SYSTEM MENU The System Menu sets up functions of the transmitter: This does not set up any model data. ● Select [SYSTEM] at the home screen and call the system menu shown below by touching the RTN button. ● Scrolling the touch sensor to select the function you want to set and call the setup screen by touching the RTN button. ● Select the function name and return to the System menu by touching the RTN button or pushing the Home/Exit button.
DISPLAY LCD contrast adjustment and automatic key lock The following LCD screen adjustments and auto power off setting are possible: ● Backlighting brightness adjustment ● Backlighting off timer adjustment ● Automatic key lock setup ● Select [DISPLAY] at the system menu and call the setup screen shown below by touching the RTN button. ● Select the function name and return to the System menu by touching the RTN button or pushing the Home/Exit button. LCD contrast adjustment 1.
SYSTEM TIMER Resets the accumulated timer. This function resets the system timer displayed on the home screen. ● T18SZ has two type system timers. TOTAL timer: Displays the total accumulated time on the transmitter from the last time the timer was reset. MODEL timer: Displays the total accumulated time on each model from the last time the timer was reset. ● System timer displayed on the home screen can be selected.
USER NAME User name registration This function registers the T18SZ user name. *A name of up to 12 characters can be entered as the user name. (Space is also counted as 1 character.) ● Select [USER NAME] at the system menu and call the setup screen shown below by touching the RTN button. Current user name ● Select the function name and return to the System menu by touching the RTN button or pushing the Home/Exit button. Cursor (blink) Input box User name registration 1.
SOUND Turns off the buzzer. 3 independent sound volumes: "WARNING", "VOICE" and others, are available. "LOW BATTERY" adjusts low battery alarm voltage to match a battery. ● Select [SOUND] at the system menu and access the setup screen shown below by touching the RTN button. Scrolling ● Moving cursor ● Adjusting value ● Select the function name and return to the System menu by touching the RTN button or pushing the Home/Exit button. ● LOW BATTERY : 6.8V~7.
H/W SETTING Hardware reverse and stick mode, stick calibration, switch position H/W reverse This function reverses the operation signal of the sticks, switches, trimmer levers, and knobs. Note: This setting reverses the actual operation signal, but does not change the display of the indicators on the display. Use the Normal mode as long as there is no special reason to use the Reverse mode. Stick mode This function changes the stick mode of transmitter.
Stick calibration method *J3 and J4 correction is described below. J1 and J2 corrections are performed using the same procedure. Operation switch setting method 1.Select [SWITCH] and call the setup screen shown below by touching the RTN button. 1.Select [CALIBRATION] and access the setup screen shown below by touching the RTN button. 2.Move the cursor to the J3-J4 button and touch the RTN button. 2.
INFORMATION Displays the program version, SD card information, and product ID. The T18SZ system program version information, SD card information (maximum and vacant number of model data), and product ID are displayed on the Information screen. *When the SD card is not inserted, the SD card information is not displayed. The language displayed in home, menu, and setup screen is selectable. Moreover, the unit of a telemetry display can also be changed.
RANGE CHECK Before a flight ground range check. The 'range check mode' reduces the transmission range of the radio waves to allow for a ground range check. WARNING Do not fly in the range check mode. ■ Since the range of the radio waves is short, if the model is too far from the transmitter, control will be lost and the model will crash. *The range check mode, when activated, will continue for90 seconds unless the user exits this mode early.
S.BUS Servo S.BUS/S.BUS2 servo setting An S.BUS/S.BUS2 servo can memorize the channel and various settings itself. Servo setting can be performed on the T18SZ screen by wiring the servo as shown in the figure. T18SZ ●Servo ID number Individual ID numbers are memorized for your S.BUS servos in your T18SZ. When a servo is used (as shown at the right), the servo ID number is automatically read by the transmitter. If you use multiple S.
