Jupiter Wall Range Hood

Table Of Contents

Futuro Futuro

www.FuturoFuturo.com

Installation Instructions

JUPITER

wall-mount model

MOUNTING INSTRUCTIONS FOR “JUPITER” HOOD - WALL VERSION

ISTRUZIONI MONTAGGIO CAPPA «JUPITER» - VERSIONE PARETE

Pg: 1/2 • Ver: 1.9 • Lang: IT/EN

ENGLISH

Phase 1:

1.) Identify the desired distance (A) between the hood and the cooking surface (Fig.1) - recommended is 26” to 30”.

2.) Remove the screws (V1) and remove the top (C).

3.) Mark the holes V2 and V4, following the dimensions of the drawing (see Fig. 2).

4.) Using a level, check that the 2 holes V2 are horizontal.

5.) For installation into wood beams / joists: drill the holes and screw in the wall attachment screws, leaving approximately 5 mm spacing

between the bottom of the screw head and the wall.

5a.) For installation into concrete / masonry: drill the holes, install the supplied expansion plugs (8mm diameter), then screw in the wall

attachment screws, leaving approximately 5 mm spacing between the bottom of the screw head and the wall.

6.) Attach the security bracket (E) to the wall, as shown in Fig.1.

Phase 2:

1.) Align the holes on the back of the hood with the screws on the wall. Check that the screws are securely seated.

2.) Attach the hood to the wall and screw in the ﬁxing screws.

3.) Ducted installation: attach the duct to the blower output. (Ductless installation: skip this step.)

4.) Disconnect power supply (circuit breaker), then connect the hood's electrical system.

5.) Put the cover back in place and screw it in with the corresponding screws (V1).

6.) Attach the bottom section of the spacer onto the bracket (E) using the metric screws V3.

(Optional) Glass Panel Installation:

1.) Remove the metal ﬁlter using the corresponding handle (M).

2.) Disconnect the connector (S) of the light ﬁxture cable.

3.) Unscrew the 4 knurled metric screws M4 (V4), then remove the lower ring section (A) from the hood body.

4.) Slightly unscrew the two centering / anti-rotation metric screws (V5) in the bottom ﬂange of the hood body (B).

5.) Center the holes of the glass panel with the metric screws.

6.) Re-attach the lower ring section (A) to the body (B) with the 4 knurled metric screws M4.

7.) Re-connect the halogen light connector (S).

8.) Replace the metal ﬁlter.

Fig. P2

446

105 mm

154 mm

Fig. P4

Fig. 2

Fig. 1

PAGE 1
Installation Instructions Futuro Futuro JUPITER www.FuturoFuturo.com wall-mount model MOUNTING INSTRUCTIONS FOR “JUPITER” HOOD - WALL VERSION ISTRUZIONI MONTAGGIO CAPPA «JUPITER» - VERSIONE PARETE ENGLISH : Phase 1: 1.) Identify the desired distance (A) between the hood and the cooking surface (Fig.1) - recommended is 26” to 30”. 2.) Remove the screws (V1) and remove the top (C). 3.) Mark the holes V2 and V4, following the dimensions of the drawing (see Fig. 2). 4.
PAGE 2
Futuro Futuro Installation Instructions JUPITER www.FuturoFuturo.com wall-mount model MOUNTING INSTRUCTIONS FOR “JUPITER” HOOD - WALL VERSION ISTRUZIONI MONTAGGIO CAPPA «JUPITER» - VERSIONE PARETE Fase 1 1) Individuare l’altezza (H1) desiderata tra cappa e piano cottura (Fig. P1). 2) Rimuovere la schiena (A) togliendo i tappi di copertura (V1) e agendo sulle relative viti di ﬁssaggio interne (V2). 3) Segnare i 4 punti di foratura F1 e F2 seguendo le quote indicate in Fig. P1 e Fig.