Model Selsct "MDL SELE" Forty model data (data for 40 R/C cars) can be saved in the T4PM transmitter. This menu selects the model and copies data between models. Display "MDL SELE" screen using the following method: (MENU 2 ) (HOME screen) (MDL SELE screen) MENU-1 MENU-3 MENU-4 Select "MDL SELE" Using the model select function 1 (Model #. selection) Select the model number by moving the (JOG) button up/down or left/right. "01" ~ "40" are displayed. Model #.
Model Name "MDL NAME" This function allows you to assign a ten character name to each model memory and user name. Display "MDL NAME" screen using the following method: (MENU 2 ) (HOME screen) (MDL NAME screen) MENU-1 Model name User name MENU-3 Select "MDL NAME" MENU-4 Setting the model name and user name 1 (Move the cursor to the character you want to change.) Select the model name or user name character you want to set or change by moving the cursor by the (+) or (-) button.
Model Copy "MDL COPY" The contents of the currently selected model data can be copied to another model. Display "MDL COPY" screen using the following method: (MENU 2 ) (HOME screen) (MDL COPY screen) MENU-1 MENU-3 Select "MDL COPY" MENU-4 Using the model copy function 1 (Model #. selection) Select the copy destination model number with the (+) or (-) button. "01" ~ "40" are displayed. Model #. 01~40 The copy destination model # with the (+) or (-) button.
Model Reset "RES" This function resets and initializes the contents of the currently selected model data. However, the adjuster function (ADJUSTER), system setting (SYSTEM), and type of receiver system (RECEIVER) are not initialized. Display "MDL RES" screen using the following method: (MENU 2 ) (HOME screen) (MDL RES screen) MENU-1 MENU-3 MENU-4 Select "MDL RES" Using the model reset function 1 (Model reset execution) Press the (JOG) button for approximately 1 second.
Data Transfer "MDL TRANS" This function copies the model memory data of one T4PM to another T4PM. Connect the communication port of both T4PMs with the optional DSC cable (For updating transmitter with CIU-3). Note: If the T4PM battery voltage drops, the display switches to low battery display. Therefore, use this function when there is ample battery capacity remaining.
2 (Select the setting item ) Select "MODE" by moving the (JOG) button up or down, and select the transfer side and receiving side using the (+) or (-) button. "TRAN": Data transfer side. "RECV": Data receiving side. 3 Mode selection "TRANSFER" "RECEIVE" Setup item selection - Select by (JOG) button up or down operation. Mode change button - Use the (+) and (-) buttons to make adjustments. (Data transfer execution) Select the setting item "EXEC" by moving the (JOG) button up or down on both transmitters.
Fail-safe Function "FAIL SAFE" (All channel) Fail-safe Mode (F/S) This function moves each servo to a preset position when the receiver cannot receive the signals from the transmitter for some reason. -The fail-safe data is transferred from the transmitter to the receiver 10 seconds after the transmitter power was turned on. The data is transferred every 5 seconds after that.
Fail-safe mode selection FAIL SAFE screen (Preparation) - Select the channels "MODE" to be set by moving the (JOG) button up, down, left or right. 1 (Mode selection) Select the mode by (+) or (-) button. (Each channel can be individually set.) 2 When finished with setting, return to the MENU screen by pressing the (END) button. When setting fail-safe, set the servo position by the following method.
Select TRIM Dial Function "TRIM DIAL" Selection of the function to be performed by trims and dial (DT1, DT2, DT3, DT4, DT5, DL1). - The functions that can be assigned to dial and digital trim are listed on the next page. - The dial and digital trim step amount can be adjusted (The relationship between set value and step amount is shown in the table on the next page.). - The operation direction can be reversed (NOR/REV).
DT1 DT2 DT4 DT3 DL1 DT5 Set table functions (DL1, DT1/DT2/DT3/DT4/DT5) Function Abbreviation used on setup screen D/R ATL EXP-ST EXP-FW EXP-BK SPD-TN SPD-RN ABS.PS ABS.DL CYCLE ACC-FW ACC-BK TH-SPD ST-TRM TH-TRM CH3 CH4 SUBTR1 SUBTR2 SUBTR3 SUBTR4 IDLE ESC-RT TH-OFF PMX-A PMX-B BK3-RT BK4-RT 4WS-RT ESC-MD GYRO ACKMAN OFF 68 Function name, etc Dual rate function ATL function Steering EXP Throttle EXP (Forward side) Throttle EXP (Brake side) Steering speed (Turn side) Steering speed (Return side) A.
Select Switch Function "SWITCH" Selection of the function to be performed by the switches (SW1, SW2). - SW2 alternate operation (operation which switches between ON and OFF each time the switch is pressed) is possible. NOR (Normal) -ON only while pressed, OFF when released. ALT (Alternate) -Switched between ON and OFF each time pressed. - SW1 ON/OFF direction can be reversed (NOR/REV).
