the RGB1 signal. RGB2* Shows the RGB2 signal. DVI* Shows the DVI signal. VIDEO1** Shows the VIDEO1 signal on the entire screen. VIDEO2** Shows the VIDEO2 signal on the entire screen. VIDEO3** Shows the VIDEO3 signal on the entire screen. PIP1*** Shows the VIDEO1 signal in the picture-in-picture window. PIP2*** Shows the VIDEO2 signal in the picture-in-picture window.
4.2 Adjusting Display Brilliance The display brilliance can be adjusted as follows. 1. Press the BRILL key on the display unit to show the BRILL adjustment window. This window disappears if there is no operation for five seconds. BRILL 50 BRILL adjustment window 2. Press the ◄ or ► key to adjust the brilliance (available range: 1 to 50). You can also adjust brilliance by pressing the BRILL key continuously. 3. Press the ▲ or ▼ key to close the window.
4.3 Choosing Source for Main Picture Choose the signal to display on the entire screen as follows: 1. Press the DISP key to show the DISP selection window. This window disappears if there is no operation for five seconds. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 DISP selection window 2. Press the ▲ or ▼ key to select a signal. You can also select the signal by pressing the DISP key continuously. RGB1-2: The signal from the chosen RGB port is displayed. DVI: The signal from the DVI port is displayed.
4.4 Choosing Source for Picture-in-Picture Choose the source for the picture-in-picture window as follows: Note1: The screen image on the picture-in-picture window can be switched automatically among VIDEO1, VIDEO2 and VIDEO3 at the interval specified. Set the PIP SW TIME on the OSD menu. For details, see “3.3.1 Adjusting the menu window”. Note2: The size of the picture-in-picture window can be adjusted on the VIDEO1, 2 and 3 menus. For details, see “3.2 VIDEO Setting”. 1.
5. MAINTENANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 5.1 Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good operating condition. • Check that the connectors at the bottom of the display unit are tightly fastened. • Check the ground wire and ground terminal for rust. Clean if necessary.
Fuse replacement The fuse in the fuse holder protects the equipment from internal fault. If the fuse blows, find the cause before replacing it. If the fuse blows again after replacement, request service. WARNING Use the proper fuse. Use of a wrong fuse can cause fire or damage to the equipment. Ship’s power source Rating of fuse 12 VDC 10 A 24 VDC 5A Battery replacement The remote controller has two AA batteries.
5.3 Clearing the Memory You may want to clear the memory to start afresh with default settings. You can do this as follows: 1. 2. 3. 4. Press the MENU key to show the main menu. Press the ► key to open the SYSTEM menu. Select DEFAULT RESET by arrow keys. Press the ► key to select YES. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 A A INFRARED REMOTE EXT BRILL CTRL OFF (OFF/ON) DEFAULT RESET YES All custom settings will be lost.
FURUNO MU-170C SPECIFICATIONS OF MULTI-PURPOSE LCD DISPLAY MU-170C 1 GENERAL 1.1 Display 17-inch SXGA color TFT-LCD, 338 x 270 mm 1.2 Brightness maximum: 1000 cd/m 2 , minimum: 2 cd/m 2 or less 1.3 Resolution 1280 x 1024 (SXGA) 1.4 Viewing Angle up/down: 75°, left/right: 80° 1.5 Input Signal RGB ports 2 ports, VESA (VGA, SVGA, XGA, SXGA), (0.7 Vp-p, Synchronization: TTL level) 2 DVI port 1 port, VESA (VGA, SVGA, XGA, SXGA) VIDEO ports 3 ports, NTSC/PAL, 0.
FURUNO ELECTRIC CO., LTD. 9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, Japan Tel: +81 798-65-2111 Fax: +81 798-65-4200 Pub NO. DOC-853 EC Declaration of Conformity We FURUNO ELECTRIC CO., LTD.
REMOTE CONTROLLER SET ACCESSORIES SPARE PARTS 001-416-740 FP19-01001 001-416-700 SP19-00401 999-999-113 100-315-270 100-292-801 19-024-1313-0 000-149-069 14-034-2075-1 RMC-200 (*) 1 1 1 1 1 FP19-01001 1 SP19-00401 RMC-200 (略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) (*)は、ダミーコードに付き、注文できません。 (*) THIS CODE CANNOT BE ORDERED.
