16IZ Radio System Manual - Full

121
→ GO to TABLE OF CONTENTS
The dedicated mixes, etc. usable when airplane
or glider model type is selected are displayed
in this Model menu functions section. First use
the Model type function of the Linkage menu to
preset the model type, wing type, and tail type
matched to the fuselage used. Other settings reset
the data used in mixing function, etc.
These dedicated mixes can be set for each
flight condition, as required. When you want to
use the system by switching the settings for each
condition by switch or stick position, use the
Condition select function to add ight conditions.
(Up to 8 conditions can be used)
Note: The T16IZ is designed so that the airplane and
glider model types can handle aircraft of the same
wing type.
The functions common to airplanes and gliders,
except some dedicated functions, are summarized
without regard to the model type.
The setting items are different, depending on the
number of servos, etc. according to the wing type
used. The setup screens in the instruction manual
are typical examples.
MODEL MENU (Airplane/Glider functions)
Model menu (Airplane/Glider) functions table
Servomonitor
Displays the servo test and operation position
Conditionselect
Flight conditions addition, deletion, copy, condition renaming, and condition
delay can be set.
AFR
Sets the angle and curve of all the operation functions.
Dualrate
D/R curve which can be switched with a switch, etc. can also be added.
Program.mixes
Program mixing which can be freely customized. Up to 10 mixes can be used for
each condition.
Ailerondi󱐯erential
This function adjusts the left and right ailerons. Roll axis correction and fine
tuning with a VR are also possible. This is convenient when making settings
during ight.
[Airplane/glider, 2 ailerons or more]
Flapsetting
The aps can be adjusted independently. For a 4 aps model, the camber aps
can be mixed with the brake aps.
[Airplane/glider, 2 aps or more]
AIL →Camberap
This mix operates the camber flaps in the aileron mode. It improves the
operation characteristic of the roll axis.
[Airplane/glider, 2 ailerons + 2 aps or more]
AIL →Brakeap
This mix operates the brake aps in the aileron mode. It improves the operation
characteristic of the roll axis.
[Airplane/glider, 4 aps or more]
Aileron →Rudder
This mix is used when you want to operate the rudder at aileron operation.
Banking at a shallow bank angle is possible.
[Airplane/glider, general]
Elevator → Camber
This mix is used when you want to the mix camber aps with elevator operation.
Lifting force can be increased at elevators up.
[Airplane/glider, 2 ailerons or more]
Cambermixing
This mix adjusts the camber and corrects the elevators. [Airplane/glider, 2 ailerons or more]
Airbrake →ELE
This mix is used to correct operation of the airbrakes (spoilers) when landing.
[Airplane/glider, general]
Camberap → ELE
This mix is used to correct for attitude changes when the camber aps are being
used.
[Airplane/glider, 2 ailerons + 1 ap or more]
Rudder → Aileron
This function is used to correct roll knife edge, etc. of stunt planes. [Airplane/glider, general]
Rudder → Elevator
This function is used to correct roll maneuvers, knife edge, etc. of stunt planes.
[Airplane, general]
Buttery(Crow)
This function is used when powerful brake operation is necessary. [Glider, 2 ailerons or more]
Trimmix1/2
The ailerons, elevators, and flaps trim offset rate can be called by switch or
condition selection.
[Glider general]
Snaproll
This function selects the snap roll switch and adjusts the steering angle of each
rudder. Servo speed can also be adjusted.
[Airplane general]
Airbrake
This function is used when airbrakes are necessary when landing or when diving,
etc. during ight.
[Airplane, general]
Gyro
This is a dedicated mix when a GYA Series gyro is used. [Airplane/glider/multicopter, general]
Ailevator
This function adjusts the elevators and ailerons of models with elevator
specications.
[Airplane/glider, elevator specications]
Acceleration
Allows a brief "overload" in response to sudden Elevator, Elevator → Camber,
and Ail → Rudder.
[Airplane/glider general]
Motor
The operation speed when the motor of F5B and other EP gliders is started by
switch can be set.
[Airplane/glider, general]
V-Tail
This function adjusts the elevators and rudder of V-tail models. [Airplane/glider, V-tail specications]
Winglet
This function adjusts the left and right rudders of winglet models.
[Airplane/glider, winglet specications]