Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
13
Getting Started en-us
Switching on the appliance for the first
time
When you first turn on the dishwasher, you are taken
directly to the settings for switching on the appliance for
the first time. The following text is indicated on the
display window at the top @:
Scroll with < >
Set with + -
Leave with t 3 sec.
The required settings for switching on the appliance for
the first time are listed in the table below.
Change the setting as follows:
1. Keep pressing button > ` until the required setting
is displayed.
2. Make the selection with setting buttons + - X.
3. Press and hold the Info button (8 for 3 seconds.
The selected setting has now been stored.
--------
Settings
The dishwasher has been preset with certain settings
for your convenience. You can change these factory
setting.
Change the setting as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button ( 8 for 3 seconds until the
following text is indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with t 3 sec.
4. Keep pressing button > ` until the required setting
is displayed.
5. Make the selection with setting buttons + - X.
6. Press and hold the Info button ( 8 for 3 seconds.
The chosen setting has now been stored.
You have the option of resetting all changed settings
back to the original factory settings.
Note: When you reset your dishwasher to the factory
settings, you are taken directly to the settings for
switching on the appliance for the first time.
Settings
Switching on the
appliance for the first
time
Factory setting Infotext
by pressing Info button (
Language American English Language selection.
Time format 24h 12h or 24h.
Time setting 12:00 Set the current time.
Water soft setting °E 0 - 8 soft Setting water hardness. When using Multitabs, select the
lowest setting.
Rinse aid setting Level 5 Amount of rinse aid affects drying.
Setting Factory setting Infotext
by pressing Info button
Time setting 12:00 Set the current time.
Time format 24h 12h or 24h.
Time display Time Show end of wash cycle with display "Time" or "In hours".
Language American English Language selection.
Water hardness °E0-8 Soft Setting water hardness. When using Multitabs, select the
lowest setting.
Rinse aid disp. Level 5 Amount of rinse aid affects drying.
Sensor setting Standard Adjusting water clarity detection for best cleaning results.
Extra dry Off Improved drying for glasses and plasticware.
Eco forecast Off Show the water and energy consumption.