A-2 CODE NO. 001-416-740 TYPE FP19-01001 19AX-X-9501 -0 1/1 MULTI-PURPOSE LCD DISPLAY 付属品表 MU-170C ACCESSORIES 番 号 NO. 名 称 NAME 略 図 OUTLINE 数量 Q'TY 用途/備考 REMARKS 5X40 SUS304 +トラスタッピンネジ 1 型名/規格 DESCRIPTIONS 4 SELF-TAPPING SCREW CODE NO. 000-150-749 19AX-X-9501 (略図の寸法は、参考値です。 FURUNO ELECTRIC CO .,LTD. DIMENSIONS IN DRAWING FOR REFERENCE ONLY.
A-3 CODE NO. 001-416-700 TYPE SP19-00401 SPARE PARTS LIST FOR SHIP NO. U S 19AX-X-9301 -0 1/1 BOX NO. P SETS PER VESSEL E MULTI-PURPOSE LCD DISPLAY MU-170C ITEM NO. NAME OF PART OUTLINE ヒューズ 1 QUANTITY PER VES 3 DUMMY CODE 999-999-111 ダミーコード 5A 125V 1 FUSE SPARE ダミーコード 1 FUSE REMARKS/CODE NO. WORKING PER SET 10A 125V ヒューズ 2 DWG. NO. OR TYPE NO. 3 DUMMY CODE 999-999-112 MFR'S NAME FURUNO ELECTRIC CO.,LTD. DWG NO.
Y.
Y.
C B A NOTE *1. SHIPYARD SUPPLY *2. OPTION *3. FITTED AT FACTORY. *4. USER SUPPLY 14AWG-2C-PVC,5m,φ10 3 TB-1 1 + 2 - VIDEO3 VIN GND VIDEO2 VIN GND VIDEO1 VIN GND RGB1 RED GREEN BLUE NC GND GND GND GND +5V_VGA VGA_CABLE NC SDA HSYNC_N VSYNC_N SCL DWG.No. APPROVED CHECKED *3 DVI-D Y. Hatai TAKAHASHI.T P P P P *2 DVI-D/D SINGLELINK5M 5m,φ7.1 *3 *2 Dsub15P(mini) 3COX-2P-6C,5/10m,φ8.5 E.
FURUNO MU-170C 17 型カラーLCD 表示器 MU-170C 仕 様 1.総合 (1) 表示器 17 型 SXGA カラーTFT LCD、338x270mm (2) 輝度 最大輝度 1000cd/㎡, 最小輝度 2cd/㎡以下 (3) 解像度 SXGA(1280x1024) (4) 視野角 上下:75°、左右:80° (5) 入力信号 アナログ RGB 映像信号 2 ポート: VESA 規格(VGA, SVGA, XGA, SXGA) (0.7 Vp-p, 同期:TTL レベル) DVI-D 1 ポート: VESA 規格(VGA, SVGA, XGA, SXGA) 複合映像信号 3 ポート: NTSC/PAL, 0.7 Vp-p(75Ω) 2.電源 DC12-24V: 6.0-3.
5.3 オールクリア オールクリアを行って内部の設定を工場出荷状態に戻すことができます。 1. [MENU]キーを押して、メニューを表示します。 2. ►キーを押して、[SYSTEM]を選びます。 3. ▲または▼キーを押して、[DEFAULT RESET]を選びます。 4. ►キーを押して、[YES]を選びます。 RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 A A INFRARED REMOTE EXT BRILL CTRL OFF (OFF/ON) DEFAULT RESET YES All custom settings will be lost. ←key: cancel →key: reset INFORMATION RGB1 : 1280x1024 fH: 80KHz RGB2 : 640x480 fH: 31KHz DVI : NO SIGNAL VIDEO1: NTSC VIDEO2: PAL VIDEO3: NO SIGNAL PROGRAM NO.: ***** fV: 75Hz fV: 60Hz SYSTEM メニュー 5.
ヒューズの交換 本機内に過電流が流れると、ヒューズホルダー内のヒューズが切れます。ヒューズが切れた場合、 交換する前に十分その原因を調べてください。 入力電圧 DC12V DC24V ヒューズの定格 10A 5A 電池の交換 電池が少なくなるとリモコンで操作できる距離 が短くなります。リモコンからの操作がしにくく なった場合は電池を換えてください。 注)リモコンの電池は、単三マンガン乾電池を 使用してください。 古い電池と新しい電池を混ぜて使用しな いでください。 LCD 交換の目安 寿命がくると、輝度が十分に上がらなくなります。LCD の寿命時間は、約 40000 時間です。 5.
