TM-UL / UNIVERSAL TILTING WALL MOUNT for Large Flat-Panel Displays User Manual / IVERSAL TM -UL / UN T LL MOUN TILTING WA
Thank you for choosing Gabor. The Gabor TM-UL Universal Tilting Wall Mount offers compatibility with a wide range of screen sizes measuring 42 to 90 inches and provides a slim mounting depth of 2.2 inches away from the wall. This durable and discreet support holds large flat-panel displays weighing up to 176 pounds and offers a tilting range of 15° so you can adjust for optimal viewing angles.
Safety Warnings • When installing this product, be sure to refer to the mounting instructions detailed in this manual; failure to abide by the mounting instructions may void the product’s warranty. • Do not mount the device on structures that may be affected by vibrations or noticeable impacts; do not install near a heater, fireplace, or any other source of direct heat energy.
Product Specifications Depth from Mounting Source 2.2 in. (5.6 cm) Tilt angle +5° to -10° Recommended Screen Sizes 42 to 90 in. (106.7 to 228.6 cm) Material Steel VESA Mounting Patterns 200 × 200 mm 300 × 200 mm 300 × 300 mm 400 × 200 mm 400 × 300 mm 400 × 400 mm 600 × 400 mm 800 × 400 mm Wall-plate dimensions 35.25 in. x 8.87 in. (89.5 cm x 22.5 cm) Max Weight Capacity 176 lb. (80 kg) 4 Weight 8 lb. (3.
Overview Required Tools Display Brackets Wall Bracket Drill Phillips screwdriver TM-UL / UNIVERSAL / TILTING WALL MOUNT Adjustable crescent wrench A 4X B 4X C 4X D 4X E 4X F 4X G 8X Hammer M6,M8 Stud finder M5 M5 × 14 mm screws H 8X M6 × 14 mm screws I 6X M6 × 30 mm screws J 6X M8 × 30 mm screws M8 × 50 mm screws Rectangle washers K L M 6X 1X 1X Small spacers Tape measure 3/16 in. (4.5 mm) Wood drill bit 3/8 in.
Display/TV Placement Before installing the Gabor Tilting Wall Mount, you will need to determine the placement of your display and identify surrounding support structures for attachment. The best height for a display is at the viewer’s eye level. You can find this height in one of two ways. 1. Measure the distance from the seating area to the viewing area. The ideal position is when the center of the display (where the diagonals meet) is as close as possible to eye level. OR 2.
Attaching the Display/TV Brackets Selecting the Right VESA Mounting Hardware for Your Display A variety of screws are included to fit VESA standards on the backs of most displays. Select the M5, M6, or M8 screws and washers that best fit your display. Hand-thread the screws to determine the correct diameter. A 4X B 4X C 4X D 4X E 4X F 4X If Your Display Has Recessed Mounting or a Curved Back: Install the spacers between the bracket and your display. You can combine spacers to best fit your display.
Attaching the Wall Bracket to Wooden Studs I 4X K 4X L 1X M 1X Wooden studs run vertically inside the wall, 16 inches apart, behind the drywall or plaster. The wall bracket must be mounted to a wooden stud, or the bracket could fall out and damage your display or cause personal harm. 3. Use a stud finder to locate the edges of the wooden stud, and mark the center. Stud 1. Drywall X 2. 8 Place the wall bracket template up to the marked locations, and tape it to the wall.
Attaching the Wall Bracket to Concrete I 6X J 6X K 6X L 1X M 1X Warning! Make sure the concrete wall is solid and at least 8 inches (20 cm) thick. If the concrete exhibits cracks or other defects, this may result in failure of the concrete anchors and cause serious personal injury or damage your display. 1. 2. Place the wall bracket template up to the marked locations, and tape it to the wall. Use the provided bubble level to make sure the bracket is level before drilling.
Mounting the Display on the Wall Bracket Important! We recommend that two people perform this step. 1. Lift your display up to the wall bracket, and hang the display from the top hooks of the brackets. 2. Use a Phillips screwdriver to tighten the Phillips screws at the bottoms of the display brackets.
Adjusting the Tilt Angle Use the tilt tension knobs on both brackets to adjust the tension for the tilting mechanisms. Tilt the display to the ideal viewing angle from +5° to -10°, and tighten the tilt tension knobs until secure.
Five-Year Limited Warranty This Gabor product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of five (5) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
