Use and Care Manual & Installation Guide
Table Of Contents
- AF 2..
- Table of ContentsUse and care manual and installation instructions
- Use and care manual
- 9 Safety DefinitionsSafety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- WARNING
- General notes
- Fire Safety
- WARNING
- to reduce the risk of a range top grease fire:
- a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
- b) Always turn hood ON when cooking at high heat.
- c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
- d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
- CAUTION
- to reduce the risk of a range top grease fire:
- WARNING
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- Burn Prevention
- Child Safety
- Cleaning Safety
- Safe use
- Proper Installation and Maintenance
- Proposition 65 Warning:
- Causes of Damage
- Protecting the environment
- Operating modes
- Operating the appliance
- Cleaning and maintenance
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- Cleaning agents
- Cleaning the metal grease filter
- Uninstalling metal grease filter
- 2 Open the lock on the metal grease filter and pull the metal grease filter out of the retainer at an angle. When you do this, take hold of the metal grease filter from underneath with your other hand.
- 3 Push and open the push-to-open mechanism again.
- Troubleshooting
- Customer service
- IMPORTANT SAFETY INSTRUCTIONS
- WARNING
- WARNING
- WARNING
- WARNING
- WARNING
- Risk of fire
- WARNING
- Risk of fire
- WARNING
- WARNING
- WARNING
- WARNING
- Note:
- Appliance Handling Safety
- Safety Codes and Standards
- Electric Safety
- Related Equipment Safety
- Proposition 65 Warning:
- Before you beginBefore you begin
- General NotesGeneral Notes
- Preparing the units
- Appliance dimensions and safety clearances
- 2 Remove cabinet base, if installed. Mark the fastening points on the inside of the cabinet and use a bradawl to make indentations where the holes are to be. To help you mark the fastening points, use the mounting piece provided.
- 2 Remove the tabs from the bottom of the mounting pieces. ©
- 3 Remove the tabs from the bottom of the mounting pieces. ª
- Electrical connection
- Installation
- Mounting the appliance
- 3 If required, shorten the filler strip to the required dimension. ©
- 2 Push in the fastening bolt gently with your fingers, and turn it until it comes out of the housing along with the spring.©
- 3 Carefully remove the appliance.
- 4 Fasten the filler strip in place.
- 5 Push in the fastening bolt and turn it 90°.
- 3 Fit the protective caps on the left and right. ª
- 4 Remove the protective caps from the fastening elements.
- Table des matièresNotice d’utilisation et de montage
- Notice d'utilisation
- 9 Définitions de sécuritéDéfinitions de sécurité
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- AVERTISSEMENT
- Instructions générales
- Sécurité-incendie
- AVERTISSEMENT
- pour réduire le risque d'incendie de graisse de cuisinière:
- a) Ne laissez jamais la surface de cuisson sans surveillance à des températures élevées. Les débordements causent de la fumée et les résidus graisseux peuvent s'enflammer.. Faites chauffer les huiles lentement à feu doux ou moyen.
- b) Faites toujours fonctionner la hotte lorsque vous cuisinez à feu vif.
- c) Nettoyez les ventilateurs régulièrement. Ne laissez pas la graisse s'accumuler sur le ventilateur ou sur le filtre.
- d) Utilisez des casseroles de taille appropriée. Utilisez toujours des récipients adaptés à la taille de la surface de cuisson.
- ATTENTION
- pour réduire le risque d'incendie de graisse de cuisinière:
- AVERTISSEMENT
- AVERTISSEMENT
- Risque d'incendie
- AVERTISSEMENT
- Risque d'incendie
- AVERTISSEMENT
- Risque d’incendie
- AVERTISSEMENT
- Risque d'incendie
- AVERTISSEMENT
- Risque d’incendie
- AVERTISSEMENT
- Risque d'incendie
- AVERTISSEMENT
- Prévention des brûlures
- Sécurité des enfants
- Consignes en matière de nettoyage
- Sécurité à l'utilisation
- Installation et entretien corrects
- Avertissement issu de la proposition 65 :
- Causes des dommages
- Protection de l'environnement
- Modes de fonctionnement
- Utilisation de l'appareil
- Nettoyage et entretien
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- Produits de nettoyage
- Nettoyage du filtre à graisse métallique
- Retirer le filtre à graisse métallique
- 2 Déverrouiller le filtre à graisse métallique et le retirer de sa fixation en l'inclinant. Placer l’autre main dessous pour saisir le filtre à graisse métallique.