SW1 SW2 Set table functions (SW1) Abbreviation used on setup screen Function name, etc NT-BRK Neutral brake function ON/OFF ABS A.B.S function ON/OFF IDLE Idle up function ON/OFF PRGMIX Program mixing function ON/OFF TH-OFF Throttle off (engine cut) function ON/OFF CH3 Channel 3 CH4 Channel 4 GYRO Switching GYRO mode OFF Not used Set table functions (SW2) Abbreviation used on setup screen Function 70 Function name, etc NT-BRK Neutral brake function ON/OFF ABS A.B.
Adjuster "ADJUSTER" Steering wheel and throttle trigger neutral position and servo operating angle correction can be applied. This is used when a mechanical offset has occurred for some reason. *However, when correction is made, the set value of all the setting functions must be rechecked. Display the "ADJUSTER" screen using the following method:.
Throttle adjustment (Preparation) On the ADJUSTER screen, select the setting item "THROTTLE" by moving the (JOG) button up or down, and press the (JOG) button. 1 (Throttle neutral adjustment) In the neutral setup screen (fig-1) state, lightly pull the throttle trigger and then press the (JOG) button in without touching the trigger.
Infomation "INFO" Display version of T4PM program, ID information. Display the "INFO" screen using the following method:.
Software Update Whenever improvements and new functions are available, the software of your T4PM radio transmitter can be updated easily online free of charge. The zip file of the update data will be shown on our website. You can download it and make a copy on your microSD card. Below is the procedure for the software update. Caution: Before you update the software, the battery that is connected to the T4PM should be fully charged. Update method 1 Extract the zip file on your computer.
Other Functions Refer to country distributor WEB for detailed the following function explanation. Function List Function Abbreviation Description Of Function TH A.B.S Pumping brake TH MODE Throttle servo neutral position/ Idle-Up/ Neutral brake/ Engine cut S.BUS SX Futaba S.BUS/S.BUS2 servo parameter setup. MC LINK MC851C, 602C, 402CR, 950CR, 940CR, 960CR, 970CR parameters setting function. STR MIX Uses 2 servos to individually control the left and right steering.
Reference Ratings *Specifications and ratings are subject to change without prior notice. Communication method: One-way operation system Maximum operating range: 100m (Except the MINIT system) (Optimum condition) For safety: F/S, B-F/S, ID Transmitter T4PM-2.4G (T-FHSS SR / T-FHSS/S-FHSS system, wheel type, 4 channels) Transmitting frequency band: 2.4GHz band RF power output: 100mw EIRP Power requirement: (Dry cell battery) Penlight x 3 (4.
Warning Displays Low Battery Alarm When the battery voltage of the transmitter falls below the usable range, an audible alarm will sound and " " will be displayed on the LCD screen. LCD screen: (HOME screen) (MENU 1, 2, 3) (Function screen) Audible alarm: Continuous tone. Warning When a low battery alarm is generated, cease operation immediately and retrieve the model. If the battery goes dead while in operation, you will lose control.
MIX Warning LCD screen: When the power switch is turned on while the idle-up, preset (engine cut) or neutral brake function switch is on, an audible alarm will sound and "MIX WARN" will be displayed on the LCD. When that function switch is turned off, the alarm will stop. Audible alarm: Tone sounds (7 times) and stops (repeated) Power off forgotten warning LCD screen: If the T4PM is not operated for 10 minutes, an audible alarm is sounded and "OPE WARN" is displayed on the screen.
T7PX/T4PM Handle This handle is option part for carrying T4PM. Please read the installation instructions of the handle carefully for mounting method and precautions. Using the screw (3.0x12mm cap screw) Other Reference -DSC cable for data transfer (For updating transmitter with CIU-3) -Inductive Charging System ICS LF-01 (Li-FePO4 battery inductive charger for T7PX / T4PV / T4PM) -Dry Battery Box for Transmitter 3P-SQ (It is a standard item attached to T4PM.
When Using Four Dry Batteries When ribs in the battery case are cut by the following method. Cut rib - Cut out the six ribs inside the battery case referring to the figure. - Insert the dry battery box 4P-SQ from the wir ing side as shown above. Coution When putting the dry battery box in the transmitter, please put it in the case from the side with wiring. Also, when removing, please remove from wiring side.
Warranty & Repair Service (In U.S.A) (Warranty) Read the Warranty card. - When requesting warranty service, send the card or some type of dated proof purchase. Technical updates and additional programming examples can be found at: www.futabausa.com (Information needed for repair) If any difficulties are encountered while setting up or operating your T4PM, please consult the instruction manual first.
RADIO CONTROL