S.BUS Servo Description of function of each parameter *There are a function which can be used according to the kind of servo, and an impossible function. • ID Displays the ID of the servo whose parameters are to be read. It cannot be changed. • Channel Channel of the S.BUS system assigned to the servo. Always assign a channel before use. • Reverse The direction in which the servo rotates can be changed.
• Boost ON/OFF OFF : It is the boost ON at the time of low-speed operation.(In the case of usual) ON : It is always the boost ON.(When quick operation is hope) • Damper The characteristic when the servo is stopped can be set. When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value is larger than the standard value, the brake is applied before the stop position. Especially, when a large load is applied, overshoot, etc.
MODEL BASIC SETTING PROCEDURE Airplane/glider basic setting procedure 1. Model addition and call 3. Fuselage linkage Initial setting assigns 1 model to the T18SZ transmitter. The Model Select function of the Linkage Menu is used to add models and to select models which are already set. Connect the ailerons, elevators, throttle, rudder, etc. in accordance with the model's instruction manual. For a description of the connection method, see the Receiver and Servos Connection.
throttle cut function operates the throttle stick in the 1/3 or less (slow side) position. 5. Idle down setting The idling speed can be lowered with one touch by a switch without changing the throttle trim position. Perform this setting with the Idle Down function of the Linkage Menu. After activating the Idle Down function and selecting the switch, adjust the idle down speed. For safety, the idle down function acts only when the throttle stick is slow side. chosen.
Helicopter basic setting procedure This section outlines examples of use of the helicopter functions of the T18SZ. Adjust the actual values, etc. to match the fuselage used. 1. Model addition and call Default setting assigns 1 model to the T18SZ. To add new models or to call a model already set, use the Model Select function of the Linkage Menu. *The Model Type function automatically selects the appropriate output channels, control functions, and mixing functions for the chosen model type.
4. Fuselage linkage 5. Throttle/Pitch curve setting Connect the throttle rudder, aileron, elevator, pitch, and other servos in accordance with the kit instruction manual. For a description of the connection method, see "Receiver and Servos Connection". This function adjusts the throttle or pitch operation curve in relation to the movement of the throttle stick for each condition. Note: The channel assignment of the T18SZ is different from that of our existing systems.
6. AFR (D/R) do not use Pitch to RUD mixing. AFR (D/R) function is used to adjust the throw and operation curve of aileron, elevator and rudder for each condition. Call the Pitch to RUD mixing function from the Model Menu, and set the curve for each condition. (At initial setting, this function is in the "INH" state. To use it, set it to the "ON" state.
*With throttle stick at idle, adjust the cut position until the engine consistently shuts off, but throttle linkage is not binding. 11. Swash Mix corrects aileron, elevator and pitch interaction The swash mix function is used to correct the swash plate in the aileron (Left/Right Cyclic) and elevator (Forward/Aft Cyclic) direction corresponding to each operation of each condition. 12.
57
Servo connection by model type The T18SZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for each model type is shown below. Connect the receiver and servos to match the type used. *The set channels can be checked at the Function screen of the Linkage Menu. The channel assignments can also be changed.
