TM-3255, TM-3770 / TILTING TV MOUNT with Post-Installation Adjustment for 32 – 55 in. / 37 – 70 in.
Thank you for choosing Gabor. The Gabor TM-3255 and TM-3770 tilting wall mounts offer rugged and durable support for flatscreen monitors that weigh up to 176 pounds (80 kg). This TV mount’s low 2.1 in. (54 mm) profile assures that your screen will hang practically flush against the wall. Adjustment screws are integrated into the design so you can finetune your screen’s horizontal position even after it’s attached and secured to the mount.
Welcome 3
PRODUCT SPECIFICATIONS • Depth from mounting source: 2.1 in. (54 mm) • Compatible flat-panel screen size: TM-3255: 32 – 55 in. (81.28 – 139.7 cm) TOOLS REQUIRED FOR INSTALLATION • Power drill • Pencil • Phillips screwdriver • • Tape measure 3/16 in. (4.5 mm) drill bit (for Wood installation) • Wall stud finder • 3/8 in. (10 mm) drill bit (for drywall and concrete installation) TM-3770: 37 – 70 in. (94 – 177.
Wall Mount Hex Key Bubble Level Wall Hardware Mount Hardware A ×4 D ×4 F ×4 I ×4 B ×4 E ×4 G ×8 J ×4 H ×4 K ×4 Brackets C ×4 Locking Bar Contents 5
ATTACHING BRACKETS TO THE SCREEN Determine whether screws A, B, or C fit the threaded holes on the back of your screen. Note: The screw should go in easily with hand-turning. If the screw slides into the hole, or force is needed to screw it in, select a different size. 6 Installation Instructions Using spacers Two different sizes of spacers are included with this wall mount.
1. Align the screw holes with the mounting holes on your screen. The brackets should be positioned with the small, round screw holes at the top of the screen. 2. Attach the brackets, using washers (F) and screws.
ATTACH THE WALL PLATE TO THE WALL Wood Stud Installation 1. Use a stud finder to locate the studs in your wall, and mark the locations with a pencil. Note: It’s important to find both edges of the stud, so you can drill a pilot hole in the center of the stud. 8 Installation Instructions 2. Place the wall mount over your pencil marks. Use the included leveler to make sure the wall mount is straight. Mark the appropriate wall mount holes with a pencil. 3. Use a 3/16 in. (4.
5. Check the horizontal orientation by placing the bubble level on the top edge of the wall mount. If the mount isn’t perfectly horizontal, gently tap the side that needs adjustment. 6. Once the wall mount is straight, tighten the screws until the mount secure.
Drywall and Concrete Wall Installation 1. In the area where you want to mount your screen, use the leveler to ensure the wall mount is straight, and mark the appropriate mount holes with a pencil. 2. Use a 3/8 in. (10 mm) drill bit, and drill holes approximately 2.4 in. (60 mm) deep into the wall, and insert the anchors (J) into the holes. 10 Installation Instructions 3.
MOUNTING THE SCREEN TO THE WALL MOUNT 1. Lift the screen up to the wall mount, and hang the screen from the top hooks of the brackets. Important! We recommend that two people perform this step. 2. Use the tilt tensions knobs on both brackets to adjust the tension on the tilting mechanism.
USING THE LOCKING BAR 1. For extra security, align the locking bar with the bottom hooks of the brackets, and slide it in from the right side behind the screen. The corner tab of the locking bar should face out, away from the wall. 12 Installation Instructions 2. Insert a lock into the hole at the end of the locking bar.
POST-INSTALLATION ADJUSTMENT Adjustment screws are located at the top of each bracket. Once your screen is mounted on the wall mount, use the included bubble level to check the horizontal orientation of your screen. If necessary, use the included hex key to turn the adjustment screws until the bubble is between the two level lines.
SAFETY WARNINGS 1 Do not use this product for any flat-panel screen device other than what it is intended for; the exact specifications, size parameters, and weight limits are found both on the product box and in the instruction manual.
CUSTOMER SUPPORT For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2019 Gradus Group LLC. All Rights Reserved.
WWW.MADEBYGABOR.