MA2207-EA © 2022 CASIO COMPUTER CO., LTD.
Watch Operation Guide 5691 Precautions ● ● Operating Precautions ● Water Resistance ● The information below applies to watches with WATER RESIST or WATER RESISTANT marked on the back cover.
Watch Operation Guide 5691 ● Temperature ● ● Never leave your watch on the dashboard of a car, near a heater, or in any other location that is subject to very high temperatures. Do not leave your watch where it will be exposed to very low temperatures. Temperature extremes can cause your watch to lose or gain time, to stop, or otherwise malfunction. Leaving your watch in an area hotter than +60 °C (140 °F) for long periods can lead to problems with its LCD.
Watch Operation Guide 5691 ● Bacteria and Odor Resistant Band ● The bacteria and odor resistant band protects against odor generated by the formation of bacteria from sweat, which ensures comfort and hygiene. In order to ensure maximum bacteria and odor resistance, keep the band clean. Use an absorbent soft cloth to thoroughly wipe the band clean of dirt, sweat, and moisture. A bacteria and odor resistant band suppresses the formation of organisms and bacteria.
Watch Operation Guide 5691 Battery ● ● The special rechargeable battery used by your watch is not intended to be removed or replaced by you. Use of a rechargeable battery other than the special one specified for your watch can damage your watch. The rechargeable (secondary) battery is charged when the solar panel is exposed to light, so it does not require regular replacement as the primary battery requires.
Watch Operation Guide 5691 Before Getting Started... General Guide ① Watch Face and Display Indicators ② ① ② ③ This section provides an overview of the watch and introduces convenient ways it can be used. Watch Features ● Phone Linking The watch supports connection and communication with a Bluetooth capable phone. ● World Time Display the current time in any one of 38 time zones* around the globe. * Subject to being updated when connected with a phone.
Watch Operation Guide 5691 Navigating Between Modes Each press of (C) cycles between watch modes. ● In any mode, hold down (C) for at least one second to return to the Timekeeping Mode. Timekeeping Mode Cycling Between Timekeeping Mode Digital Display Contents Each press of (A) in the Timekeeping Mode toggles between the display information as shown below. Shifting Hands to Read the Digital Display Hand shift moves the hands out of the way for easy viewing of display information. 1.
Watch Operation Guide 5691 Important! ● Some light sources and environments can cause the watch to become extremely hot during charging, which creates the risk of burn injury and damage to internal watch components. Avoid charging the watch under conditions like the ones described below, where the temperatures may exceed 60 °C (140 °F).
Watch Operation Guide 5691 ● Power Saving Function ● Specifying the Illumination Duration Leaving the watch in a dark location for about one hour between the hours of 10 p.m. and 6 a.m. will cause the display to go blank, and the watch to enter Level 1 power saving. If the watch is left in this condition for six or seven days, the watch will enter Level 2 power saving. You can select either 1.5 seconds or three seconds as the illumination duration. 1. Enter the Timekeeping Mode.
Watch Operation Guide 5691 Linking with a Phone 4. Y Perform the operation shown on the screen of the phone to be paired with. When a connection is established between the watch and phone, [CNCT] will stop flashing. While there is a Bluetooth connection between the watch and phone (Mobile Link), the watch’s current time setting is adjusted automatically. You can also change the watch’s other settings. ● Note ● ● This function is available only while CASIO WATCHES is running on the phone.
Watch Operation Guide 5691 Configuring Reminder Settings Note ● ● ● If the watch does not indicate the correct time even if is able to connect with a phone, adjust the hand positions. l Adjusting Hand Alignment If there is a World Time City specified with CASIO WATCHES, its time will also be adjusted automatically. The watch will connect with the phone and perform auto time adjustment at around 12:30 a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m.
Watch Operation Guide 5691 ● Configuring the Summer Time Setting 1. Y Tap the “CASIO WATCHES” icon. 2. X Hold down (C) for at least three seconds until [CNCT] starts to flash. Release the ● Swapping Your World Time and Home Time 1. Y Tap the “CASIO WATCHES” icon. 2. X Hold down (C) for at least three seconds until [CNCT] starts to flash. Release the button when the mode hand moves to e. button when the mode hand moves to e.
Watch Operation Guide 5691 2. X If the watch is in any mode besides the Timekeeping Mode, hold down (C) for at least one second to enter the Timekeeping Mode. 3. X Hold down (D) for at least three seconds. Release the button when [FIND] starts to flash at low speed. The phone will sound a tone when it establishes a connection with the watch. ● It will take a few seconds before the phone tone sounds. Getting ready to connect with phone Changing the Home City Summer Time Setting 1.
Watch Operation Guide 5691 Connection Note Connecting with a Phone Your watch can connect with a phone that is paired with it. ● If the watch is not paired with the phone you want to connect with, refer to the information below and pair them. l C Pair the watch with a phone. ● Connecting with a Phone ● 3. X Press (C) twice. This causes the seconds to flash. The connection will be terminated if you do not perform any operation on the watch or phone for a fixed amount of time.
Watch Operation Guide 5691 Time Adjustment Using Watch Operations to Adjust the Time Setting Your watch can connect with a phone to obtain information that it uses to adjust its date and time setting. If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.
Watch Operation Guide 5691 3. Keep pressing (C) until the setting you want to change is flashing. ● 4. Configure the date and time settings. ● Each press of (C) moves the flashing to the next setting in the sequence shown below. ● Home City Summer time Seconds Hours Year For all the other settings, use (B) and (D) to change the flashing setting. Holding down (B) or (D) scrolls through settings at high speed.
