User Manual

MW-C
WALL MOUNT
ADAPTER
For MD-ASL15W and MD-BSL15W Monitor Mounts
User Manual
WWW.MADEBYGABOR.COM
FORWARD YOUR PROOFS
to [e-mail]
FOR APPROVAL
BEFORE FINAL PRODUCTION
DO NOT BEGIN PRODUCTION
WITHOUT PRIOR APPROVAL OF PROOFS
Manual for Wall Mount Adapter
Matte Printing
Folding
Instructions
DO NOT EDIT OR REVISE ARTWORK
We will not approve any artwork which has been altered by the vendor
Thank you for
choosing Gabor.
The Gabor MW-C is a dedicated wall mount for the MD-ASL15W (single display) and
MD-BSL15W (dual display) monitor mounts, replacing the center column and desk clamp to
offer an alternative mounting option. It’s perfect for cramped spaces or desk edges that are
too thick to accommodate a desk clamp. The MW-C frees up valuable desk space and enables
personalized monitor placement for improved safety and comfort over conventional
monitor stands.
Customer Support ONE-YEAR LIMITED WARRANTY
This GABOR product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase
date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to repair or replacement,
at the provider’s discretion, of any product that fails during normal use of this product in its
intended manner and in its intended environment. Inoperability of the product or part(s) shall be
determined by the warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration,
abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may
also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Gabor Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Gabor along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s
own risk and expense.
Attaching Your Monitor to the VESA Mounts
Important! Before mounting the MW-C Wall Mount Adapter, make sure your wall can support the
combined weight of your monitor(s) and the mounting assembly.
Decide where you want to mount your monitor. It should be directly in front of you, at eye level, and
approximately at an arm’s length away. You shouldn’t need to turn your head to look at your monitor.
If you have to strain to look at it, readjust its position. When using a dual-monitor setup, position your
primary monitor directly in front of you, and your secondary monitor to the side.
1. Hold the wall plate against the wall at the desired
mounting location and use the included bubble level
to make sure the plate is level.
2. Use a pencil to mark the mounting holes on the wall,
and then remove the plate from the wall. Use the top
and bottom (larger) holes in the triangular (top)
recess and the middle hole of the bottom recess.
3. Drill holes through the pencil marks and fully insert
the included screw anchors into the holes.
4. Hold the wall plate against the wall and align the
mounting holes with the anchors.
5. Use a Phillips-head power screwdriver to tighten the
included M6×50 wall screws into the anchors until
the plate is securely fastened to the wall.
KOPUL
A Gradus Group Brand
TM
KOPUL
A Gradus Group Brand
TM
For more information or to
arrange service, visit
www.madebygabor.com
or call Customer Service at
212-594-2353.
Product warranty is provided by the
Gradus Group. www.gradusgroup.com
Gabor is a registered trademark of the
Gradus Group. © 2014 Gradus Group LLC.
All Rights Reserved.
GG1
Safety Warnings
Please read and follow these instructions
and keep this manual in a safe place.
Clean this product with only a soft, dry cloth.
Keep this product away from children.
Use only parts provided by the
manufacturer.
Make sure everything is secure before
proceeding.
Do not exceed the maximum load capacity.
Make sure your wall can support the combined
weight of your monitor and the mounting
assembly.
Mounting surfaces should be sturdy and flat.
Do not install this product on a weak, uneven
surface.
1
6
All photos are for illustrative purposes only.
9
2
7
8
3
4
5
M6 M8 Caps Bubble Level
A
x3
C
x3
B
x1
E
x1
D
x1 set
F
x8
A (3) M6 × 50 wall screws
B (1) M6 × 25 screw
C (3) M8 × 40 screw anchors
E Mounting peg cap
F Bubble level
G User manual
D (2) Protective caps (1 set)
Also IncludedWall plate
Product Specifications
Compatibility:
Gabor MD-ASL15W and
MD-BSL15W Monitor
Mounts
Maximum load capacity:
17.6 lb. (8 kg)
Dimensions (H × W × D):
6.6″ × 2.7″ × 2.6″
(16.8 × 6.9 × 6.6 cm)
Weight: 8.8 oz. (249 g)
6. Insert the included protective caps into the plate with
the triangular cap attaching to the middle hole of the
top recess and the other cap fitting into the holes at
each end of the bottom recess.
Attaching Your Gabor Monitor Mount
1. Mount your compatible Gabor monitor mount onto the
MW-C’s mounting peg.
2. Insert your monitor cable(s) into the cable guides on
the underside of the mounting arm(s). If you are using
the MD-BSL15W Dual-Display Mount, you have
completed the mounting instructions and can stop here.
If you are using the MD-ASL15W single-arm mount,
continue below.
3. Insert the included M6×25 screw through
the bottom of the mounting peg, and hold
the screw in place so it protrudes from the
screw hole.
4. Thread the included mounting peg cap onto
the screw as much as possible, and then push
the cap into the socket.
5. Use a short Phillips-head screwdriver to
fasten the screw until fully tightened.