Installation Instructions

Connecting to Power Through an Ignition Switch
This method of connection is used most often on ski boats, wake boats, and
similar sport or recreational vessels where power to the engines is toggled
often. For these installations, a quick standby and faster startup time is
desired so that music can be stopped and begin playing again as quickly
as possible after restarting the engines. When in standby mode, the stereo
uses up to 200mA, and you should connect the power wires through a circuit
breaker or manual switch to avoid draining the battery when you are not
using the boat.
1 Consult this diagram to plan the wire connections.
Item Description Notes
Yellow wire
You must connect this wire to the same power
source as the ignition or ACC switch.
Red wire
You must connect this wire to the ignition or ACC
switch before you connect it to the same power
source as the yellow wire.
1 A fuse (not
included)
You must install this fuse on the red wire before
you connect the red wire to the ignition or ACC
switch.
Ignition or ACC
switch
Connecting the red wire to this switch allows the
stereo to enter a low-power standby mode when
you turn off the engines, so it can start up faster
when you turn on the engines again.
Black wire Ground (-)
15 A fuse (not
included)
This fuse is required if you are not able to
connect to power through a 15A circuit breaker
.
15 A circuit
breaker or manual
switch
If a circuit breaker is not available, you must
connect a 15A fuse on the yellow wire. You
should also connect the yellow wire to power
using a manual switch, so you can remove power
to the stereo when you are not using the boat.
2 Route all wires to the stereo wiring harness, the ignition or ACC switch,
the circuit breaker, and the power source as necessary.
Do not connect the wiring harness to the stereo until after you have made
all of the bare wire connections.
3 Install all of the necessary fuses on the red and yellow wires.
4 Connect the wiring harness to the stereo.
When you turn on the ignition switch, the stereo turns on along with other
accessory electronics. When you turn off the ignition switch, the stereo
enters a low-power standby mode.
NOTE: When you are not using the vessel for an extended period of time, you
should remove power to the stereo using the circuit breaker or other manual
switch on the yellow wire to avoid draining the battery.
喇叭區間
您可以將一個區域內的喇叭分組成幾個喇叭區間。 此可方便您控制個
別區間的音訊等級。 例如，您可以調低駕駛艙的音量，並調高甲板的
音量。
各區間的每個聲道 (左和右) 最多可並聯連接兩個喇叭。 一個區間使用
內建放大器可支援最多四個喇叭。
區間 1 和 2 由內建的放大器驅動。 若要針對區間 1 和 2 使用 RCA 線路
輸出和 RCA 超低音揚聲器輸出，您必須連接外部放大器。
區間 3 和 4 僅可作為線路位準輸出。 若要針對區間 3 和 4 使用 RCA 線
路輸出和 RCA 超低音揚聲器輸出，您必須連接外部放大器。
您可以設定每個區間的平衡、音量限制、音調、超低音揚聲器頻率和
名稱，以及配置其他區間專屬設定。
單區間系統佈線範例
喇叭
水密連接
使用線路輸出進行喇叭系統佈線
此圖表說明使用線路輸出將外部放大器和超低音揚聲器連接到音響區
間 2 的系統安裝。 您可以將放大器和超低音揚聲器連接到音響上的任
何或所有可用區間。
備忘錄： 您可以在使用區間 1 和 2 的線路輸出時，將喇叭連接至內部
音響放大器的喇叭連接線，不過調整音量會影響連接至內部放大器和
線路輸出的喇叭。 這可能會導致音量不平均。
區間 1 喇叭
水密連接
區間 2 喇叭
放大器開啟訊號線
您必須將這條線連接到與區間線路輸出連接的每個放大器。
已連接的放大器所使用的接地 (-) 必須與音響所使用的相同，此訊號
線才能正常運作。
接上電源且連接到區間 2 線路輸出的放大器
區間 2 線路輸出與超低音揚聲器輸出
每條超低音揚聲器纜線皆可為接上電源的超低音揚聲器或超低音揚
聲器放大器提供一個單聲道輸出。 您可能需要使用 RCA 分接器將此
連接至放大器。
超低音揚聲器
12 安裝指示
DRAFT