Instructions for Use

en-us Basic Operation
16
Setting the temperature unit
Requirement:The display shows the possible units °C
and °F. The unit °C is preset.
1. Turn the rotary selector to set the required unit.
2. Press to confirm.
Ending initial use
Requirement:The display shows "Initial use complete".
▶ Press ⁠.
a The appliance switches to standby mode.
a The display shows the standby screen.
a The appliance is ready to use.
Cleaning the door pane
Note:To ensure tightness, the door seal is lubricated at
the factory. Residue may remain on the door pane.
▶ Before using for the first time, clean the door pane with
glass cleaner and a window cloth or a microfiber cloth.
Do not use a glass scraper.
Cleaning theaccessories
▶ Before first use, clean the accessories thoroughly using
hot soapy water and a soft cloth.
Heating up the appliance
1. Ensure that there is no leftover packaging in the oven
cavity.
2. Remove any accessories from the oven cavity.
3. To eliminate the new-appliance smell, heat up the
empty appliance with the door closed.
The ideal setting for heating is and 200°C for one
hour.
Basic Operation
7 Basic Operation
Basic Operation
7.1 Activating the appliance
1. To exit standby mode, open the door and turn the func-
tion selector or touch a control panel.
2. Set the required function.
Note:The appliance rinses automatically before each
cooking process if it has not been operated for more than
100hours.
The appliance rinses automatically after every cooking
process.
7.2 Opening the appliance door
1. Press ⁠.
a The appliance opens the appliance door.
2. Use the recessed grip on the side of the oven to open
the appliance door fully.
If the childproof lock is activated, press and hold for a
few seconds until the appliance opens the door.
7.3 Switching on the appliance
1. Use the function selector to set the required type of
heating.
a The display shows the selected type of heating and the
suggested temperature.
2. If required, use the rotary selector to set the desired
temperature.
a The display shows the heating symbol ⁠.
a The bar shows the current pre-heat status.
a Once the appliance reaches the set temperature, a sig-
nal tone sounds and the heating symbol goes out ⁠.
Note:If you select a different type of heating, the tempera-
ture that has been set is retained.
The display only shows the suggested temperature once
the appliance has been switched on.
7.4 Switching off the appliance
▶ Turn the function selector to ⁠.
Depending on the type of heating, you may hear an au-
tomatic rinse cycle running.
7.5 Steam injection
During steam injection, the appliance injects steam into
the oven cavity. This enables you to bake food such as
bread and bread rolls with sufficient moisture. It also gives
yeast-risen baked goods a smooth, shiny crust.
Steam injection only works with the following types of
heating:
¡ Hot air + 30% humidity
¡ Hot air + 0% humidity
¡ Full surface grill + air recirculation
Starting steam injection
▶ Press ⁠.
a After a short time, the appliance injects steam into the
oven cavity.
a Steam is injected for approximately5minutes.
Canceling steam injection
▶ Press ⁠.
7.6 Steam removal
During the steam removal process, the appliance intro-
duces cold water into the oven cavity. The steam con-
denses on the oven cavity wall and the oven cavity cools
down.
If you open the appliance door after steam removal, only a
little steam escapes.
WARNING
Hot water may drip down from the appliance door.
▶ Wait until the water on the appliance door has cooled
down.
Steam removal only works with the following types of
heating and if the temperature in the oven cavity is below
270°C (130°C):
¡ Hot air + 100% humidity
¡ Hot air + 80% humidity
¡ Hot air + 60% humidity