Warranty

CAUTION - SAFETY WARNING:
Any oor surface may become slippery when moisture or debris are present. Proper care and cleaning of vinyl
ooring will reduce the likelihood of slips and falls. Always wipe up any oil, chemicals, or other uids that may
drip or leak from vehicle to prevent hazardous, slippery conditions. Always dispose of hazardous materials
properly. Never leave chemicals on product or wash into sewer system.
Leaving chemicals on the product for a long period of time may cause damage. If concrete oor has been
treated with certain sealers prior to mat installation, sealer may break down over time and adhere to back of
mat without causing damage to mat. Some motorcycle kickstands may cut or damage this product.
CLEANING & CARE:
Surface is easily washed with oor soap and water. Product can be easily washed off inside or outside of
garage. Brush or sweep with cool water using a broom or sponge squeegee. Mild soaps and other household
detergents suitable for oors are usually effective. Never leave harsh detergents or chemicals on product. Some
people prefer moving the product outside and hosing it off. Normal household vinyl cleaners may be used to
increase longevity and to remove stubborn debris. Certain automotive vinyl products may cause surface to
become slippery. Use a non-slip vinyl protector such as a clean-and-shine oor cleaner. After cleaning, apply a
coat of oor polish for vinyl oors to add a long-lasting, high-luster nish, even to older garage oor protectors.
This is not a stain-proof product—certain dyes, inks, rubber tires, and chemicals may cause permanent
staining. Some non-permanent stains can be removed with spray-on Brake and Tool Cleaner, found in many
auto parts stores. without damaging the product. However, use of Brake and Tool Cleaner may cause product
discoloration. Never use harsh chemicals such as tar remover or kerosene on this product.
STOP & READ
Begin by sweeping garage oor clean of debris before unrolling the Garage Floor Protector. Wipe up any oil and
chemicals from oor. In most cases, the product is rolled on a PVC or paper core. The product will initially have
curl marks—this is normal.
Product Rolled on Core: The warmer the conditions, the quicker the curl marks will straighten out and lay at.
Using a wide push broom, push air out from center and work your way outward side-to-side and length-to-
length. Repeat if necessary. Place on garage oor when desired and repeat broom out.
Placement On Garage Floor: For best results, start unrolling process at the garage entrance; nishing at the
back of the garage. Using a wide push broom, push any air out from center and work your way outward
side-to-side and length-to-length. It will take some time for most curl marks to lay at. In cool to cold conditions,
it may take 72+ hours before all curls have relaxed. Depending on the temperature, product may expand or
contract somewhat during process. It is OK to park your car on the Floor Protector during this time.
Trimming & Seaming: For custom t, allow product to relax in place before trimming around edges and
corners. After product has been allowed to relax in place, if you choose to hold down edges or seams between
two oor protectors, we recommend using G-Floor Seaming Tape or 3-M® brand 80 Rubber & Vinyl Spray
Adhesive to hold edges in place.
Interior, Exterior, or Commercial Use: If product is used under extreme heat, such as direct sunlight, the
product may expand or contract a small amount after laying at. For custom t, allow product to relax in place
before trimming around edges and corners. In exterior and commercial applications, we recommend securing
our materials to the oor using a pressure sensitive vinyl adhesive (PSA) or BLT’s G-Floor Sheet Adhesive PSA.
When installing a vinyl product with adhesive, it must be an acrylic-based product. SBR adhesives (rubber-
based) will cause the vinyl ooring to contract. Acrylic-based products are the only adhesives BLT recommends.
The longer it sets, the better it will look
© Better Life Technology, LLC | GF0717WA002
For questions please contact:
913.894.0403 • 877.810.6444
[e-mail]