INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200
FUSION CULTURE TABLE OF CONTENTS • PROGRAMMING REMOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 4 There’s no point doing something if no one notices. We’ve always believed the way to make things happen is by getting noticed. From • ALARM FEATURES PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . pg 5 our product, to our demo cars, to our events, FUSION is about • ADJUSTING THE SENSITIVITY LEVEL . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMING REMOTES ALARM FEATURES PROGRAMMING: ALARM FEATURE “I” PROGRAMMING: 1. Turn the ignition switch ‘OFF/ON’ 3 times (within 15 seconds) and leave in the ON position. 2. Push the valet switch 3 times, and hold on the 3rd push until a long chirp is heard from the siren, and then release the valet switch. You are now in the remote programming mode. 3. Press and hold any button of the remote until the siren responds with a confirming chirp, this indicates the remote has been stored into memory. 1.
ALARM FEATURE “II” PROGRAMMING: ALARM FEATURE “III” PROGRAMMING: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 times (within 15 seconds), and leave in the OFF position. 1. Turn the ignition ‘switch ‘ON/OFF’ 3 times (within 15 seconds), and leave in the OFF position. 2. Push the valet switch 4 times and hold on the 4th push until two short chirps and one long chirp is heard, and then release the valet switch. You are now in the alarm feature ‘II’ programming mode. 2.
ADJUSTING THE SENSITIVITY LEVEL OF THE SHOCK SENSOR 1. Turn the ignition ‘switch ‘ON/OFF’ 3 times (within 15 seconds) and leave in the OFF position. 2. Push the valet switch 6 times and hold on the 6th push until three short chirps and one long chirp is heard, and then release the valet switch. You are now in the alarm feature ‘Shock Sensor’ programming mode. 3. Press and hold button for 2 seconds.
A: CENTRAL LOCKING DIAGRAMS B: 6 PIN MINI CONNECTOR WIRE HARNESS: (After market Door Motors) INSTALLING DOOR LOCK MOTORS (2 WIRE) Green/ white 12V Blue/ white 1. Violet Wire: Positive Door Pin Switch Input Blue/ red 2. Blue Wire: Instant Trigger Ground Input Green/ red 3. Green Wire: Negative Door Pin Switch Input 12V From ignition switch 5. Orange Wire: 200mA Grounded when armed 6. Red/White Wire: (-) 200mA Programmable Output Channel 3 / 2 Step Door Unlock. Blue/ yellow Green/ yellow 4.
POSITIVE TRIGGER DOOR LOCK SYSTEM 2 STEP DOOR UNLOCK WIRE CONNECTIONS FOR 5 WIRE ALTERNATING DOOR LOCKS + 12V M aster Locking Switch Green / white Blue / white Door Lock + 12V 87A 85 30 Door unlock Green / yellow OEM Door Master Lock 87 86 Red / White + 12V +12V Unlock Lock x Cut the Unlock Wire Blue / yellow Green / Red x Green / White 6-Pin Door Lock Wire Harness ALTERNATING DOOR LOCKS Green/ white Blue/ red Blue/ yellow Blue / Red OEM Slave Door Lock Switch Unlock OEM Driver's
2 STEP DOOR UNLOCK WIRE CONNECTIONS FOR POSITIVE SWITCHED DOOR LOCKS +12V 87 Unlock 86 6-Pin Door Lock Wire Harness Power supply: Operating temperature: TX Frequency: OEM Door Master Lock Red / White 87A 30 Lock Existing Pos. Unlock Wire + 12V Existing Pos.
• • Specifications and design are subject to change without notice • •