Watch Operation Guide 5691 Using the Watch in a Medical Facility or Aircraft Whenever you are in a hospital, on an aircraft, or in any other location where connection with a phone may cause problems, you can perform the procedure below to disable auto time adjustment. To re-enable auto time adjustment, perform the same operation again. World Time World Time lets you look up the current time in any one of 38 cities around the globe, and UTC (Coordinated Universal Time). ● l Navigating Between Modes 2.
Watch Operation Guide 5691 Alarm Note ● ● ● While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation. While [UTC] is selected as the city, you will not be able to change or check the summer time setting. If you select a World Time City with CASIO WATCHES and then change to a different city with a watch operation, the CASIO WATCHES city information is deleted from the watch.
Watch Operation Guide 5691 ● To stop the alarm Pressing any button while the beeper is sounding stops it. Note ● Note ● ● A beeper sounds for 10 seconds when an alarm time is reached. ● The watch will automatically return from the Alarm Mode to the Timekeeping Mode if you do not perform any operation for about two or three minutes. Indicators are displayed while any of the alarms or the hourly time signal is turned on.
Watch Operation Guide 5691 ● After Arriving Stopwatch 1. Swap the origin time zone time with the destination time zone time. Before swapping After swapping Destination time The stopwatch measures elapsed time in 1/100-second units for the first hour, and in 1second units after that for up to 24 hours. In addition to normal elapsed time measurements, the stopwatch also lets you take split time and lap time readings. Measuring Elapsed Time 1. Enter the Stopwatch Mode. l Navigating Between Modes 2.
Watch Operation Guide 5691 Measuring a Split Time 1. Enter the Stopwatch Mode. l Navigating Between Modes ● If a stopwatch timing operation is in progress, press (D) to stop it and then press (A) to reset the stopwatch to all zeros before performing the operation in step 2. 2. Press (A) to display [SPL]. Measuring Lap Times 1. Enter the Stopwatch Mode.
Watch Operation Guide 5691 Setting the Countdown Start Time The start time can be set in 1-second units up to 60 minutes. ● Using the Timer 1. Enter the Timer Mode. l Navigating Between Modes If a timer countdown operation is in progress, reset the timer to its current start time before performing this operation. l Using the Timer 2. Hold down (A) for at least two seconds. 2. Use the operations below to perform a timer operation. Release the button when the minutes setting starts to flash.
Watch Operation Guide 5691 Hand Alignment Adjustment This enables adjustment of the hour and minute hands. Strong magnetism or impact can cause the time indicated by the analog hands to become different from the time on the digital display. If this happens, adjust hand alignment. Using CASIO WATCHES to Adjust Hand Alignment If the watch is paired with a phone, you can also use CASIO WATCHES to adjust hand alignment. l Adjusting Hand Alignment Hour hand 1. Enter the Timekeeping Mode.
Watch Operation Guide 5691 Specifying the Day of the Week Language You can select any one of six languages for the day of the week display in the Timekeeping Mode. 1. Enter the Timekeeping Mode. l Navigating Between Modes 2. Hold down (A) for at least two seconds Enabling the Button Operation Tone Use the procedure below to enable or disable the tone that sounds when you press a button. 1. Enter the Timekeeping Mode. l Navigating Between Modes 1. Enter the Timekeeping Mode.
Watch Operation Guide 5691 Resetting Watch Settings This section explains how to return the watch settings below to their initial factory defaults. ● Watch Settings ● Reminder ● Stopwatch ● Timer ● Alarm l Navigating Between Modes 2. Hold down (A) for at least two seconds until the name of the currently selected Home City is displayed. This is the setting mode. The hands automatically shift out of the way for easy viewing of the display and other indicators. Home City 3. Press (C) twice.
Watch Operation Guide 5691 City Name Summer Time Start Summer Time End London 02:00, last 01:00, last Sunday in Sunday in March October Paris 03:00, last 02:00, last Sunday in Sunday in March October Athens 04:00, last 03:00, last Sunday in Sunday in March October Tehran 00:00, 00:00, March 22 September 22 or or 21 21 Sydney, Adelaide 02:00, first Sunday in October 03:00, first Sunday in April 02:00, first Lord Howe Sunday in Island October 02:00, first Sunday in April 02:00, last Wellington
Watch Operation Guide 5691 Copyrights and Registered Copyrights ● ● ● ● ● ● The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by CASIO Computer Co., Ltd. is under license. iPhone and App Store are trademarks of Apple Inc. in the United States and other countries. iOS is a trademark or registered trademark of Cisco Systems, Inc. GALAXY is a registered trademark of Samsung Electronics Co., Ltd.
Watch Operation Guide 5691 Q2 I can’t connect while my phone is in the Airplane Mode. Connection with the watch is not possible while the phone’s Airplane Mode is enabled. After disabling the phone’s Airplane Mode, go to the phone’s Home Screen and tap the “CASIO WATCHES” icon. Next, on the watch, hold down (C) for at least three seconds. Auto Time Adjustment by Bluetooth Connection (Time Adjustment) Phone-Watch Connection Q1 I can’t establish a connection between the phone and watch.
Watch Operation Guide 5691 Alarm and Hourly Time Signal Q1 An alarm does not sound. Is the watch’s battery charged? Keep the watch exposed to light until it recharges sufficiently. l Charging Q3 The hands suddenly start moving at high speed. This is due to the reason (or one of the reasons) below, and does not indicate malfunction. Simply wait until normal hand movement resumes. ● ● Other than the above. The alarm’s settings may not be configured. Configure the alarm settings.