Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
18
en-us Rinse Aid
Using detergents with salt component
Det er ge nt with a sal t component
If combined detergents with a salt component
are used, special salt can usually be omitted up
to a water hardness of 21° dH (37° fH, 26° Clarke,
3.7 mmol/l). If the water hardness is over 21° dH, salt
must be used.
Switching off low salt indicator / water
softening system
Switching of f wat er sof t eni ng syst em
If the use of combined detergents with a salt
component impairs the low salt indicator P on the
control panel or the text on the display window at the
top @ (enough salt for x rinse cycles), the displays
can be switched off.
Proceed as described under “Setting water softening
system” and set the value to 0-8. The water softening
system and salt refill indicator are now switched off.
,
Rinse Aid
Rinse Aid
As soon as the low rinse aid indicator H lights up on
the control panel, rinse aid should be topped off.
The rinse aid is required for stain-free utensils and clear
glasses. Use only rinse aid which the manufacturer
designates as safe to use in domestic dishwashers.
Combined detergents with rinse aid component may be
used with soft to moderately hard water only (0-2 bands
on test strip or up to an °E value of 20). For moderately
hard to hard water (3 to 4 bands on test strip or °E value
of 21 or higher), rinse aid must be used.
Adding rinse aid
NOTICE: To avoid oversudsing or clogging, do not
overfill the rinse aid dispenser 9". Wipe up any spills
with a damp cloth.
1. Open the rinse aid dispenser 9" by pressing on the
latch of the lid and pulling it open.
2. Add liquid rinse aid to the dispenser 9" until it is
full. Do not overfill. Avoid spilling into air vent hole.
PD[
WFOU
BJS