Owner's Manual

ManualsBrandsFusion ManualsCar Audio & VideoStereoActive

1

2

3

4

5

6

7

8

9

5

Control

the

audio

playback

using

the

FUSION-Link

app

on

the

watch.

After

the

devices

are

paired,

they

connect

automatically

when

they

are

turned

on,

within

range,

and

the

app

is

open

on

the

watch.

A

1acnrng

~

e

U~IU

t"uck

I"\

II

nl

You

can

attach

the

puck

mount

to

a

flat

surface

using

the

included

adhesive

or

screws.

Refer

to

the

manual

for

the

item

on

which

you

are

mounting

the

puck

mount

for

information

about

the

preferred

mounting

style.

If

these

mounting

options

are

not

sufficient

for

your

mounting

surface,

go

to

www.stereoactive.com

for

more

mounting

accessones

.

Attaching

the

Puck

Mount

Using

Adhesive

NOTICE

Before

placing

the

adhesive

on

the

mounting

surface,

make

sure

that

the

location

and

orientation

are

correct.

It

is

extremely

difficult

to

remove

the

adhesive.

The

adhesive

and

puck

mount

cannot

be

reused

after

being

removed

from

a

surface.

Some

mounting

surfaces

might

be

damaged

after

removing

the

adhesive.

1

Select

an

appropriate

location

for

the

stereo.

Before

securing

the

puck

mount,

make

sure

it

is

oriented

in

the

preferred

direction.

2

Thoroughly

clean

and

dry

the

mounting

surface

using

a

mixture

of

water

and

isopropyl

alcohol.

The

mounting

surface

must

be

free

of

dirt,

debris,

wax,

or

coatings.

Quick

Start

Manual

3

Remove

the

backing

from

one

side

of

the

adhesive.

4

Press

the

adhesive

to

the

bottom

of

the

puck

mount.

5

Remove

the

backing

from

the

other

side

of

the

adhesive.

6

Carefully

orient

the

puck

mount,

and

press

the

puck

mount

firmly

onto

the

mounting

surface.

7

Allow

the

puck

mount

to

sit

at

room

temperature

for

72

hours.

NOTICE

Before

attaching

the

stereo

to

the

puck

mount,

allow

the

adhesive

to

bond

to

the

mounting

surface

for

72

hours.

Failure

to

allow

adequate

bonding

time

may

cause

the

mount

to

detach

from

the

surface,

which

could

result

in

damage

to

the

stereo

or

mount.

Attaching

the

Puck

Mount

Using

Screws

NOTICE

Before

screwing

into

the

surface,

check

with

the

manufacturer

of

the

item

on

which

you

are

mounting

the

puck

to

verify

that

screws

should

be

used.

Some

surfaces

are

too

thin

to

support

screws,

and

the

adhesive

should

be

used

on

these

surfaces.

1

Select

an

appropriate

location

for

the

stereo.

Before

securing

the

puck

mount,

make

sure

it

is

oriented

in

the

preferred

direction.

2

Using

the

puck

mount

as

a

template,

mark

the

location

of

the

holes.

3

Remove

the

mount.

4

Using

a

drill

bit

appropriate

for

the

mounting

surface,

drill

the

pilot

holes.

5