- 3 Appuyer de nouveau sur le mécanisme d’ouverture par pression et l'ouvrir.
- Anomalies, que faire ?
- Service après-vente
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- AVERTISSEMENT
- AVERTISSEMENT
- AVERTISSEMENT
- AVERTISSEMENT
- AVERTISSEMENT
- Risque d'incendie
- AVERTISSEMENT
- Risque d’incendie
- AVERTISSEMENT
- AVERTISSEMENT
- AVERTISSEMENT
- AVERTISSEMENT
- Remarque :
- Sécurité de manutention des appareils
- Codes et normes de sécurité
- Sécurité électrique
- Équipement de sécurité
- Avertissement issu de la proposition 65 :
- Avant de commencerAvant de commencer
- Instructions GénéralesInstructions Générales
- Préparation du meuble
- Dimensions de l'appareil et distances de sécurité
- 2 Si présent, retirez le fond du meuble. Tracez les points de fixation sur les parois intérieures du meuble et pré-percez-les avec un poinçon. Utilisez l'élément de fixation joint pour tracer les points de fixation.
- 2 Retirez les pattes sous les éléments de fixation. ©
- 3 Retirez les pattes sous les éléments de fixation. ª
- Branchement électrique
- Installation
- Accrochage de l'appareil
- 3 Si nécessaire, raccourcissez la baguette murale à la dimension requise. ©
- 2 Enfoncez légèrement le boulon de fixation avec les doigts et tournez jusqu'à ce qu'il s'enlève du boîtier avec les ressorts.©
- 3 Retirez l'appareil avec précaution.
- 4 Vissez fermement la baguette murale.
- 5 Enfoncez le boulon de fixation et tournez-le à 90°.
- 3 Encliquetez les capuchons à gauche et à droite. ª
- 4 Ôtez les capuchons des fixations.
- ÍndiceInstrucciones de uso y montaje
- Manual de instrucciones
- 9 Definiciones de seguridadDefiniciones de seguridad
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- ADVERTENCIA
- Indicaciones generales
- Seguridad para evitar incendios
- ADVERTENCIA
- para reducir el riesgo de incendio ocasionado por la grasa en la estufa:
- a) Nunca deje las unidades de la superficie sin vigilancia en valores altos. Los derrames por hervor producen humos y salpicaduras grasosas que pueden prenderse fuego. Caliente los aceites despacio a temperaturas bajas o medianas.
- b) Siempre encienda la campana al cocinar a una temperatura alta.
- c) Limpie los ventiladores extractores con frecuencia. No se debe permitir la acumulación de la grasa en el ventilador ni en el filtro.
- d) Use el tamaño de cacerola adecuado. Siempre use utensilios de cocina apropiados para el tamaño del elemento de la superficie.
- ATENCION
- para reducir el riesgo de incendio ocasionado por la grasa en la estufa:
- ADVERTENCIA
- ADVERTENCIA
- Peligro de incendio
- ADVERTENCIA
- Peligro de incendio
- ADVERTENCIA
- Riesgo de incendio
- ADVERTENCIA
- Peligro de incendio
- ADVERTENCIA
- Riesgo de incendio
- ADVERTENCIA
- Peligro de incendio
- ADVERTENCIA
- Prevención de quemaduras
- Seguridad de los niños
- Seguridad en la limpieza
- Seguridad durante su uso
- Instalación y mantenimiento adecuados
- Advertencia en virtud de la Proposición 65:
- Causas para los daños
- Protección del medio ambiente
- Modos de funcionamiento
- Operar el equipo
- Limpieza y mantenimiento
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- Productos de limpieza
- Limpiar los filtros metálicos para grasa
- Desmontar el filtro de metal antigrasa
- 2 Abrir el bloqueo del filtro de metal antigrasa e inclinar el filtro de metal antigrasa para sacarlo de la sujeción.Agarrar por debajo el filtro de metal antigrasa con la otra mano.
