Owner's Manual

Enabling Standby Mode
You can enable standby mode to allow the stereo to be turned
on with a NMEA 2000
®
remote control.
NOTE: When the stereo is in standby mode, it continues to draw
current from the battery. The maximum current draw in standby
mode is 80 mA.
NOTE: You must enable standby mode to wake the stereo from
a NMEA 2000 remote control.
Select > SETTINGS > POWER OPTIONS > STANDBY
MODE.
The stereo now enters standby mode when you hold .
Audio Control
Adjusting the Volume
1
Turn the dial to adjust the volume.
2
If necessary, press the dial to switch between zones.
TIP: To control all zones at the same time, press the dial
repeatedly to select GLOBAL.
Muting the Stereo
1
Press .
2
Press again to un-mute.
Adjusting the Gain for an Auxiliary Device
You can adjust the gain for a connected auxiliary device to
achieve a volume level similar to that of other media sources.
You can adjust the gain in 1 dB increments.
1
Select an auxiliary source.
2
Select an option:
• To increase the gain, select .
• To decrease the gain, select .
NOTE: To achieve the best audio quality when using a
portable media player with headphone output, it may be
necessary to adjust the volume control on the media player,
instead of adjusting the gain.
Speaker Zones
You can group speakers in one area into a speaker zone. This
enables you to control the audio level of the zones individually.
For example, you could make the audio quieter in the cabin and
louder on deck.
You can set the balance, volume limit, tone, subwoofer level,
subwoofer frequency, and name for each zone, and configure
other zone-specific settings (Speaker Zone Settings, page 8).
Adjusting the Tones
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select TONE.
4
Turn the dial to adjust the level.
5
Press the dial to switch to a different tone.
Disabling the Loud Setting for a Zone
The LOUD setting maintains frequency response at low volumes
and increases perceived loudness at high volumes. This setting
is enabled by default in all zones.
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select LOUD to clear the check box.
Adjusting Additional Audio Settings for a Zone
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select MORE.
4
Select one or more options:
NOTE: Not all options are available for all zones.
• To limit the maximum volume output of this zone, select
VOLUME LIMIT, and adjust the level.
• To set the subwoofer level for this zone, select SUB
LEVEL, and adjust the level.
• To adjust the right and left speaker balance of this zone,
select BALANCE, and adjust the balance.
Adjusting the Subwoofer Filter
You can use the subwoofer filter setting to control the subwoofer
cutoff frequency for each zone, which can enhance the blend of
the sound produced by the speakers and the subwoofer. Audio
signals above the selected frequency are not passed to the
subwoofer.
NOTE: If a DSP setting has been applied to zone, this setting
cannot be changed on the stereo. You can view the DSP setting
for the optimal cutoff frequency as calculated by the DSP
controller, but cannot adjust it.
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select SUB. FREQ..
4
Select a frequency.
Synchronizing the Source and Zone Volume
Levels
You can synchronize the volume levels on one or all zones with
some source devices, such as a Bluetooth source.
1
Select > SETTINGS > ZONE > PHONE VOLUME ZONE
SYNC.
2
Select a zone or GLOBAL.
When you adjust the volume on the source device, the volume
on the selected zone is also adjusted.
DSP Settings
This stereo features digital signal processing (DSP). You can
select pre-configured DSP settings for FUSION
®
speakers and
amplifiers to optimize audio reproduction in their installed
locations.
All DSP settings are configured using the FUSION-Link
™
remote
control app (FUSION-Link Wireless Remote Control App,
page 9).
Configuring the DSP Settings
You must download and install the FUSION-Link remote control
app on your compatible Apple
®
or Android
™
device before you
can configure the DSP settings (FUSION-Link Wireless Remote
Control App, page 9).
You can configure the DSP settings to optimize the sound on
each zone with the installed speakers, amplifiers, and
environment.
1
Open the FUSION-Link remote control app on your
compatible Apple or Android device.
2
If necessary, select the stereo you want to configure.
3
Select SETTINGS.
4
If necessary, select the MUSIC SETTINGS tab.
5
Select Zone.
6
Select a zone.
7
Select DSP SETTINGS.
8
Configure the DSP settings as needed, depending on the
models of FUSION speakers and amplifiers connected to the
zone.
2 Audio Control