Installation Manual MULTI DISPLAY RD-30 SAFETY INSTRUCTIONS.................................................................... i SYSTEM CONFIGURATION ............................................................... ii EQUIPMENT LISTS ........................................................................... iii 1. INSTALLATION ............................................................................... 1 1.1 Installation of Display Unit ...................................................................
Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : 0798-65-2111 Telefax : 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : MAR. 2001 E1 PUB.No. IME-44130-E1 ( YOSH ) RD-30 : FEB.
SAFETY INSTRUCTIONS WARNING Do not open the cover unless totally familiar with electrical circuits and service manual. Improper handling can result in electrical shock. Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. CAUTION Ground the equipment to prevent mutual interference. Observe the following compass safe distances to prevent interference to a magnetic compass: Standard Steering Display unit 0.35 m 0.
SYSTEM CONFIGURATION FURUNO MENU ENT DISP DIM * RD-30 PWR Multi display RD-30 GPS receiver GP-310B Sensor FURUNO ENT MENU DIM DISP * RD-30 PWR Multi display RD-30 FURUNO ENT MENU DIM DISP * RD-30 PWR GPS receiver GP-310B Multi display RD-30 Sensor Navigator : Standard : Option ii Ship's mains 12-24 VDC
EQUIPMENT LIST Standard supply No. Name Type 1 Multi Display RD-30 - 1 2 Spare Parts SP14-02901 - 1 set 3 Installation Materials CP14-06000 - 1 set Accessories FP14-02801 4 Code No. Qty Remarks +Tapping screw (4 pcs) MJ-A7SPF0005-020 - 1 set Hard cover Optional supply No. Name Type Code No. Qty 1 Flush Mount Kit S OP20-17 000-040-720 2 Flush Mount Kit F OP20-29 000-041-405 3 Cable Assy.
This page is intentionally left blank.
1. INSTALLATION 1.1 Installation of Display Unit Mounting considerations The display unit can be installed on a tabletop, on the overhead, or in a panel (optional flush mounting kit required). Refer to the outline drawings at the end of this manual for installation instructions. When selecting a mounting location, keep in mind the following points: • • • • • • Locate the unit away from exhaust pipes and vents. The mounting location should be well ventilated.
Flush mounting There are two types of flush mount kits, F type and S type. For details, see the outline drawings at the back of this manual. F type Flush mount kit F (Type: OP20-29, Code No.: 000-041-405) No. Name Type Code No. Qty 1 Cosmetic Panel 20-016-1051 100-251-370 1 2 + Tapping Screw 5x20 SUS304 000-802-840 4 3 Hex Bolt M6x12 SUS304 000-862-127 2 4 Spring Washer M6 SUS304 000-864-260 2 Remarks 1. Make a cutout of 183 X 92 mm. 2.
1.2 Wiring The figure below shows where to connect cables on the rear of the display unit. GPS RECEIVER DISPLAY UNIT DISPLAY UNIT 1A FUSE (+ Line) Black POWER Ground (12-24 VDC) + Red CAUTION Ground the equipment to prevent mutual interference. Figure 1-2 Wiring Note: The fuse holder contains a spring which fixes the fuse. To prevent detachment of the spring, which would cause loss of power, tie the line as shown in Figure 1-3. Fuse holder + line (red) Tie here.
Grounding The display unit contains a CPU. While it is operating, it radiates noise, which can interfere with radio equipment. Ground the unit as follows to prevent interference: • • • The ground wire should be 1.25 sq or larger. The ground wire should be as short as possible. The signal ground and frame ground are separated, however the power line is not isolated. Therefore, do not connect the signal ground to the frame ground when connecting other equipment to a positive ground battery.
One Display Unit NMEA 0183 AUX FURUNO DIM DISP * RD-30 SENSOR POWER OUT ENT MENU IN/OUT NMEA 0183 PWR 12-24 VDC Two Display Units GP-310B AUX FURUNO No. 1 MENU ENT DISP DIM * AUX FURUNO No. 2 IN/OUT ENT MENU DIM DISP * IN/OUT RD-30 PWR RD-30 PWR Ship's battery 12-24 VDC Max. 20 m Note2 Three Display Units GP-310B AUX FURUNO No. 1 MENU ENT DISP DIM * RD-30 IN/OUT AUX FURUNO No. 2 MENU ENT DISP DIM * PWR RD-30 Max.