●Ailevator 1AIL Airplane 2AIL Glider Airplane EP 2AIL+1FLAP Glider Airplane EP 2AIL+2FLAP Glider Glider Airplane EP The output CH of each system RX CH EP Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator 3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 4 Rudder Rudder Rudder Rudder Ru
●Tailless wing Airplane 2AIL+1FLAP Glider Airplane EP 2AIL+2FLAP Glider Airplane EP The output CH of each system 2AIL RX CH Glider EP Aileron Aileron Aileron Aileron Aileron Aileron Aileron AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 Aileron AUX4 3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Gear AUX6 AUX6 Gear AUX6 AUX6 Aileron2 Aileron2 Aileron2 6 Aileron2 Aileron2 Ailero
●Tailless wing Winglet 2Rudder Airplane 2AIL+1FLAP Glider Airplane EP 2AIL+2FLAP Glider Airplane EP The output CH of each system 2AIL RX CH Glider EP Aileron Aileron Aileron Aileron Aileron Aileron Aileron RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 Aileron RUD2 3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Gear AUX6 AUX6 Gear AUX6 AUX6 Aileron2 Aileron2 Aileron2 6 Aileron2
Helicopter H-4/H-4X Swash All Other 1 Aileron Aileron 2 Elevator Elevator 3 Throttle Throttle 4 Rudder Rudder 5 Gyro Gyro 6 Pitch Pitch 7 Governor Governor 8 Elevator2 Governor2 9 GYRO2 GYRO2 10 GYRO3 GYRO3 11 Governor2 Needle 12 Needle AUX5 13 AUX4 14 AUX3 15 AUX2 16 AUX1 DG1 FASST MULT CH The output FASSTest 18CH CH of each S-FHSS FASST 7CH system ●FASSTest 18CH / FASST MULTI / FASST 7CH / S-FHSS SW DG2 CH H-4/H-4X Swash All Other 1 Aileron Ailero
FUNCTIONS OF LINKAGE MENU The Linkage Menu is made up of functions which perform model addition, model type selection, frequency setting, end point setting, and other model basic settings. The functions which can be selected depend on the model type. A typical menu screen is shown below. ● Select [LINKAGE] at the home screen and call the linkage menu shown below by touching the RTN button. ● Use the touch sensor to select the function you want to set and call the setup screen by touching the RTN button.
SERVO MONITOR Servo Test & Graph Display / Displays servo positions. This is used for testing servo movement. “Moving Test” (repetition mode) and “Neutral Test” (fixed position mode) are available. The “Neutral Test” is good for finding the neutral position of a servo horn. In order to prevent any potential difficulties, the servo test function will be inoperable, or inaccessible, under certain conditions.
MODEL SELECT The Model Selection function performs model addition, call, deletion, copy, and model name setting. This function is used to load the settings of the desired model into the T18SZ’s memory. The settings may be selected from either the transmitter’s built-in memory or a SD card (32MB2GB). Remember that up to 30 model memories are available in the transmitter. The name of the model stored in the transmitter and the SD card may be changed.
Model deletion *The model stored in the transmitter memory or a SD card can be deleted. *The current model can not be deleted. 1. Use the touch sensor to move the cursor to the save destination display ("INTERNAL" or "MEM. CARD") and touch the RTN button to switch to the data input mode. Select the save destination by turning the touch sensor to the left or right and touch the RTN button. [INTERNAL]: Transmitter memory [MEM. CARD]: SD card 2.
MODEL TYPE This function selects the model type from among airplane, helicopter, and glider. Seven types of main wings and three types of tail wings are available for airplanes. Eight swash types are available for helicopters. Seven types of main wings and three types of tail wings are available for gliders. Functions and mixing functions necessary for each model type are set in advance at the factory.
●Model type selection Model type Select the model type from among airplane, helicopter, and glider. (Airplane, glider) (Helicopter) ●Wing type selection ●Swash type selection Helicopter swash type ●Wing type selection (Normal) Select from among H-1, H-2, H-4, HR3, HN3, H-3, HE3, and H4X. ●Wing type selection (Tailless wing) Wing type (Normal) Select from among : 1 aileron, 2 ailerons, 2 ailerons + 1 flap, 2 ailerons + 2 flaps, 2 ailerons + 4flaps, 4 ailerons + 2 flaps, 4 ailerons + 4 flaps.
Model type selection (Airplane, Glider) ●Wing type (Normal) ●Wing type (Tailless wing) ●Rudder type ●Tail type Model type selection (Helicopter) ●Swash type 69
SYSTEM TYPE System mode setting, Receiver link System Type selection The T18SZ is for 2.4GHz only. The system can be changed from among 5 choices: FASSTest 18CH, FASSTest 12CH, FASST MULTI, FASST 7CH, T-FHSS, S-FHSS. It is FASSTest18CH and FASSTest12CH which can be chosen by R7008SB set. The method of selection is to the next page. *If you change the System Type, other model data is not reset.
