Operation Guide
Table Of Contents
- Before Getting Started...
- Time Adjustment
- Using Mobile Link with a Mobile Phone
- Getting Ready
- Auto Time Adjustment
- Mode Customization
- Customizing the Timekeeping Mode Screen
- Viewing Step Count Data
- Recording Your Current Location (Location Memory)
- Checking the Distance and Bearing to a Location Memory Point (Location Indicator)
- Auto Altitude Calibration
- Recording Waypoints and Their Altitudes (Mission Log)
- Configuring World Time Settings
- Adjusting Hand Alignment
- Phone Finder
- Configuring Watch Settings
- Changing the Home City Summer Time Setting
- Connection
- Digital Compass
- Altitude Measurement
- Barometric Pressure Measurement
- Checking the Current Barometric Pressure
- Checking Changes in Barometric Pressure Over Time
- Checking the Change in Barometric Pressure between Two Readings
- Barometric Pressure Change Indications
- Calibrating Barometric Pressure Readings (Offset)
- Specifying the Barometric Pressure Unit
- Barometric Pressure Reading Precautions
- Temperature Measurement
- Viewing Altitude Records
- Sunrise and Sunset Times
- Stopwatch
- Timer
- Alarms and Hourly Time Signal
- World Time
- Pedometer
- Hand Alignment Adjustment
- Other Settings
- International Travel
- Other Information
- Troubleshooting
Hand Alignment
Adjustment
Strong magnetism or impact can cause the
time indicated by the analog hands to become
different from the time on the digital display. If
this happens, adjust hand alignment.
Adjusting Hand Alignment
1. Enter the Timekeeping Mode.
l
Navigating Between Modes
2. Hold down (D) for at least five seconds.
Release the button when [00] starts to
flash.
This enables adjustment of second hand
alignment.
Second hand
After 3.5 seconds
After five seconds
3. If the second hand is not at 12 o’clock, use
(A) and (C) to align it.
4. Press (E).
This enables adjustment of the hour and
minute hands.
Minute handHour hand
5. If the hour hand and minute hand are not
at 12 o’clock, use (A) and (C) to align them.
6. Press (D) to exit the setting screen.
Other Settings
This section explains other watch settings you
can configure.
Enabling the Button
Operation Tone
Use the procedure below to enable or disable
the tone that sounds when you press a button.
1. Enter the Timekeeping Mode.
l
Navigating Between Modes
2. Hold down (D) for at least two seconds.
Release the button when the name of the
currently selected Home City appears on
the display.
Home City
3. Press (E) twice.
This causes [KEY♪] or [MUTE] to flash on
the display.
4. Use (A) to select [KEY♪] or [MUTE].
[KEY♪]: Operation tone enabled.
[MUTE]: Operation tone muted.
5. Press (D) twice to exit the setting screen.
Note
●
Note that alarm and timer tones will still
sound even while the operation tone is
muted.
Reflecting Altitude
Differential in Activity
Measurements
You can use the procedure below to specify
whether or not you want to reflect altitude
differential in physical exertion
measurements.
Note
●
Reflecting altitude differential
information in activity measurements
makes it possible to obtain more
accurate activity calculations.
●
G-SHOCK Connected is used to
specify your height and weight, and to
calculate physical exertion.
This information is not displayed on the
watch.
1. Enter the Timekeeping Mode.
l
Navigating Between Modes
2. Hold down (D) for at least two seconds.
Release the button when the name of the
currently selected Home City appears on
the display.
Home City
3. Press (E) six times.
This will display [SLOPE], followed by a
flashing [ON] or [OFF].
4. Use (A) to select [ON] or [OFF].
[ON]: Altitude differential reflected in
physical exertion measurements.
[OFF]: Altitude differential not reflected in
physical exertion measurements.
5. Press (D) twice to exit the setting screen.
Operation Guide 5594
32