5. 保守点検 5.
4.4 PIP ウィンドウの選択 PIP ウィンドウに表示させる入力信号を選びます。 注 1) [OSD]メニューの[PIP SW TIME]を「5∼20」に設定すると、PIP ウィンドウ上に VIDEO1、 VIDEO2、 VIDEO3 の映像を自動的に切り替えて表示することができます (3.3.1 項参照) 。 注 2) PIP ウィンドウのサイズは、それぞれ[VIDEO1]、[VIDEO2]、または[VIDEO3]メニュー で調整します(3.2 節参照) 。 1. RGB1、RGB2、DVI 画面のいずれかが表示されているときに、[PIP]キーを押します。 PIP 設定ウィンドウが表示されます。5 秒間キー操作を行わなければ、自動的にウィンドウ は消えます。信号名は変更することができます(3.3.2 項参照) 。 VIDEO1 VIDEO2 VIDEO3 OFF PIP 設定ウィンドウ 2. ▲または▼キーを押して、入力信号を選びます。 [PIP]キーを連続的に押しても選ぶことができます。 PIP ウィンドウを表示させたくないときは、[OFF]を選んでください。 3.
4.3 入力信号の選択 画面いっぱいに表示させる入力信号を選びます。 1. [DISP]キーを押して、入力信号ウィンドウを表示します。 5 秒間キー操作を行わなければ、自動的にウィンドウは消えます。 信号名は変更することができます(3.3.2 項参照) 。 RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 入力信号ウィンドウ 2. ▲または▼キーを押して、入力信号を選びます。 [DISP]キーを連続的に押しても選ぶことができます。 RGB1∼RGB2: RGB1∼RGB2 ポートからの信号を表示する。 DVI: DVI ポートからの信号を表示する。 VIDEO1∼VIDEO3: VIDEO1∼VIDEO3 ポートからの信号を画面いっぱいに表示する。 3.
4.2 輝度の調整 表示器の輝度を調整します。 注 1)輝度を絞りすぎると輝度ムラが発生しますが故障ではありません。 輝度を絞った状態で電源を切ると、次に電源を入れたときに画面に何も表示されませ ん。このときは[BRILL]キーを連続して押してください。 注 2) FAR-21X7 シリーズ(DVI 入力信号)の表示器として使用する場合、[SYSTEM]メニュー の[EXT BRILL CTRL]を[ON]に設定すると、FAR-21X7 シリーズの操作部から輝度の調整 を行うことができます。ただし、RGB1、RGB2、VIDEO1、VIDEO2、または VIDEO3 入力 信号に切り替えると、FAR-21X7 シリーズの操作部から輝度の調整は行えなくなります。 本機の[BRILL]キー、リモコンの[BRILL-]キーや[BRILL+]キーで輝度の調整を行って ください。 1. [BRILL]キーを押して、輝度調整ウィンドウを表示します。 5 秒間キー操作を行わなければ、自動的にウィンドウは消えます。 BRILL 50 輝度調整ウィンドウ 2.
リモコン RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 PIP1 PIP2 PIP3 + MENU BRILL リモコンのキー説明 キーの名称 説明 RGB1 RGB1 入力信号を表示する(PIP ウィンドウ*はそのまま残る) RGB2 RGB2 入力信号を表示する(PIP ウィンドウ*はそのまま残る) DVI DVI 入力信号を表示する (PIP ウィンドウ*はそのまま残る) VIDEO1 VIDEO1 入力信号を表示する(PIP ウィンドウ*は消える) VIDEO2 VIDEO2 入力信号を表示する(PIP ウィンドウ*は消える) VIDEO3 VIDEO3 入力信号を表示する(PIP ウィンドウ*は消える) PIP1** PIP ウィンドウ*に VIDEO1 入力信号を表示する ([PIP1]キーを押すごとに PIP ウィンドウがオン/オフする) PIP2** PIP ウィンドウ*に VIDEO2 入力信号を表示する ([PIP2]キーを押すごとに PIP ウィンドウがオン/オフする) PIP ウィンドウ*に VIDE
4. 取扱い 4.