Telemetry function (FASSTest /T-FHSS mode only) To use the telemetry function, set “Telemetry” to “ACT”. DL Interval (FASSTest/T-FHSS mode only) When a telemetry function is enabled, the receiving interval (down-link interval) of sensor data can be changed. If a DL interval is increased, the response of the sensor data display becomes slower, but stick response will improve. In DUAL, a primary receiver is link previously. Next, a secondary receiver is link. 3.
The example for choosing System Type -Response speed has priority over number of channels -Want to use a previously used receiver as is -Want to use a miniature receiver for indoor planes -Want to use a large number of telemetry functions -Telemetry requires only the current receiver battery FASST 7CH -Want to use more channels -Want to use a large number of telemetry functions FASST MULTI FASSTest 12CH FASSTest 18CH FMR-01 R7008SB R7003SB R7018SB -Want to use an T-FHSS system receiver FMR-01 R70
FUNCTION Channel assignment of each function can be changed. When you select model and wing (swash) types, you will find that the optimized combinations of servo output channels and functions have been already preset. If you would like, you can freely change combinations of servo output channels, functions (aileron, elevator, etc), and control (sticks, switches, and trim levers). channels and two digital channels. For FASSTest 18CH mode, you can set 10 linear channels and two digital channels.
Trim setting Use the touch sensor to move the cursor to the "TRIM" item of the channel you want to change and touch the RTN button. *The trim setup screen is displayed. The following items can be set at the trim setup screen: *The setting can be changed for each condition. After the set mode is changed from group mode [G] to single mode [S] at the control selection screen, only that condition setting is changed by control change; setting of other conditions remains the same.
SUB-TRIM Setting of neutral position of each servo. The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and touchrods are hooked up. When you begin to set up a model, be sure that the digital trims are set to their center position. ● Select [SUB-TRIM] at the linkage menu and call the setup screen shown below by touching the RTN button.
SERVO-REVERSE Use to reverse the throw direction. Servo Reverse changes the direction of an individual servo’s response to a control stick movement. For CCPM helicopters, be sure to read the section on Swash AFR before reversing any servos. With CCPM helicopters, always complete your servo reversing prior to any other programming.
FAIL SAFE Sets the servos operating position when transmitter signals can no longer be received or when the receiver battery voltage drops. The Failsafe function may be used to set up positions that the servos move to in the case of radio interference. You may set either of two positions for each channel: Hold, where the servo maintains its last commanded position, or Failsafe, where each servo moves to a predetermined position. You may choose either mode for each channel.
END POINT Sets the travel, limit point, and speed of each servo. The End Point function adjusts the left and right servo throws, generates differential throws, and will correct improper linkage settings. The travel rate can be varied from 30% to 140% in each direction on channels 1 to 12. Also, the limit point where servo throw stops may be varied from 0% to 155%. NOTE: The servo speed setting is used to set the servo delay for each channel, from channel l to channel 12.
THROTTLE CUT Stops the engine safely and easily.(airplane and helicopter only) Throttle cut provides an easy way to stop the engine, by flipping a switch with the throttle stick at idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch’s location and direction must be chosen, as it defaults to NULL. ● Select [THROTTLE CUT] at the linkage menu and call the setup screen shown below by touching the RTN button.
IDLE DOWN Lowers the engine idling speed.(airplane and helicopter only) The Idle Down function lowers the engines idle by flipping a switch with the throttle stick at idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch’s location and direction must be chosen, as it defaults to NULL. ● Select [IDLE DOWN] at the linkage menu and call the setup screen shown below by touching the RTN button.