Note3: Turn on display units in sequential order. Note4: Refer to the following table to connect a sensor other than the GP310B. Do not exceed the maximum output current and the output voltage range. Ship’s Battery 12 VDC 24 VDC One RD-30 Maximum Output output voltage range current 300 mA 10.0-14.9 V 300 mA 21.0-30.5 V Two RD-30 Maximum Output output voltage current range 180 mA 9.2-14.4 V 180 mA 20.4-30.2 V Three RD-30 Maximum Output output voltage current range 60 mA 8.7-14.1 V 60 mA 20.4-30.
2. INITIAL SETTINGS This equipment can input and output navigation data to external equipment in IEC 61162-1 (NMEA 0183) format. Input data is output as raw data. For output setting, refer to the operator’s manual of the equipment. 2.
2.2 IEC 61162-1 (NMEA 0183) Input Data Sentences The AUX port has priority when the same data sentences are input at it and the IN/OUT port simultaneously.
2.3 Setting Input/Output The I/O SETUP menu sets up the IN/OUT and AUX ports on the RD-30. Additionally you can use this menu to output power to other display units, in case of multiple display units. Note: Note that the equipment can process data input at the rate of up to 430 characters/second. Some delay will occur when processing data input at a higher rate. 1. Press the [MENU] key once or twice to open the main menu. 2. Select I/O SETUP and then press the [ENT] key.
AUX PORT IN/OUT PORT APB BWC BWR DBK DBS DBT DPT : : : : : : : OFF OFFOFF OFF OFF OFF OFF OFF APB BWC BWR DBK DBS DBT DPT 00/08 : : : : : : : OFF OFFOFF OFF OFF OFF OFF OFF 00/08 Number of sentences currently turned on Figure 2-3 IN/OUT PORT and AUX PORT menu Note: Sentences currently being received are shown in reverse video. 6. Select sentence to output and then press the [ENT] key. Use or to scroll the display. OFF ON Figure 2-4 IN/OUT PORT and AUX PORT options 7.
1 2 GP-310B GP-310B AUX DIM DISP * ENT MENU POWER DIM DISP * RD-30 PWR DIM DISP * POWER RD-30 PWR IN/OUT Ship's battery 12-24 VDC IN/OUT: OFF AUX: OFF POWER OUT: ON Ship's battery 12-24 VDC IN/OUT: OFF AUX: OFF POWER OUT: ON ENT MENU POWER RD-30 PWR IN/OUT L/L FURUNO FURUNO ENT MENU AUX AUX L/L FURUNO L/L IN/OUT IN/OUT: AUX AUX: OFF POWER OUT: ON DEPTH TEMPERATURE AUX GPS L/L PLOTTER 3 FURUNO ENT MENU DIM DISP E/S * RD-30 PWR IN/OUT L/L DEPTH TEMPERATURE IN/OUT:
A-1 ＰＡＣＫＩＮＧ ＬＩＳＴ 14CJ-X-9851 -4 1/1 RD-30 N A M E ユニット O U T L I N E DESCRIPTION/CODE № Q'TY UNIT RD-30-E ﾏﾙﾁﾃﾞｨｽﾌﾟﾚｲ 1 MULTIDISPLAY 000-041-574 ** 予備品 SPARE PARTS SP14-02901 FGMB 1A 125V ﾋｭｰｽﾞ 2 FUSE 000-114-805 付属品 ACCESSORIES FP14-02801 20-016-1091-2 保護ｶﾊﾞｰ 1 COVER 100-297-032 工事材料 INSTALLATION MATERIALS CP14-06000 MJ-A7SPF0009-020 ｹｰﾌﾞﾙ組品MJ 1 CABLE ASSY. 000-145-612 5X20 SUS304 1ｼｭ +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 4 +TAPPING SCREW 000-802-081 3.
C B A FUSE(1A) FG 7 *3. FITTED AT FACTORY. *2. OPTION. *1. SHIPYARD SUPPLY. NOTE ＊３）コネクタは工場にて取付済み。 ＊２）オプション。 GND 6 BLK クロ +V RD‑H TD‑B 5 P 3 2 RD‑C YEL キ P TD‑A 4 BLU アオ 1 IN/OUT J1 ミドリ GRN アカ RED WHT *3 MJ‑A7SPFD Jan. 31 '03 Jan. 31 '03 DWG.No. 7 6 5 4 3 2 1 7 6 5 4 3 2 1 P P *3 MJ‑A7SPFD Y.
