MD-BD13B / DUAL SEGMENT TWIN-ARM MONITOR mount For 13″–27″ (33-69 cm) LCD desktop computer monitors User Manual
Thank you for choosing Gabor. The Gabor MD-BD13B mounts two 13″–27″ (33–69 cm) LCD computer monitors side by side. It attaches to the edge of your desk via a built-in clamp, freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands.
Welcome 3
(x1) Overview F Mounting Arms G Shaft cap VESA Mount Locking collar Ratchet handle Hex screws Locking knob (behind) ±15° Shaft Clamp Clamp locking knob Overview 4 Cable clips Mounting socket Cable clips Tools Required For Installation • Phillips Screwdriver
A B M4x12 (x8) M5x12 (x8) Also Included Supplied Parts & Hardware A A (8) M4 × 12 screws B (8) M4 × 30 screws C (8) M5 × 12 screws D (8) M5 × 30 screws E 4 mm hex key F (8) Spacers B A A M4x12 (x8) M4 A A A x8 A G Shaft Cap H User Manual M4x30 (x8) M5x30 (x8) C B B B B C x8 M5 M5x12 (x8) B Hex Key C C E x1 (x8) 13X5.5X16.5 C C Spacers C F x8 D Shaft Cap G x1 13X5.5X16.5 M4x12M4x12 (x8) (x8) M5x12M5x12 (x8) (x8) 13X5.5X16.
Product Specifications 360° 360° 360° Monitor display size: 13″–27″ (33–69 cm) Maximum load capacity (per arm): 17.6 lb. (8 kg) VESA standards: 75 × 75, 100 × 100 Tilt: ±15° Swivel: 180° 180° Roll: 360° 180° Installation: Clamp fits desk edges up to 2.4" (6 cm) thick Arm width (extended): 31.5″ (80 cm) Spacer dimensions Length: 16.5 mm Outer diameter: 13 mm Inner diameter: 5.5 mm Height: 22.8″ (58 cm) Weight: 7.5 lb. (3.
Safety Warnings 1 Please read and follow these instructions and keep this manual in a safe place. 2 Clean this product with only a soft, dry cloth. 3 Keep this product away from children. 4 Make sure everything is secure before proceeding. 5 Make sure that this product is intact and that there are no missing parts. 6 To avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings. 7 Do not exceed the maximum load capacity.
Getting Started Decide where you want to place your monitors. When using a dual-monitor setup like this one, position your primary monitor directly in front of you, and your secondary monitor to the side. You shouldn’t need to turn your head to look at your primary monitor. Both monitors should be at eye level, approximately at an arm’s length away. If you have to strain to look at either monitor, readjust its position.
Attaching the Shaft The MD-BD13B easily attaches to most desks up to 2.4" (6 cm) thick. Before attaching the shaft to your desk, make sure you have enough room to fit the entire clamp behind your desk. To attach the shaft to your desk, follow these steps: 1. Loosen the clamp locking knob until you can fit the clamp over the edge of your desk. 2. Fit the clamp over the edge of your desk, and tighten the clamp locking knob until the shaft is securely mounted to your desk.
Attaching Your Monitor to the VESA Mounts: Before attaching your monitor to the VESA mount, you may need to detach your monitor’s built-in stand. For information on how to do this, consult your monitor’s user manual. Depending on how the back of your monitor is configured, you can use one of two methods to install the VESA mount onto your monitor: flush or recessed. If your monitor’s VESA mounting holes are flush with the rest of the monitor, use the Flush Installation instructions on the next page.
Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. Installation Instructions 11 C A~B TV 3. Depending on your monitor’s thread size, insert four of the included M4×12 or M5×12 screws into the VESA mount and use a Phillips-head screwdriver to fasten them until fully tightened. TV 1. Carefully place your monitor facedown on a flat surface.
Recessed Installation Note: Before starting, make sure the VESA mount, mounting arm, and monitor are facing the proper direction. 1. Carefully place your monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 12 Installation Instructions 2. Place four of the included spacers on each of your monitor’s four VESA mounting holes. Tip: Thread each of the screws by hand before fastening them with the screwdriver. 3.
Adjust locating ri and screw up tigh Attaching the Mounting Arm Assembly 1. Loosen the locking collar by rotating the ratchet handle, and then slide the collar onto the shaft. 2. Slide the locking collar to the height at which you want to mount your monitors, and then tighten the ratchet handle to lock the collar in place. 3. Slide the mounting arm assembly (with monitors attached) onto the shaft so it rests on the locking collar, and then fully tighten the locking knob until secure. 4.
Adjusting Tension and Articulation E Max. 8 kg every screen 13" - 27"(33-69cm) Arm Positioning Monitor Tilt, Swivel, and Roll Both arms have two joints apiece, making it easy to adjust your monitors’ horizontal placement. Position the arms as desired and use the included 4 mm hex key to fasten the hex screws until fully tightened. You can adjust the (vertical) tilt and C (horizontal) swivel action of your monitors for optimal viewing comfort.
Customer Support For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
www.madebygabor.