SWASH RING Limits the swash plate travel to within a fixed range. (Helicopter only) This function limits the swash travel to within a fixed range to prevent damaging of the swash linkage by simultaneous operation of the ailerons and elevators. It is effective in 3D aerobatics which use a large travel. ● Select [SWASH RING] at the linkage menu and call the setup screen shown below by touching the RTN button.
SWASH Swash operation linkage correction function.(helicopter only, except swash type H-1) Neutral Point Mixing Rate At your linkages, if the servo horn deviates from a perpendicular position at neutral, the linkage compensation functions in this menu may not compensate effectively. To correct this use the neutral point function. This will move the neutral point of the servos to the actual perpendicular position.
Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. Mixing applied in other swash modes is different, but the setting procedure is the same. *Set the throttle stick to the preset neutral point. Adjust the length of the linkage rod so that the swash plate is horizontal at this position. *The sub trim function can be used to make small adjustments. *Adjust so that the pitch curve is a straight line and pitch operation is maximum.
TIMER Timer setting The Timer function may be set for any desired time, i.e. engine run time, specified times for competitions, etc. Two independent timers are provided for your use. The timers are stored independently with each model, meaning that when you switch between model setups, the timer associated with the new model is brought up automatically. The timers may be set to start and stop from the motion of any switch or stick. You may set the ON and OFF directions freely.
Alarm mode *A mode which sounds an alarm every minute during the remaining time up to the timer alarm time. 1. Change the setting by pressing ↑ or ↓ button. [ ↑ ]: An alarm sounds every minute of the elapsed time from timer start. (Conventional mode) [ ↓ ]: An alarm sounds every minute of the remaining time up to the alarm time. HOUR mode *An HOUR mode counts up to 99 hours 50 minutes to the timer modes. ● This mode is convenient when used at engine maintenance period and other long term measurements.
T1-T6 SETTING Digital trim settings This function adjusts the digital trim's control step amount and operation mode (T1~T6.) When the flight conditions are set, the trim operation can be coupled with among all the conditions which combination mode is selected. ● Select [T1-T6 SETTING] at the linkage menu and call the setup screen shown below by touching the RTN button. ● Select the function name and return to the Linkage menu by touching the RTN button or pushing the Home/Exit button.
MULTIPROP CH is extended by MPDX-1 of an option The system has compatible with the Futaba MPDX-1 multiprop decoder. One channel can be expanded to 8 channels by using the MPDX1 multiprop decoder. Up to two MPDX-1 can be used. *The trim step amount and trim rate are not reset. ● Select [MULTPROP] at the linkage menu and call the setup screen shown below by touching the RTN button.
FUNCTION NAME Function name can be changed The name of the spare functions (AUXILIARY1-8) can be changed for the full name (10 characters) or for the abbreviated name (4 characters). ● Select [FUNCTION NAME] at the linkage menu and call the setup screen shown below by touching the RTN button. ● Select the function name and return to the Linkage menu by touching the RTN button or pushing the Home/Exit button. Scrolling ● Moving cursor ● To next page Function name change method 1.
TELEMETRY Displaying data from the receiver This screen displays your choice of data from the receiver. Also warnings can be activated regarding other data from your aircraft. For example, if the receiver voltage drops, the user can be warned by an alarm (and vibration). *It cannot be used in FASST mode and S-FHSS mode. *Only receiver voltage and EXT voltage can be used in FASSTest12CH mode. *The FASSTest18CH mode can use all the telemetry functions.
TELEMETRY : RECEIVER [BATTERY] In this screen, the battery voltage of a receiver is displayed. If it becomes higher or lower than the setting an alarm and/or vibration will alert you. Displaying data from the receiver battery voltage *It cannot be used in FASST mode and S-FHSS mode. *Only receiver voltage and EXT voltage can be used in FASSTest12CH mode. *The FASSTest18CH mode can use all the telemetry functions. ● Receiver battery voltage ● Select [Rx-BATT.