3.4 リモコンの設定 複数の表示器を使用している場合、各リモコンは特定の表示器に対してのみ動作するように設定 する必要があります。リモコンを設定した後、それぞれ対応する表示器とリモコンに同じラベル を貼り付けてください。 1. [MENU]キーを押して、メニューを表示します。 2. ►キーを押して、[SYSTEM]を選びます。 リモコンの ID 表示器の ID RGB1 RGB2 DVI INFRARED REMOTE EXT BRILL CTRL DEFAULT RESET VIDEO1 A OFF NO VIDEO2 VIDEO3 OSD SYSTEM (OFF/ON) INFORMATION RGB1 : 1280x1024 fH: 80KHz RGB2 : 640x480 fH: 31KHz DVI : NO SIGNAL VIDEO1: NTSC VIDEO2: PAL VIDEO3: NO SIGNAL PROGRAM NO.: ***** fV: 75Hz fV: 60Hz SYSTEM メニュー 3.
3.3.2 信号名の変更 「RGB1」から「VIDEO3」の入力信号名を装置の名前等、判りやすい名前に変更できます。 変更した文字は、入力信号ウィンドウ(17 ページ参照)および PIP 設定ウィンドウ(18 ページ 参照)に表示されます。 1. [MENU]キーを押して、メニューを表示します。 2. ◄または►キーを押して、[OSD]を選びます。 RGB1 信号名 RGB2 H_POSITION V_POSITION TRANSLUCENT PIP SW TIME PIP SKIP DVI VIDEO1 15 37 OFF OFF OFF VIDEO2 VIDEO3 OSD SYSTEM (1 – 29) (1 – 37) (OFF/ON) (OFF, 5 – 20) (OFF, V1/V2/V3) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI = DVI_______ VIDEO1 = VIDEO1____ VIDEO2 = VIDEO2____ VIDEO3 = VIDEO3____ OSD メニュー 3.
3.3 メニュー表示の設定 3.3.1 メニューの調整 メニューの表示位置や表示方法を設定します。 1. [MENU]キーを押して、メニューを表示します。 2. ◄または►キーを押して、[OSD]を選びます。 RGB1 RGB2 H_POSITION V_POSITION TRANSLUCENT PIP SW TIME PIP SKIP DVI VIDEO1 15 37 OFF OFF OFF VIDEO2 VIDEO3 OSD SYSTEM (1 – 29) (1 – 37) (OFF/ON) (OFF, 5 – 20) (OFF, V1/V2/V3) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI = DVI_______ VIDEO1 = VIDEO1____ VIDEO2 = VIDEO2____ VIDEO3 = VIDEO3____ OSD メニュー 3. ▲または▼キーを押して、設定する項目を選びます。 4. ◄または►キーを押して、設定内容を調整します。 5.
設定項目の内容 項目 PIP_SIZE CONTRAST R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH 説明 PIP ウィンドウのサイズ調整 画面サイズ: 35mmx27mm(1)←→237mmx189mm(10) コントラスト調整 暗い(数値小)←→明るい(数値大) 赤色のレベル調整 赤色レベル:弱(数値小)←→強(数値大) 緑色のレベル調整 緑色レベル:弱(数値小)←→強(数値大) 青色のレベル調整 青色レベル:弱(数値小)←→強(数値大) 色温度調整(4 段階) 赤色レベルを強く(5500K)←→青色レベルを強く(8000K) 黒色伸張機能(黒に近い色を、より黒くする機能) 標準(OFF, 数値小)←→黒色を強調(数値大) 白色伸張機能(白に近い色を、より白くする機能) 標準(OFF, 数値小)←→白色を強調(数値大) 10 設定範囲 1∼10 1∼64 1∼64 1∼64 1∼64 5500K/6500K/ 7000K/8000K OFF, 1∼10 OFF, 1∼10
3.2 VIDEO1、VIDEO2、VIDEO3 信号の設定 VIDEO1、VIDEO2、VIDEO3 からの入力信号の表示方法を設定します。これらの入力信号は、ピク チャーインピクチャー(PIP)ウィンドウにも表示されます。PIP ウィンドウのサイズは、[VIDEO1] (または[VIDEO2]、[VIDEO3])メニューで設定します。 PIP ウィンドウ 1. 入力信号ウィンドウで設定する信号を選びます(4.3 節参照)。 2. [MENU]キーを押して、メニューを表示します。 3.
