Rev: 6 Pg. Pg. 22 –– 4: 4: NavNet NavNet TZtouch TZtouch MFD MFD Network Network Installation Installation (w/o: (w/o: NN3D) NN3D) Pg. Pg. 5: 5: MIXED MIXED NavNet NavNet TZtouch TZtouch MFD MFD and and NavNet NavNet 3D 3D MFD MFD Network Network Installation Installation Pg. Pg. 6: 6: DFF1 DFF1 Dip Dip Switch Switch Settings Settings Pg. Pg. 7: 7: DFF3 DFF3 Dip Dip Switch Switch Settings Settings Pg. Pg.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 NavNet TZtouch Installation Checklist TZtouch MFD Network Installation (without NN3D): Connect all TZtouch MFDs to the Ethernet Network. If a HUB101 is used, set the internal HUB DIP switches to OFF (HUB101 DIP Switches are OFF by Default). TZtouch MFDs do not use “power-on” synchronization. Note: If you use the internal HUB of the TZT14, realize that the HUB will only be able to relay Ethernet traffic when the MFD is turned ON.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 NavNet TZtouch Installation Checklist TZtouch MFD Network Installation (without NN3D): Once the TZtouch MFDs have started, press the “Home” button and touch “Menu” on each MFD to confirm that you see both a Radar and Sounder menu (assuming you have both a Sounder and a Radar connected to the Ethernet Network).
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 NavNet TZtouch Installation Checklist TZtouch MFD Network Installation (without NN3D): IMPORTANT: All NavNet TZtouch installations are REQUIRED TO HAVE AN APPROPRIATE HEADING SENSOR CONNECTED TO THE SYSTEM. Select the Sounder menu and choose the Sounder Source.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 NavNet TZtouch Installation Checklist Mixed TZtouch MFD & NN3D MFD Network Installations: Make sure the NN3D network is fully operational. (We strongly recommend that you update any existing NN3D MFDs with the latest software before integrating a new TZtouch MFD into a NN3D Network). Connect the TZtouch to the NN3D Ethernet network. Note: Leave the HUB101 Dip Switch setting to OFF on the port(s) used to connect TZtouch MFDs.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 DFF1 MODE Switch settings For connection to NavNet 1, VX2, NN3D & TZtouch The DFF1 comes defaulted to work with the NavNet 3D MFDs. If you are connecting the DFF1 to an original NavNet, NavNet VX2 or TZtouch only system, you need to change the MODE switches as shown below.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 DFF3 MODE Switch settings For connection to NavNet 1, VX2, NN3D & TZtouch The DFF3 comes defaulted to work with the NavNet 3D MFDs. If you are connecting the DFF3 to an original NavNet, NavNet VX2 or TZtouch only system, you need to change the MODE switches as shown below.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 PSU-012 / 013 Jumper location for TZT 9 / 14 Installations When the power supply unit PSU-012 / 013 is connected to the TZT 9 / 14, attach the shorting jumper (supplied) to J7 on the PWR Board.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 How to Update a DRS radar sensor using a TZT9 or TZT14 MFD display 1. Create the Program Update SD-Card A blank 128MB or larger SD Card is needed for the update. Furuno highly recommends using “SanDisk” SD Cards. a) Download the Zip File located under any DRS radar sensor software tab. b) Unzip the files on your computer. Open the folder you just unzipped. You will see a folder named “UPLOADER”. c) Insert an SD Card into your computer.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 2. Update Procedure (continued) f) If you don’t see the DRS listed after the initialization, proceed to the following steps: a. Power the DRS OFF and then back ON. This can be done by cutting the power to the PSU or by disconnecting and then reconnecting the power cable to the DRS. b. Wait for 2 minutes. c. Click “Scan” on the MFD to refresh the list. g) Click on “START” to begin to update the DRS.
FURUNO U.S.A., INC. Camas, WA (360) 834-9300 Denton, MD (410) 479-4420 DRS Radar Menu Reset After updating the software in an existing DRS Radar Sensor to version 1.16 or installing a new DRS Radar Sensor, the Radar Menu in the TZtouch MFD must be reset to default settings. Before you begin, confirm that the DRS Radar sensor and the TZtouch MFD display are properly connected, the TZtouch MFD display is powered on and there is a Radar selection option showing on the Home screen.