TELEMETRY : RECEIVER [EXT BATT.] The EXT-VOLT screen will display the data from the EXT-battery output from the R7008SB receiver. In order to use this function, it is necessary to connect external voltage connector of the R7008SB receiver to a CA-RVIN-700 (FUTM5551) or SBS-01V to the battery you desire to measure the voltage of the EXT-battery. Displaying data from the EXT battery voltage port *CA-RVIN-700 must be installed in the aircraft.
TELEMETRY : TEMPERATURE Displaying data from the temperature *A temperature sensor must be installed in the aircraft. *It cannot be used in FASST mode and S-FHSS mode. Temperature is a screen which displays/sets *Only receiver voltage and EXT voltage can be used in up the temperature information from an optional FASSTest12CH mode. temperature sensor. *The FASSTest18CH mode can use all the telemetry functions. The temperature of the model (engine, motor, battery, etc.) which is flying can be displayed.
TELEMETRY : RPM SENSOR RPM sensor is a screen which displays / sets up the rotation information from an optional RPM sensor. The rotation of the model (engine, motor, etc.) which is flying can be shown. If it becomes higher or lower than the setting an ● Select [RPM sensor] in the TELEMETRY screen and access the setup screen shown below by touching the RTN button. Displaying data from the RPM *A RPM sensor must be installed in the aircraft. alarm and/or vibration will alert you.
TELEMETRY : ALTITUDE Displaying data from the altitude *An altitude sensor or GPS sensor must be installed in the aircraft. ALTITUDE is a screen which displays / sets up the altitude information from an optional altitude sensor or GPS sensor. The altitude of the model which is flying can be known. If it becomes higher (low) than preset altitude, you can be told by alarm. To show warning by vibration can also be chosen.
data from the TELEMETRY : ALTITUDE [VARIOMETER] Displaying variometer *An altitude sensor or GPS sensor must be installed in the aircraft. for ascent and descent. Additionally, depending VARIO is a screen which displays / sets up the upon the rate of climb or descent, the tones vary to variometer information from an optional altitude indicate whether or not the airplane is climbing or sensor or GPS sensor. descending at a rapid rate.
TELEMETRY : VOLTAGE [BATTERY] In this screen, the battery voltage is displayed. In order to use this function, it is necessary to connect External voltage connector of R7008SB ⇔ SBS-01V ⇔ Battery SBS-01V measures two batteries. The power battery connected to two lines is displayed on EXTVOLT. The battery for receivers connected to 3P lines is displayed here. ●Select [VOLTAGE] in the TELEMETRY screen and access the setup screen shown below by touching the RTN button.
la ying da t a fro m TELEMETRY : VOLTAGE [EXT-VOLT] Disp battery voltage port In this screen, the EXT battery voltage is displayed. In order to use this function, it is necessary to connect External voltage connector of R7008SB ⇔ SBS-01V ⇔ Battery SBS-01V measures two batteries. The power battery connected to two lines is displayed on EXTVOLT. *SBS-01V must be installed in the aircraft. *It cannot be used in FASST mode and S-FHSS mode.
TELEMETRY : GPS [DISTANCE] The Distance screen displays and sets altitude data from an SBS-01G GPS Sensor (sold separately), and allows the distance to the airborne aircraft to be read by the transmitter. When the aircraft flies inside or outside the set distance an alarm and vibration alerts the pilot. ● Select [GPS] in the TELEMETRY screen and access the setup screen shown below by touching the RTN button. Displaying data from the Distance Screen *A GPS sensor must be installed in the aircraft.
First, the set of a reference is required. 1. The model and transmitter to which the GPS sensor was connected are turned on. 2. M o v e t h e c u r s o r t o t h e [ P R E S E T ] o f "REFERENCE" item. 3. Touch the RTN button is pushed for 1 second. (To terminate the input and return to the original state, touch the Home/Exit button.) *Now, the position of the present model was set to 0 m. Setting a "too far" alarm distance 1.