設定項目の内容 項目 説明 設定範囲 H_SIZE 水平方向のドット調整 画面の横幅: 狭まる(数値小)←→広がる(数値大) 入力信号による V_SIZE 垂直方向のライン数調整 画面の縦幅:狭まる(数値小)←→広がる(数値大) 入力信号による 水平方向のサンプリング位相調整 (入力信号をサンプリングするタイミングを調整) (数値を変更して文字等を見やすくする) 1∼32 CONTRAST コントラスト調整 暗い(数値小)←→明るい(数値大) 1∼64 H_POSITION 水平方向の画面位置調整 左に移動(数値小)←→右に移動(数値大) 1∼99(RGB1,2) 1∼50(DVI) V_POSITION 垂直方向の画面位置調整 上に移動(数値小)←→下に移動(数値大) 1∼40 R_LEVEL 赤色のレベル調整 赤色レベル:弱(数値小)←→強(数値大) 1∼64 G_LEVEL 緑色のレベル調整 緑色レベル:弱(数値小)←→強(数値大) 1∼64 B_LEVEL 青色のレベル調整 青色レベル:弱(数値小)←→強(数値大) 1∼64 TEMPERATU
3. 装備後の設定 本機に接続している機器に応じて、信号の設定を行います。 3.1 RGB1、RGB2、DVI 信号の設定 RGB1、RGB2、DVI からの入力信号の表示方法を設定します。 1. 入力信号ウィンドウで調整する信号を選んでおきます(4.3 節参照)。 2. [MENU]キーを押して、メニューを表示します。 1 分間キー操作を行わなければ、自動的にメニューは消えます。 3.
ポート、ケーブル、対応機種 使用するケーブル ポート名 名称 TB-1 電源ケーブル DVI-D DVI ケーブル RGB1 コード番号 標準/ オプション 000-154-337 標準 000-149-054 オプション 3COX-2P-6C 5M 000-146-500 オプション 3COX-2P-6C 10M 000-146-501 オプション 型式 14AWG-2C-PVC *5M* DVI-D/D SINGLELINK5M ア ナ ロ グ RGB ケーブル RGB2 VIDEO1 VIDEO2 VIDEO3 次のケーブルを用意してください。 ・コネクタの型式: RCA メタル(両端) ・ケーブル長: 最大 10m ・ケーブル: 2.
2.
1.2 リモコン 電池を入れる 1. リモコンの裏蓋を開けて、支給の電池(2 個)を入れます。 2.
卓上装備 卓上装備には、オプションのモニター用ハンガー1 式(型名: MU-170C 用ハンガー, コード番号: 000-153-819)が必要です。 モニター用ハンガー1 式の内訳 名 称 ハンガー左 ハンガー右 支柱 ホールプラグ 六角ボルト(M10x30) ミガキ平座金(M10) バネ座金(M10) 六角ボルト(M5x25) ミガキ平座金(M5) バネ座金(M5) 数量 1 1 1 2 2 2 2 4 4 4 1. 2 個のハンガー(左と右)と支柱を 2 本の六角ボルト(M10x30) 、ミガキ平座金、バネ 座金とホールプラグで組み立てます。 2. 組み立てたハンガーを 4 本の六角ボルト(M10、造船所手配)で装備場所に固定します。 注) 排気孔と吸気孔をふさぐような場所には、本機を取り 付けないでください。 3. 表示器のハードカバー、4 個のパネルカバーを取り外 します。 4. 4 本の六角ボルト(M5x25) 、ミガキ平座金、バネ座金 を使って、ハンガーに表示器を固定します。 5.
埋込み装備 1. 支給の型紙を使って、装備場所に穴を開けます。 2. 表示器のハードカバー、4 個のパネルカバーを取り外して、取付穴にはめ込みます。 3. 表示器本体の正面から 4 本の+トラスタッピンネジ(5x40,付属品として支給)で固定し ます。 注)六角ボルトを使用する場合、壁から 10mm 突出する長さのボルトを使用してください。 埋込み装備 4.
1. 取付け要領 本書の外寸図を参照してください。 注)LCD 管面は壊れやすいガラス素材でできています。強い衝撃や圧力を加えないでくださ い。 1.1 表示器 表示器は埋込み装備と卓上装備の 2 種類があります。 次の点を考慮して取付け位置を決めてください。 直射日光の当らない場所 表示器の重さに耐えられる場所(埋込みタイプ:7.5kg、卓上タイプ:12.
