Owner's Manual

Activating a SiriusXM Subscription
Before you can activate the SiriusXM subscription, you must
have the Radio ID (Locating the SiriusXM Radio ID, page 3).
1
With the SiriusXM source selected, tune to channel 1.
You should be able to hear the preview channel. If not, check
the SiriusXM Connect Tuner and antenna installation and
connections, and try again.
2
Tune to channel 0 to locate the Radio ID.
3
Contact SiriusXM listener care by phone at [phone] or
go to www.siriusxm.com/activatenow to subscribe in the
United States. Contact SiriusXM by phone at [phone]
or go to www.siriusxm.ca/activatexm to subscribe in Canada.
4
Provide the Radio ID.
The activation process usually takes 10 to 15 minutes, but
can take up to an hour. For the SiriusXM Connect Tuner to
receive the activation message, it must be turned on and
receiving the SiriusXM signal.
5
If the service is not activated within the hour, go to
http://care.siriusxm.com/refresh or contact SiriusXM by phone
at 1-855-MYREFRESH (697-3373).
SiriusXM Controls
When in SiriusXM mode, select .
Presets: Opens the list of preset SiriusXM channels.
Category: Opens a list of channel categories.
NOTE: You can select and to view channels within a
category.
Parental Control Settings on the FUSION
NRX Remote Control
You can lock and unlock SiriusXM radio channels, clear all
locked channels, and change your passcode using a FUSION
NRX remote control.
When in SiriusXM mode, select > Parental.
Unlock: Unlocks the parental controls.
Lock/Unlock: Unlocks or locks channels.
Clear all Locked: Unlocks all locked channels.
Change PIN: Changes the parental passcode.
Locking a SiriusXM Channel Using the FUSION NRX
Remote Control
1
When in SiriusXM mode, select > Parental.
2
If necessary, select Unlock and Enter your passcode.
3
Select Parental > Lock > Channel.
4
Select a channel.
5
Select Parental > Unlock to lock the parental controls
(optional).
DAB Playback
When you connect a compatible Digital Audio Broadcasting
(DAB) module and antenna, such as the FUSION MS-DAB100A
to the FUSION MS-BB300 stereo, you can tune in to and play
DAB stations.
DAB broadcasts are not available in all regions. When the
stereo is not set to a compatible region, the DAB source is not
available.
Setting the Tuner Region
You must select the region you are in to receive DAB stations
properly.
1
Select > Settings > Tuner Region.
2
Select the region you are in.
Scanning for DAB Stations
Before you can scan for DAB stations, you must connect a
compatible DAB module and antenna (not included) to the
stereo. Because DAB signals are broadcast in select countries
only, you must also set the tuner region to a location where DAB
signals are broadcast.
1
Select the DAB source.
2
Select to scan for available DAB stations.
When scanning is complete, the first available ensemble
found begins playing.
NOTE: After the first scan is complete, you can select
again to re-scan for DAB stations. When the re-scan is
complete, the system starts playing the first station in the
ensemble you were listening to when you started the re-scan.
Changing DAB Stations
1
Select the DAB source.
2
If necessary, select to scan for local DAB stations.
3
Select or to change the station.
When you reach the end of the current ensemble, the stereo
automatically changes to the first available station in the next
ensemble.
Selecting a DAB Station from a List
1
Select the DAB source.
2
If necessary, select to scan for local DAB stations.
3
Select > Browse > Stations.
4
Select a station from the list.
Selecting a DAB Station from a Category
1
Select the DAB source.
2
If necessary, select to scan for local DAB stations.
3
Select > Browse > Categories.
4
Select a category from the list.
5
Select a station from the list.
DAB Presets
You can save your favorite DAB stations as presets for easy
access.
You can save up to 15 DAB-station presets.
Saving a DAB Station as a Preset
1
With the DAB source selected, change the stereo to a DAB
station.
2
Select > Browse > Presets > Save Current.
TIP: You can quickly save the selected DAB station as a preset
by holding .
Selecting a DAB Preset from a List
Before you can select a DAB preset from a list, you must save at
least one DAB station as a preset.
1
Select the DAB source.
2
Select > Browse > Presets > View Presets.
3
Select a preset from the list.
Removing DAB Presets
1
With the DAB source selected, select > Browse > Presets.
2
Select an option:
• To remove one preset, select Remove Preset, and select
the preset.
• To remove all presets, select Remove All Presets.
4 DAB Playback