LeviTouch DM-500 SINGLE-ARM MONITOR MOUNT For 15 – 27 in. (38.1 – 68.
Thank you for choosing Gabor. The Gabor Single-Arm Desktop Mount is a sturdy accessory that’s capable of securely supporting monitors from 15–27 inches. The rugged aluminum build and durable gas spring mechanism will hold monitors up to 17.6 pounds. The mount consists of two articulating halves that give you maximum control over swivel, tilt, rotation, and height for precise monitor placement. This desktop mount includes a low-profile clamp that will fit into a space with tight clearance, like a cubicle.
Welcome 3
OVERVIEW Quick release Tilt / swivel adjustment screws VESA mount Tension adjustment screw Cable guides Audio in and out jacks USB 3.
ALSO INCLUDED Supplied Parts & Hardware A M4 × 12 screws B M4 x 30 screws C M6 × 12 hex screws D 4 mm hex key E M8 × 12 hex screws F 5 mm hex key G Spacers H Desk plate M4 M6 M8 Parts A ×4 C ×4 E ×2 G ×4 B ×4 D ×1 F ×1 H ×1 Overview 5
22.8 in. (58 cm) ±90° PRODUCT SPECIFICATIONS 100 75 Monitor display size: 15–27 in. (38.1–68.6 cm) 100 75 Maximum load capacity: 17.6 lb. (8 kg) Maximum desktop thickness: 3.5 in. (9 cm) ±180° VESA standards: 75 × 75, 100 × 100 +90°/-85° Tilt: -90°/+85° Arm pivot: 180° Base rotation: 135° Maximum arm height: 17.7 in. (45 cm) Arm height adjustment: 14 in. (35.6 cm) Connectors: USB 3.0: Standard-A Audio: 1/8 in. (3.5 mm) stereo male (×2) Ports: USB 3.0: Standard-A Audio: 1/8 in. (3.
SAFETY WARNINGS 1 Please read and follow the instructions, and keep this manual in a safe place. 2 Clean this product with only a soft, dry cloth. 3 Keep this product away from children. 4 Make sure everything is secure before proceeding. 5 Make sure that this product is intact and that there are no missing parts. 6 To avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings. 7 Do not exceed the maximum load capacity.
ASSEMBLY INSTRUCTIONS 1. Attach the desk clamp mount to the base with the M6 × 12 hex screws. Use the 4 mm hex key to tighten the screws until secure. 8 Assembly Instructions 2. Align the desk plate with the provided holes, and press it into place over the screws. 3. Attach the clamp to the clamp mount with the M8 × 12 hex screws. Use the 5 mm hex key to tighten the screws until secure.
Important! If installing the desktop mount in a cubicle or other space with limited clearance, slide the clamp mount between your desk and the partition first. Then attach the clamp to the clamp mount from underneath the desk. 4. Tighten the clamp with the locking knob. For the most stability, the clamp should be parallel to the back edge of your desk. Make sure the desktop mount doesn’t wobble or shift and is securely clamped to the desk before proceeding.
ATTACHING THE MONITOR Flush Installation 1. Carefully place your monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 10 Attaching the Monitor 2. Align the holes in the VESA mount with the corresponding mounting holes in your monitor. Important: Make sure the raised edge of the VESA mount is at the top of your monitor. 3.
Recessed Installation If the back of your monitor has a recessed area for the VESA mount, follow these steps: 1. Carefully place your monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 2. Align the spacers with the mounting holes in your monitor. 3. Align the the VESA mount holes with the spacers' mounting holes and monitor mounting holes. 4.
MOUNTING THE MONITOR Once attached to the monitor, slide the VESA mount into the quick release until it locks into place. To remove the monitor, pull the locking tab while lifting the monitor out of the quick release.
ADJUSTING TENSION AND ARTICULATION Important! The arm tension is preset for lighter monitors. To avoid damage, do not continue to loosen the screw if it’s already loose. Arm Tension • To support your monitor’s weight, you can adjust the tension of the mounting arm with the included 5 mm hex key. For heavier monitors, rotate the screw counterclockwise to increase tension. • For lighter monitors, rotate the screw clockwise to reduce tension.
Tilt Monitor Swivel and Tilt Two adjustment screws at the top of the mounting arm regulate the monitor’s (vertical) tilt and (horizontal) swivel action. Position your monitor as desired, and use the 5 mm hex key to tighten the screws (clockwise) to fix the monitor in its position. If you want the monitor to swivel and tilt more freely, use the 5 mm hex key to loosen the screws (counterclockwise). Important! Always hold your monitor with one hand when changing the tension of either screw.
ATTACHING THE CABLES TO YOUR COMPUTER The Single-Arm Desktop Mount offers USB and audio connectivity with your computer, and it gives you a convenient USB 3.0 and audio ports on your desktop. 1. Connect the USB plug to an available USB port on your computer or a USB hub. 2. Connect the pink mini plug to the audio input (mic) jack on your computer. 3. Connect the green mini plug to the output (headphone) jack on your computer.
CABLE ORGANIZATION The desktop mount comes with cable guides to organize the cables from your monitor and prevent clutter. 1. Remove the top cable guide by pressing in on the tabs and pulling the guide out of the arm. 16 Cable Organization 2. Place the monitor cable inside the guide, and snap it back into place. 3. Remove the bottom cable guide by unscrewing the Phillips screw, and gently pull and slide it out of the guide slots. 4. Run the cable inside the guide.
TROUBLESHOOTING The desk is too thick for the clamp. If your desktop is thicker than 3.5 in. (9 cm), follow these steps: 1. Remove the clamp from the clamp mount. 2. Completely remove the clamp screw and attachment. 3. Turn the clamp upside down, and reattach the clamp screw and attachment. The monitor won’t stay in one position. • Make sure your monitor weighs less than 17.6 lb. (8 kg). • Adjust the arm tension by turning the adjustment screw counterclockwise to increase the tension.
CUSTOMER SUPPORT For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2016 Gradus Group LLC. All Rights Reserved.
Customer Support / Warranty 19
WWW.MADEBYGABOR.