構成表 標準 名 称 LCD 表示器 リモコンセット* 予備品* 工事材料* 付属品* 型 式 MU-170C RMC-200 SP19-00401 CP19-00500 FP19-01001 コード番号 ― 000-012-629 001-416-700 000-012-654 001-416-740 数量 備 考 1 ハードカバー付き 1 1 1 1 *: 本書のパッキングリスト参照 オプション 名 称 ケーブル組品 モニター用 ハンガー1 式 リモコンセット 型 式 3COX-2P-6C 5M 3COX-2P-6C 10M DVI-D/D SINGLELINK5M コード番号 000-146-500 000-146-501 000-149-054 MU-170C 用ハンガー 000-153-819 1 RMC-200 000-012-629 1 vi 数量 備 考 1 ケーブル長 5m 1 ケーブル長 10m 1 ケーブル長 5m 内訳は 3 ページ参照
システム構成 対応機種 接続可能機種 解像度 信号形式 *2 アナログ、IF-8000 経由での接続 VGA*2 アナログ、IF-8000 経由での接続 VGA *2 アナログ、IF-8000 経由での接続 CSH-5L/8L XGA *2 アナログ FSV-24 SXGA アナログ VGA *2 アナログ FR-1500 MARK-3 シリーズ XGA *2 アナログ FR-21X5 シリーズ SXGA アナログ FAR-21X7 シリーズ SXGA DVI FCV-1200L/1200LM *1 FCV-1500L*1 CH-250/250S GD-280/380/680 NAVnet シリーズ VGA VGA *2 アナログ *1: 縦型は未対応。 *2: VGA、SVGA、XGA の信号を入力すると、縦横比が異なるため、円の縦横が歪んで楕円 で表示されます。このような場合は、[RGB1](または RGB2、DVI)メニューの[DISP MODE]を[NORMAL]に設定してください。ただし、その場合画面の上下が黒く切れて
はじめに このたびは、17 型カラーLCD 表示器 MU-170C をお買い求めいただき、誠にありがとうございま す。本機は、各種の魚群探知機、スキャニングソナーやレーダーなどの表示器として使用できま す。性能、耐久性共に安心して使用していただけるように設計していますので、この説明書をよ くお読みいただき、本来の性能を十分発揮させていただきますようお願い申し上げます。 本機の特徴 様々な機種に対応(FAR-21X7 シリーズ, NAVnet シリーズ, FCV-1200L/1200LM, CH-250/250S, CSH-5L/8L, GD-280/380/680 など) 高解像度表示[SXGA(1280x1024 ドット)] 輝度調整機能付き(最大輝度 1000cd/㎡, 最小輝度 2cd/㎡以下) (昼夜を問わず快適な明るさでご覧になれます) 横置き装備 ピクチャーインピクチャー機能 iv
目次 はじめに ................................................................... iv システム構成................................................................ v 構成表 ..................................................................... vi 1. 取付け要領 .............................................................. 1 1.1 表示器.................................................................... 1 1.2 リモコン.................................................................. 4 2. 結線 ...............................................
ii
安全にお使いいただくために [必ずお守りください] お使いになる人や他の人への危害、財産への損害を未然に防止するため、以下のことを必ずお守 りください。表示内容を無視して誤った使い方をしたときに生じる危害や損害の程度を、本書で は次の表示で区分し、説明していますので十分に気をつけてください。 WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside.
「このページは空白です。」
重要なお知らせ • 取扱説明書の一部または全部の転載、複写は著作権者である当社の許諾が必要です。無断転 載することを固くお断りします。 • 本書を紛失または汚損されたときは、お買い上げの販売店または最寄りの当社各支店・営業 所でお買い求めください。 • 製品の仕様ならびに取扱説明書の内容は予告なく変更することがあります。 • 画面に表示される内容は、システムの設定や動作状態によって異なります。したがって、本 書内に掲載してあるイラストは画面の表示と異なる場合があります。 • 本書は日本語を母国語とする方を対象に記載しています。 • 本機を、お客様が本書の内容に従わずに取り扱われたり、または当社および当社指定の者以 外の第三者により修正・変更されることに起因して生じる障害等については、当社は責任を 負いかねますのでご了承ください。