Instructions for Use
Table Of Contents
- Dishwasher
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Preventing material damage
- 3 Environmental protection and energy-saving
- 4 Familiarizing yourself with your appliance
- 5 Dishwasher Cycles
- 6 Options
- 7 Features
- 8 Before using for the first time
- 9 Water softening system
- 10 Rinse aid system
- 11 Detergent
- 12 Dishware
- 13 Basic Operation
- 13.1 Protection against unintentional operation
- 13.2 Opening the appliance door
- 13.3 Switching on the appliance
- 13.4 Setting a cycle
- 13.5 Setting options
- 13.6 Setting the electronic delay time
- 13.7 Starting the wash cycle
- 13.8 Interrupting the wash cycle
- 13.9 Terminating the wash cycle
- 13.10 Displaying wash cycle information
- 13.11 Switching off the appliance
- 14 Basic settings
- 15 Home Connect™
- 16 Cleaning and maintenance
- 17 Troubleshooting
- 18 Transportation, storage and disposal
- 19 Customer service
- 20 Technical specifications
- 21 Statement of Limited Product Warranty
en-us Troubleshooting
28
Issue Cause and troubleshooting
E:6103 lights up. Water is not
draining.
Cover of wastewater pump is loose.
▶
Secure the cover of the Wastewater pump →
Page33
so it clicks into position.
E:6102 lights up. Wastewater pump is blocked.
▶
Clean the wastewater pump.
→
"Clean wastewater pump", Page33
Cover of wastewater pump is loose.
▶
Secure the cover of the Wastewater pump →
Page33
so it clicks into position.
E:9001 lights up. Power voltage is too low.
There is no problem with the appliance.
1. Call an electrician.
2. Have the power voltage and electrical installation checked by an electrician.
A different error code appears in
the display window.
E:0100 to E:9010
There is a technical issue.
1. Press .
2. Pull out the power cord plug of the appliance or switch off the breaker.
3. Wait at least 2minutes.
4. Insert the power cord plug of the appliance in a power outlet or switch on the
breaker.
5. Switch the appliance on.
6. If the problem occurs again:
‒ Press .
‒ Turn off the water faucet.
‒ Pull out the power cord plug.
‒ Contact customer service →
Page34
and give the error code.
Dishware is not dry. No rinse aid used or dosage set too low.
1.
Add Rinse aid →
Page15
.
2. Set the amount of rinse aid to be dispensed.
→
"Setting the amount of rinse aid", Page16
Cycle or cycle option has no drying phase, or drying phase is too short.
▶
Select a wash cycle with drying. →
Page9
Some option buttons decrease the drying result.
Water collects in recesses of dishware or silverware.
▶
Position dishware at an angle where possible.
The combined detergent used has a poor drying performance.
1. Use rinse aid to improve drying performance.
2. Use a different combined detergent with a better drying performance.
Extra Dry not activated to improve drying performance.
▶
Activate Extra Dry →
Page22
.
Dishware removed too early or drying process not yet ended.
1. Wait until the program ends.
2. Only remove dishware 30minutes after the program has ended.
Rinse aid used has a limited drying performance.
▶
Use a name-brand rinse aid.
Eco products may have limited effectiveness.
Silverware is not dry. Silverware not arranged properly in the silverware basket or silverware drawer.
Droplets can form on the contact points of silverware.
1.
Arrange silverware individually where possible. →
Page18
2. Avoid points of contact.