FSM-3760 / FULL SWING WALL MOUNT For 37”- 60” Flat Panel Screens User Manual
Thank you for choosing Gabor. Thank you for choosing Gabor’s full swing flat panel screen wall mount. This heavy-duty wall mount has been engineered to provide your 37”-60” flatscreen monitor with sturdy, long-lasting support that can be relied upon for years of viewing enjoyment.
Welcome 3
Tools Required For Installation Product Specifications • For Mounting 37”-60” Flat Panel Screens On Wooden Studs & Concrete Walls • VESA Mounting Pattern Max. 800x500 • Maximum Load Capacity 132lbs/60kg 1. Power Drill 2.
Wall Mount Mounting Brackets Bubble Level T x1 M4 A x4 M5 D x4 M6 M8 G x4 J x4 Spacer/Washer M x4 Bolt/Washer/ Anchor Hex Key P x6 S x1 B x4 E x4 H x4 K x4 N x4 Q x6 C x4 F x4 I x4 L x4 O x4 R x6 Contents 5
Installation Instructions STEP 1: Installing Dual Mounting Brackets On Rear Of Flatscreen • 6 Begin by aligning both brackets on rear of flatscreen device, while ensuring that device screen is resting on a non-scratch surface. The appropriate bolts and washers should be selected by measuring the height, size and position of holes on rear of flatscreen device, and determining which bolts Installation Instructions and washers fit best.
Hardware Configurations For Display With Flat Back: Install bracket directly to flatscreen device using only bolts and washers provided; align bolt with proper sized hole on washer. (Fig. 1) (Fig. 1) For Display With Curved Backs & Recessed Mountings: Install appropriate sized spacer between bracket and flatscreen device; then fasten securely with bolts and washers. (Fig. 2) (Fig.
STEP 2: Positioning Mount Correctly On Wall • The optimal height to position a flatscreen device is by mounting it at eye-level of viewer. This can be accomplished in one of two ways: Eyelevel Height 8 Installation Instructions • Measure distance from seating area to viewing area to determine proper placement. The ideal position should place the center of the panel (where the diagonals meet) as close as possible to eye-level.
STEP 3: Installing Mounting Bracket Directly On Wall • After confirming height positioning is appropriate by marking wall with a pencil, hold wall mount of mounting bracket firmly against wall and use pencil to mark exact location of drill holes, using included leveler to ensure a proper balance; then remove wall mount and pre-drill holes (see sidebar for specific mounting details regarding sheetrock and concrete walls).
Wall-Type Mounting Details Mounting To Wood Studs Under Sheetrock Wall: Pre-drill holes according to markings on wall with a 5mm drill bit; be sure predrilled holes are at least 30mm deep and at least 12” apart; use appropriate wall anchors to attach wall mount (please verify that included anchors are appropriate). Mounting To Solid Concrete Wall: Pre-drill holes according to markings on wall with a 12.
STEP 4: Hanging Flatscreen Device On Wall Mount • With mounting brackets fastened to rear of flatscreen device, lift entire flatscreen display over silver crossbars of wall mount and - with the flatscreen positioned above the mount - lower flatscreen panel while hooking upper and lower sections of brackets on crossbars; ensure all 4 rubber-tipped arches properly grip their respective crossbars. • Verify that both upper and lower sections are fastened securely before releasing flatscreen.
STEP 5: Positioning Installed Wall Mount • • 12 Upon installation completion, secure power cord for flatscreen device by running it through the plastic loops found on bottom of extending arms; then attach plug to power source. Wall mount can be positioned in 3 easily extendable configurations.
STEP 6: Locking Installed Wall Mount • Flatscreen devices attached to the wall mount can be easily secured with an ordinary padlock (not included). Begin by locating dual round holes on the sides of either mounting bracket. Align silver crescent-shaped locking tab with round holes and slide padlock through holes; verify that crescentshaped tab curves inward and ends directly under mid-section of rubber-tipped arches; close padlock to firmly hold locking tab in place.
Safety Warnings 1 Do not use this product for any flat panel screen device other than what it is intended for; the exact specifications, size parameters and weight limits are found both on the product box and in the instruction manual 2 It is strongly recommended that this product be installed by a qualified professional or installation contractor; Gabor takes no responsibility for any product damage or personal injury resulting from mishandling, incorrect mounting, faulty assembly or improper use of this
Customer Support ONE-YEAR LIMITED WARRANTY: For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
WWW.MADEBYGABOR.
