Owner manual

ManualsBrandsFutaba ManualsHardwareFX-40

How to change the frequency/How to set ID

The FX-40 system has employed the frequency

synthesizer scheme. The FX-40 transmitter will set

the frequency of the R5014DPS (PCMG3 receiver)

by the wireless data transmission. When you are

using a new PCMG3 receiver and changing the

frequency, set ID or frequency by the following

instructions.

In case of using PCMG3 receivers

*Make sure that PCM-G3 is set as a modulation scheme.

Then change the frequency by the following instruction.

How to change the frequency

7XUQRQWKHSRZHURIWKHWUDQVPLWWHU

3XVKWKHDUHDWKDWVKRZVWKHIUHTXHQF\LQ

WKHKRPHVFUHHQRUSXVKWKH)UHTXHQF\

EXWWRQLQWKH/LQNDJHPHQX7KHQWKH

)UHTXHQF\6HWVFUHHQZLOOSRSXS

3XVKWKH5HFHLYHU,'EXWWRQ7KHQ,'

LQSXWWLQJVFUHHQIRUUHFHLYHUZLOOSRSXS

,QSXWWKHHLJKWGLJLW,'FRGHDWWDFKHGWRWKH

UHFHLYHUVFDVH3XVKWKH<HVEXWWRQDIWHU

FRQÀUPLQJWKH,'

*Use the "BS" button to move back digit by digit for

correction if you made a mistake. If you want to stop

changing ID code halfway, push "Return" button to return to

the previous screen.

*Once you set the ID code for a receiver, you don't have to set

the ID code again as long as you change the receiver itself.

*When you need to use two receivers for a large size aircraft,

you need to enter different ID codes to those receivers

respectively.

3XVKWKH%DQG12)UHTXHQF\EXWWRQLI

\RXQHHGWRFKDQJHWKHIUHTXHQF\7KHQ

\RXZLOOVHHIUHTXHQFLHVRQWKHVFUHHQ6HOHFW

WKHIUHTXHQF\\RXZDQWXVH3XVKWKHEXWWRQ

<HVDIWHUFRQÀUPDWLRQ7KHQ\RXZLOOVHHWKH

&RQÀUPDWLRQRIWKHFKDQJHER[

*If you have changed the module prior to turning on the

SRZHUFRQ¿UPDWLRQVFUHHQZLOOSRSXSWRDVN\RXZKHWKHU

you want to change the frequency. Push the button "Yes" to

change the frequency.

,IWKHIUHTXHQF\LVFRUUHFWSXVKWKHEXWWRQ

<HV7KHQ\RXZLOOVHHWKHPHVVDJH

7UDQVPLWWLQJWKHIUHTXHQF\GDWD,WWDNHVD

FHUWDLQWLPHWRVHQGWKHQHZIUHTXHQF\GDWD

WRWKHUHFHLYHUZLWKDVRXQG,I\RXQHHGWR

UHVHQGWKHGDWDSXVKWKH5HVHQGEXWWRQ

7XUQRQWKHSRZHURIWKHUHFHLYHUZKLOHWKH

QHZIUHTXHQF\GDWDLVGLVSOD\HG:KHQ

WKHIUHTXHQF\VHWWLQJIRUWKHUHFHLYHULV

completed, the LED monitor of the receiver

EOLQNVRQFHDQGWKH&+VHUYRVKXWWOHVWKUHH

WLPHVDFURVVWKHQHXWUDOSRVLWLRQ

*A very low power, whose frequency is different from that

of the channel frequency, is used to set the frequency of the

receiver. The reachable distance of the radio is designed to

be within several feet. Therefore, put the transmitter and the

receiver as close as possible when setting the frequency of

the receiver.

,IWKHUHFHLYHUFDQQRWORDGWKHQHZGDWD

GXHWRHQYLURQPHQWDOUHDVRQVFRQQHFWWKH

transmitter and the receiver directly by the

'6&FDEOH$QGGRWKHSURFHGXUHDQG

*LED monitor will blink on and off if the receiver's ID code

is wrong. Then move back to the Receiver ID Set screen and

restart the receiver's ID setting from the beginning.

3XVKWKHEXWWRQ(QGZKHQWKHIUHTXHQF\

VHWWLQJLVFRPSOHWHG<RXZLOOEHDEOHWRXVH

WKHQHZIUHTXHQF\DIWHU\RXSXVKWKHEXWWRQ

<HV

In case of using PCM1024, PPM receivers

*Make sure that PCM1024 or PPM is set as a modulation

scheme. Then change the frequency by the following

instruction.