- 3 Volver a presionar el mecanismo Push-to-open y abrir.
- ¿Qué hacer en caso de fallas?
- Servicio al Cliente
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- ADVERTENCIA
- ADVERTENCIA
- ADVERTENCIA
- ADVERTENCIA
- ADVERTENCIA
- Peligro de incendio
- ADVERTENCIA
- Riesgo de incendio
- ADVERTENCIA
- ADVERTENCIA
- ADVERTENCIA
- ADVERTENCIA
- Nota:
- Seguridad de manejo del electrodoméstico
- Códigos y normas de seguridad
- Seguridad eléctrica
- Seguridad del equipo relacionado
- Advertencia en virtud de la Proposición 65:
- Antes de empezarAntes de empezar
- Información GeneralInformación General
- Preparación de los muebles
- Dimensiones del aparato y distancias de seguridad
- 2 Retirar el panel inferior del armario si cuenta con él. Trazar los puntos de fijación en los interiores del armario y marcarlos con un buril. Para marcar los puntos de fijación, utilizar la pieza de fijación adjunta.
- 2 Extraer las lengüetas inferiores de las piezas de fijación. ©
- 3 Extraer las lengüetas inferiores de las piezas de fijación. ª
- Conexión eléctrica
- Instalar
- Enganchar el aparato
- 3 En caso necesario, acortar el listón terminal de la pared a la medida requerida. ©
- 2 Presionar levemente y girar el perno de fijación con los dedos hasta que se suelte de la carcasa junto con el resorte.©
- 3 Extraer con cuidado el aparato.
- 4 Atornillar el listón terminal de la pared.
- 5 Presionar el perno de fijación y girarlo 90°.
- 3 Enganchar los tapones protectores a la izquierda y la derecha. ª
- 4 Retirar los tapones protectores de las fijaciones.
9 IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
16
WARNING
When the hood is operated in exhaust-air mode
simultaneously with a different burner which also
makes use of the same chimney (such as gas, oil or
coal-fired heaters, continuous-flow heaters, hot-water
boilers) care must be taken to ensure that there is an
adequate supply of fresh air which will be needed by
the burner for combustion.
Safe operation is possible provided that the under
pressure in the room where the burner is installed
does not exceed 4 Pa (0.04mbar).
This can be achieved if combustion air can flow
through non-lockable openings, e.g. in doors,
windows and via the air-intake/exhaust-air wall box or
by other technical measures, such as reciprocal
interlocking, etc.
WARNING
Avoid carbon monoxide poisoning – Provide adequate
air intake so combustion gases are not drawn back
into the room.
An air-intake/exhaust-air wall box by itself is no
guarantee that the limiting value will not be exceeded.
Note: When assessing the overall requirement, the
combined ventilation system for the entire household
must be taken into consideration. This rule does not
apply to the use of cooking appliances, such as
cooktops and ovens.
CAUTION
For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
Risk of damage from condensation back flow. Install
exhaust vent at a slight downward slope away from the
appliance (1° slope).
Appliance Handling Safety
Unit is heavy and requires at least two people or
proper equipment to move.
Hidden surfaces may have sharp edges. Use caution
when reaching behind or under appliance.
WARNING
Risk of injury
The appliance may fall from the wall if it is not
attached properly. All fastening components must be
fixed firmly and securely in place.
Safety Codes and Standards
This appliance complies with the latest version of one
or more of the following standards:
▯ UL 507- Electric Fans
▯ CAN/CSA C22.2No. 113- Fans and Ventilators
It is the responsibility of the installer to determine if
additional requirements and/or standards apply to
specific installations.
Electric Safety
WARNING
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the
electric current.
This appliance is equipped with a cord having a
grounding wire with a grounding plug. The plug must
be plugged into an outlet that is properly installed and
grounded.
WARNING
Improper grounding can result in a risk of electric
shock. Consult a qualified electrician if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is properly
grounded. Do not use an extension cord. If the power
supply cord is too short, have a qualified electrician
install an outlet near the appliance.