650 mm (25,6”) Fig. 1 Fig. 2 Fig.
Fig. 3 Fig.
A FASTENING HOLES B HOB Fig. 7 STIRRUP A TOP SECTION CENTER SECTION HOOD UNIT Fig.
GB A INSTRUCTIONS BOOKLET WARNINGS This instruction booklet must be kept together with the appliance for future reference. If the appliance is sold or consigned to other parties, check that the booklet is supplied with it, to ensure that the new user has the correct information on the operation of the range hood and is aware of the warnings. These warnings have been provided for the your safety and the safety of others. As a result, please read them carefully before installing and operating the appliance.
C INSTALLATION (Section reserved for qualified installers of the range hood) Minimum distance: distance between the pan supports of the cooker and the bottom-most section of the hood. When the hood is positioned above a gas equipment this minimum distance must be at least 65 cm (see picture C1) or even more, if this is specified in the instructions for use of the gas cooker. In the outside exhaust version, the diameter of the fume discharge duct must be no smaller than the range hood connection.
E RANGE HOOD WITH OUTSIDE DISCHARGE (exhaust) In this version, the fumes and steam from the kitchen are conveyed outside through an exhaust duct. The exhaust conveyor that protrudes from the upper part of the range hood must be connected to a duct that carries the fumes and steam outside. In this version, the charcoal filters, if fitted, should be removed; to do this, see the instructions in point F.
2. FIVE BUTTON CONTROL PANEL LIGHT- button Pressed: the light is on Released: the light is off MOTOR button - 1, 2, 3, OFF 1: starts the motor at minimum speed 2: starts the motor at medium speed 3: starts the motor at maximum speed OFF: stops the motor 3. ELECTRONIC CONTROL PANEL Light pushbutton • ON: light on (the pushbutton is lit); • OFF: light off; Pushbutton Press to reduce motor speed Speed 1, 2 and 3 are indicated by the number of LEDs that light up (excluding the light and the timer LEDs).
Light pushbutton on remote control: light on/off. – and + pushbutton: increase/decrease speed (to start the motor press either the + or the – pushbutton). Timer pushbutton: see instructions below. Timer and ‘filter clogged’ alarm pushbutton • This function allows the automatic turning off of the hood after running for 15 minutes at the speed previously set (the pushbutton shows a flickering light).
I LIGHTING ASSEMBLY AND REPLACEMENT 1. LIGHT BULB To a) b) c) replace the light bulb: Make sure the appliance is disconnected from the mains power supply. Unscrew the support screw A and remove the light cover. Replace the light bulb with the same model as the original (max 25 W, see the markings near the light). A WARNING! Light bulbs with different shapes and power ratings from the original may seriously damage the light compartment. 2.
How to replace the dicroic lamp: a) Check that the equipment is disconnected from the power supply. b) Remove the lamp with the help of a screwdriver (see figure) c) Replace the lamp with a similar one (dichroic, max 20 W, 12 Volt). Lamp Dicroic spot How to replace a square halogen light: a) Check that the equipment is disconnected from the power supply.
them. Wait until they are completely dry before repositioning them. To remove and replace these filters, see the instructions in point H1. This operation should be performed at regular intervals. 2. CHARCOAL FILTERS These trap the odours present in the stream of air that passes through them. The air is purified by passing a number of times through the filters and being recirculated into the kitchen.
- Ensure that all regulations concerning the discharge of exhaust air have been fulfilled before you use the appliance. Before performing any cleaning or maintenance operations, disconnect the appliance by unplugging it or using the main switch.
position, using 2 screws B fixed in the two slots in the top back panel (Fig. 5). - Fit the safety screws C in the bottom back panels (Fig. 5). Step 2 - After having fixed the hood, connect the flexible hose to the fume outlet hole and to the circular pipe fitting of the motor chamber. - Replace the motor at the bottom of the hood and secure it with the rear metric screw (A) (fig. 2).
